NORDKISA Open Wardrobe Assembly Instructions
General Assembly Tips
Before starting assembly, please review these important tips:
- Ensure the assembly area is clean and spacious.
- Use a spirit level [level tool] to ensure the unit is stable and level.
- It is recommended to have two people [two people lifting] for lifting and assembling larger parts to prevent injury or damage.
- Assemble on a soft surface, such as a rug [assemble on rug], to protect the furniture and your floor from scratches. Avoid assembling directly on hard surfaces that could cause damage [assemble on hard surface X].
- If you encounter any difficulties or have questions during assembly, please refer to the IKEA website or contact IKEA customer service [contact IKEA].
Parts List
Identify all parts and hardware before beginning assembly. Quantities are indicated.
- 53x Screws [screw] (Part No: 10040625)
- 1x Dowel [dowel] (Part No: 195474)
- 1x Screw [screw] (Part No: 151905)
- 4x Bolts [bolt] (Part No: 157732)
- 44x Dowels [dowel] (Part No: 101345)
- 1x Allen Key [allen key] (Part No: 100006)
Assembly Steps
-
Step 1
Insert 8 dowels [dowel] (101345) into the designated holes on two large panels.
-
Step 2
Assemble the main frame. Connect two side panels to the base panel using 4 screws [screw] and the Allen key [allen key] (100006). Ensure connections are secure.
-
Step 3
Attach the first slatted back panel to the assembled frame. The diagram shows a rotating action [rotate] to position the panel.
-
Step 4
Secure the slatted back panel to the frame using 2 dowels [dowel] (101345).
-
Step 5
Attach the top panel to the frame. The diagram shows an insertion action [arrow].
-
Step 6
Attach the side panels to the main structure using 7 screws [screw] and the Allen key.
-
Step 7
Insert 12 dowels [dowel] (101345) into the designated holes on the shelf panels.
-
Step 8
Attach the back panels to the structure using 4 screws [screw] (10040625).
-
Step 9
Insert the internal divider panels into the structure. The diagram shows a sliding insertion action [arrow].
-
Step 10
Attach the side panels to the internal structure using 6 dowels [dowel] (101345).
-
Step 11
Attach the other side panel to the structure. The diagram shows a manual insertion action [hand].
-
Step 12
Secure the main cabinet structure by inserting 9 screws [screw] (10040625).
-
Step 13
Assemble the hanging rail. Insert a dowel [dowel] (10040625) into the rail support, then attach the rail.
-
Step 14
Attach the hanging rail support to the cabinet structure using 1 screw [screw] (10040625).
-
Step 15
Attach the hanging rail to the support using 1 screw [screw] (10040625).
-
Step 16
Assemble the base frame. Connect the long base rails to the leg supports using screws [screw].
-
Step 17
Attach the legs to the base frame using 4 bolts [bolt] (157732).
-
Step 18
Flip the assembled base frame over [rotate].
-
Step 19
Place the main cabinet structure onto the assembled base frame. The diagram shows an alignment action [arrow].
-
Step 20
Secure the main cabinet structure to the base frame using 10 screws [screw] (10040625).
-
Step 21
Rotate the entire unit upright [rotate].
-
Step 22
Attach the hanging rail support to the side panel using 6 dowels [dowel] (101345).
-
Step 23
Attach the top panel to the cabinet structure. The diagram shows an insertion action [arrow].
-
Step 24
Attach the sliding door. The diagram shows a connection point [connection point] and requires 2 screws.
-
Step 25
Attach the top panel to the cabinet structure. The diagram shows an insertion action [arrow].
-
Step 26
Secure the top panel to the cabinet structure using 9 screws [screw] (10040625).
-
Step 27
Attach the hanging rail support to the side panel using 1 dowel [dowel] (195474) and 1 screw [screw] (151905).
Final Adjustments
Adjust the feet [adjust feet] of the unit as needed to ensure stability and level placement. This typically involves turning the feet [rotate].
