User Manual for NEO models including: Neo Smart Tube KIT, T8-7X RGBWW LED Pixel Tube, T8-7X, RGBWW LED Pixel Tube, LED Pixel Tube, Pixel Tube
Macaio | Neo Smart Tube KIT - Macaio
File Info : application/pdf, 19 Pages, 2.83MB
DocumentDocumentSMART TUBE MAGIC PIXEL TUBE USER MANUAL | MANUAL DE USUARIO PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE POR FAVOR LEA LAS INSTRUCCIONES ANTES DE USAR P. 1 Versión Español | Tecshow NEBULA PAR 162 II UNDERSTANDING OF PRODUCT Security Warning When unpacking and before disposing of the carton, check if there is any transportation damage before using the product. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus. · Product should install in a cool place. Keep away from the wall 50cm. · Do not install the product or project the beam onto inflammable surfaces. Minimum distance is 5 M · The product is only intended for installation, operation and maintenance by qualified personnel. And read the user manual and labels on the lighting carefully before use. · Do not look directly at the lamp light (especially for epilepsy), so as not to cause damage to the eyes. · Keep the optical system clean. Do not touch the LED lens with bare hands. Do not use any alcohol liquid or any other liquid to clean the optical system. Use medicinal absorbent cotton to clean it. · Please do not attempt to dismantle and/or modify the product inner structure. Otherwise, would not provide 1 year of free warranty. · Electrical connection must only be carried out by qualified personnel. · Before installation, ensure that the voltage and frequency of power supply match the power requirement of the product. It is essential that each product is correctly earthed and that electrical installation conforms to all relevant standards. · Do not connect this device to any other types of dimmer apparatus. · Make sure that the power-cord is never crimped or damaged by sharp edges.Never let the power-cord come into contact with other cables. Only handle the power-cord by the plug.Never pull out the plug by tugging the power-cord. · There is no user serviceable parts inside the product, do not open the housing and never operate the product with the cover removed. · There are protection structure and circuit for the battery inside the unit, any inappropriate dismount of the light or battery might break the protection function and lead to batter getting hot, smoking, deforming or fire. · Never short-circuit the unit. · Heating and burning will melt the battery separator, causing loss of protection function or burning of electrolyte and overheat will cause heating, smoking, deformation or burning of batteries. · Never use the unit in an environment over 40 , not to charge the unit close to fire source or under direct sun. Even never wet or throw the unit to water, otherwise, the protection function inside the batter might lose or abnormal chemical reaction might arise, causing battery to be hot, smoking, deformation or fire. · It is dangerous charging not to use the supplied power adapter. · Never break the light or battery, not to weld the battery or dismount the battery to be used in other equipment, not to touch the leaked battery electrolyte. · Place the unit where kids can't reach. P. 2 English Version | NEO- Smart Tube · If the charging time over the standard charging time for long, it is advised to stop charging. It will · 2 extend the charging time if charging while using, it is advised to turn off the light when charging. · Never place the unit inside microwave oven or any pressure container, instant heating or leakage (or abnormal smell), the unit should be abandoned and treated properly. · Not to use the unit in an environment where there is static electricity, the battery protection circuit might easily get broken if the static electricity is over 1000V, causing battery working abnormally, heating, smoking, deforming or fire. · When using, keep away of hot source, high pressure, avoid kids, never throw or hit the unit. · Use the supplied power adapter only, never charging over 24 hours. · When not using the unit for long term, please save the unit properly in a dry place, battery should be half charged. · Please bury the used unit, never throw to fire or water. If you have any questions,don't hesitate to consult our dealer or manufacturer. IMPORTANT: BEFORE ANY INSTALLATION, MAINTENANCE AND CLEANING, PLEASE ENSURE THAT THE POWER CUT OFF! MAIN TECHNICAL PARAMETERS · Lithium battery · Charging Voltage: DC12.6V/2A · Battery Specification: 21700 4.2V/4.5Ah*12 cells (12.6V/19.6Ah) · Charge Time: 8~10 hours · Circulation Life: Not less than 300 times · Run Time Of Battery : Max. 20h · LED · LED Type: 288pcs ×0.3Watts RGBW 4in1 full-color LED · Control Pixel: 32 Pixels · Rated Power: 50W · Colors: 16.7 million colors (0~100% saturation dimming) · Life: 50000 hours · Control · Control Protocol: International standard DMX-512 signal · Channel Protocol: 7 kinds of control channel mode. 2CH; 4CH; 6CH; 11CH; 32CH -8 Pixels; 64CH · -16 Pixels; 128CH -32 Pixels; · Control Mode: DMX-512,auto,master-slave,music,infrared remote control,wireless DMX-512 and · Mobile APP WIFI control. · Wireless Protocol: W-DMX · Wireless DMX Specs · 2.4G Communication Distance: 200M (clearing, it changes vary with different environments) · WIFI Communication Distance: 30M (clearing, it changes vary with different environments) · Band: 2.4G ISM, 126 channel frequencies · Maximum Transmit Power: 20dBm · Receiver Sensitivity: -94dBm P. 3 English Version | NEO- Smart Tube MAIN TECHNICAL PARAMETERS · Optical System · Dimmer: From 0~100 linear dimming. · Flashing Rate: 1~20Hz · Beam Angle: 180° · Physical · Dimensions: Ø52 x 1190 mm · Weight: 1.72kg · Security · Cooling System: Convection · Waterproof Rate: IP65 · Temperature Protection: 60 · Operating Environment: Indoor / Outdoor PRODUCT FEATURES Using the latest LED control technology. The newest intelligent LED pixel tube light can realize intelligent operation and control through its special menu at the back. This product is designed for stage and around event sites and can be used to create stunning lighting effects, it is affordable also very powerful battery LED tube, A highly creative device that offers an infinite range of possibilities. Its main features include: 1) Product built-in lithium battery and the DMX signal wireless module. 2) Product built-in WIFI receiving module, which can be controlled by mobile APP. 3) Wireless DMX with transceiver function. 4) With music control function. 5) Custom color temperature settings. 6) Built-in commonly used film and television shooting effects. 7) With charging protection and current overload protection. 8) Intuitive and convenient battery display function. 9) The static power consumption of the control panel is 0.3W, and its efficiency will reach up to 97% during the process of high power output, which realizes the function of eco-friendly operation. 10) Overheating automatic protection function. 11) IR infrared remote control panel. 12) Touch button and LCD display. 13) Password protected keyboard. 14) 7 kinds DMX working mode. 15) Built-in 68 kinds of Auto effect. 16) Master-slave control, multi-units for synchronous wireless control. 17) Software system updates&upgrades are available through DMX 512 or wireless DMX. P. 4 English Version | NEO- Smart Tube PRODUCT PACKING INFORMATION Following accessories are packed together with the product, please check them carefully upon unpacking. Spare parts Magic Tube light Charger DMX signal cable IN&OUT Infrared remote controller Instruction Manual Name 1 1 2 1 1 QTY piece piece pieces piece piece PRODUCT INSTALLATION DMX Connection Method When set the DMX512 address code be CH4 MODE, as below: Unit Remark · Wireless DMX transmitter should be connected to the DMX-512 controller. · Since CH4 MODE has 4 channels, the address code with 4 increment increasing progressively (e.g., 1,5,9,13...) · Every DMX address code can be reused as needed. · DMX address code can be any data between 001 and 512. P. 5 English Version | NEO- Smart Tube 4G-WIRELESS MASTER-SLAVE CONNECTION METHOD · As Below · Set the wireless DMX signal of the first light to the sending state (Master), and the wireless DMX signal of other lights to the receiving state (Slave). · When the Slave is set to DMX512 control mode, running auto effect or other static colors on the Master to achieve the wireless master-slave synchronization. · The DMX address code of the Master and Slave can be any data between 001 and 512 without affecting master-slave online. MOBILE APP WIFI MASTER-SLAVE CONNECTION METHOD · Establish wireless communication between WIFI control of mobile phone and WIFI control of lights according to 3.5.7. · Set the wireless DMX signal of the first light to the sending state (Master), and the wireless DMX signal of other lights to the receiving state (Slave). · When the Slave is set to DMX512 control mode, running auto effect or other static colors on the phone APP to achieve the wireless master-slave synchronization. · The DMX address code of the Master and Slave can be any data between 001 and 512 without affecting master-slave online. P. 6 English Version | NEO- Smart Tube OPERATION METHOD Back panel functions introduction Menu button/return button,enter the menu selection interface or previous menu. Confirmation button,used to confirm the selected function. / Upward/downward select function or Parameter increment / decrement. POWER IN DC12.6V/2A: Charging port, both available. DMX IN / OUT: DMX-512 signal Input / Output. 4G WIRELESS DMX CONNECTION METHOD Working mode 2.4G wireless DMX transceiver uses the W-DMX communication protocol which has two working modes: Transmit mode and Receive mode. · Find (Set) menu and press (ENTER) to enter system settings menu. · Press (UP/DOWN) key to select (Wireless 2.4g) to enter 2.4g wireless DMX settings menu. · (WIRELESS) for wireless DMX control ON/OFF. (CONNECT) means the paired connection of wireless DMX module. (RESET) means reset the data of wireless DMX control setting,(MODE) has transmitting mode and receiving mode. P. 7 English Version | NEO- Smart Tube 4G-WIRELESS MASTER-SLAVE CONNECTION METHOD · As Below WORKING W-DMX Receive W-DMX Transmit MODE White Red fast flash Green fast flash Green slow flash Green Red Blue fast flash Blue slow flash Blue ACTION STATUS DESCRIPTION Connection is not established Connection is lost Connecting to transmitter Connected. Without DMX signal Connected. Receiving DMX signal Deleting all receivers' connection Connecting with the Receiver(s) No DMX signal input Transmitting DMX signal · Note: The wireless transceiver will remember the chosen protocol even after you disconnecting the power supply. There is no need for repeated setting. Working mode · According to step 3.2.1 set the Slave to (Receive)mode. · (Select) (Reset) menu to reset wireless connection. At this time, the indicator light is white, indicating that the wireless module is not connected to transmit module and is ready to receive the paired signal. · According to step 3.2.1 set the Master to (Transmit) mode. At this time, the indicator light is blue slow flash, indicating that the wireless module is not connected to DMX signal. · (Select) (Reset) menu to reset wireless connection. At this time, the indicator light is red, indicating that the connected receiving module is being deleted. · (Select) CONNECT to transmit wireless paired signal, at this time the indicator light is blue fast flash. · When the Slave receive the paired signal from Master, the indicator light is Green fast flash which means the connection is established. P. 8 English Version | NEO- Smart Tube INFRARED REMOTE CONTROLLER INSTRUCTION MENU DISPLAY · Dimming up · Dimming down · Off light off · ON light on · R / G / B / W for 4 single color, A / UV (None) · 9 number keys meas 9 kinds of static mix colour (AC1...... AC9) · The "0" key for is to enter DMX-512 control state · AUTO key is color change mode, press up and down key to adjust speed · STROBE key is in color strobe mode (32 types are optional), press up and down key to adjust · speed. · FADE key is for color fading mode, press up and down key to adjust speed. · SOUND key is for sound control mode, press up and down key to adjust the sound control sensitivity. · Note: The IR remote controller should be pointed at the IR infrared receiver. Otherwise, the light will not be controlled. P. 9 English Version | NEO- Smart Tube MENU OVERVIEW Main menu Primary-menu Sub-menu Function Note DMX Mode 001--512 Show Auto Sound Static Color WIFI WIFI DMX address setting and Receive mode DMX console mode Auto Mode 0-68 Speed:1-16 1-16 on speed setting Sound Mode 1-4 68 kinds of Auto effect 1-16 from slow to fast on speed setting Color setting, 0 for automatic color change, a total of 15 colors 4 sound control modes optional Sens 1-100 Sound sensitivity setting Color 0-15 Color setting, 0 for automatic color change, a total of 15 colors Dimmer 000-255 Overall dimming Strobe 000-255 Strobe Red 000-255 Red dimming Green 000-255 Green dimming Blue 000-255 Blue dimming White 000-255 White dimming Red Cyan Blue+W Green Purple Yellow+W Blue Warm White Cyan+W White Red+W Purple+W Yellow Green+W Full 2800K, 3000K, 3200K, 3500K, 3800K, 4000K, 4500K, 5000K, 5600K, 6000K, 6500K, 7000K, 7500K, 8000K, 8500K, 9000K, 9500K, 10000K Auto mode Static color mode Built in static color mode Color temperature mode On the phone, connect WIFI address "Led_XXX" and turn on the APP WIFI mode ( LED LAMP)to control P. 10 English Version | NEO- Smart Tube INFRARED REMOTE CONTROLLER INSTRUCTION Set DMX Channel 2CH/4CH/6CH/11CH/32CH/64CH/128CH 7 DMX channel modes DMX Fail Status of light fixture after DMX fail Display Reverse Display Reverse OFF / ON Display On Time Display start time Menu Lock When Menu Lock is ON, the button will is locked after 30 seconds without any operation, and press the UP+DOWN button for 5 seconds to unlock. IR Remote Infrared remote control OFF / ON Wireless 2.4g Wireless OFF / ON Wireless DMX OFF / ON Connect NO / YES Reset NO / YES Mode Receive / Transmit Factory Set 1.Red 0-255 Limit the red brightness value, 10 factory default value is 220 2.Green 0-255 Limit the green brightness value, factory default value is 220 3.Blue 0-255 Limit the blue brightness value, factory default value is 220 4.White 0-255 Limit the white brightness value, factory default value is 220 5.State Single / Whole Single: only the current color, Whole: full color working 6.T.Limit 40-100 Set the start temperature of temperature protection Factory Reset NO / YES YES: Restore factory settings Info Name MAGIC Version V1.0 P. 11 English Version | NEO- Smart Tube DMX ADDRESS SETTINGS (DMX512) · Find (DMX Mode) menu and press (ENTER) to enter DMX address code setting. · Press (UP/DOWN) button to adjust parameters. · After setting the DMX address code, press (ENTER) to save the settings. AUTO EFFECT SETTINGS (AUTO): · Find (Auto)menu and press (ENTER) to enter auto effect setting. · Press: (UP/DOWN) button to select (Auto Mode), (Speed) or (Color). · Press (ENTER) to enter the settings. · Press (UP/DOWN) button to select auto effect, speed, or color, press (ENTER) to save the settings. SOUND EFFECT SETTINGS (SOUND): · Find (Sound) menu anda press (ENTER) to enter sound effect setting. · Press (UP/DOWN) button to select(Sound Mode),(Sens) or (Color). · Press (ENTER)to enter the settings. · Press (UP/DOWN)button to select sound effect, sound control sensitivity or color effect, press · ENTER to save the settings STATIC COLOR SETTINGS (STATIC): · Find (Static) menu and press(ENTER)to enter static color setting. · Press (UP/DOWN) button to select(Dimmer),(Strobe),(Red),(Green),(Blue) or(White). · Press(ENTER) to confirm menu and press (UP/DOWN) button to adjust parameters, then press · (ENTER)to save the settings. P. 12 English Version | NEO- Smart Tube BUILT-IN STATIC COLOR SETTINGS (COLOR): · Find (Color) menu and press (ENTER)to enter built-in static color setting. · Press (UP/DOWN) button to select(Red),(Green),(Blue)... 15 built-in colors. · Press(ENTER)to save the settings. COLOR TEMPERATURE SETTINGS (CCT) · Find (CCT) menu and press (ENTER) to enter color temperature setting. · Press (UP/DOWN)button to select (2800K)(3000K)(3200K)... 18 kinds of color temperature · effect. · Press (ENTER) to save the settings. Hold (ENTER) for more than 3 seconds to enter the screen · for customizing the current color temperature. · Built-in (Red),(Green),(Blue),(White) 4 base colors with 0~255 brightness adjustment, can · freely customize the current color temperature according to your needs. MOBILE APP CONTROL MODE SETTINGS (WIFI) · Find (WIFI) menu and press (ENTER) to turn on WIFI. · "Led_XXX" displayed on the screen is the WIFI address of the light fixture. · Scan the above QR code to install (LED LAMP) APP first on mobile phone. · On the phone, find WIFI and search WIFI address, and the words beginning with LED appear. For · example, "LED-XXX", click the link. · Turn on the LED LAMP APP installed on the phone and show the link is successful then you can control it. P. 13 English Version | NEO- Smart Tube SYSTEM SETTINGS (SET) · Find Set menu and press ENTER to enter system setting. · Press UP/DOWN button to select corresponding function setting. · After setting, press ENTERto save the settings. FACTORY SETTINGS (FACTORY SET) · Find Factory menu and press ENTER to enter factory setting. · Press UP/DOWN button to select corresponding function setting. · After setting, press ENTER to save the settings. · Note: This the factory default setting, do not change it if unnecessary. MENU LOCK FUNCTION (MENU LOCK) · Form Set menu to find Menu Lock menu. · Press ENTER button to enter select ON. · When the menu locked, at the same time long press button , the display appears a small lock · icon and have a number count down to "0", it will unlock successfully. CHARGING DISPLAY · Note: In the process of charging, the display screen will have a charging display. If the lamp needs to work · while charging, long press MENU button to enter for operate menu. P. 14 English Version | NEO- Smart Tube DMX CHANNEL TABLE 2CH 2CH MODE: Channel 10 2 DMXD ata Controlf unction 255 Overalld immerL 01 0N OF UNCTION 11 24 2800K 25 38 3000K 39 52 3200K 53 66 3500K 67 80 3800K 81 94 4000K 95 108 4500K 109 122 5000K 123 136 5600K 137 150 6000K 151 164 6500K 165 178 7000K 179 192 7500K 193 206 8000K 207 220 8500K 221 234 9000K 235 248 9500K 249 255 10000K 4.1.2----4CH 4CH Mode: Channel DMXD ata Controlf unction 10 255 Redd immerL 20 255 Green dimmer 30 255 Blue dimmer 40 255 Whited immerL 4.1.3----6CH 6CH Mode: Channel DMXD ata Controlf unction 10 255 Overalld immerL 01 0 2 Strobe 11 255 30 255 Redd immerL 40 255 Green dimmer 50 255 Blue dimmer Detail description ineard imming from 0~100% CCT Detail description ineard imming from 0~100% Linear dimmingf rom0 ~100% Linear dimmingf rom0 ~100% ineard imming from 0~100% Detail description ineard imming from 0~100% NO FUNCTION Froms lowt of ast(1HZ-20HZ) ineard imming from 0~100% Linear dimmingf rom0 ~100% Linear dimmingf rom0 ~100% P. 15 English Version | NEO- Smart Tube DMX CHANNEL TABLE 6 0 255 White dimmer 4.1.4----11CH 11CH Mode: Channel DMX Data Control function 1 0 255 Overall dimmer 0 10 2 Strobe 11 255 0 10 3 Static macro 11 255 0 10 4 Macro background color 11 255 5 0 255 Macro background color brightness 0 10 11 220 221 6 229 228 Macro 236 237 244 245 255 7 0 255 Macro speed 8 0 255 Red dimmer 9 0 255 Green dimmer 10 0 255 Blue dimmer 11 0 255 White dimmer 4.1.5----32CH 32CH Mode: Channel DMX Data Control function 1 0 255 Red 1 dimmer 2 0 255 Green 1 dimmer 3 0 255 Blue 1 dimmer 4 0 255 White 1 dimmer 29 0 255 Red 8 dimmer 30 0 255 Green 8 dimmer 31 0 255 Blue 8 dimmer 32 0 255 White 8 dimmer Linear dimming from 0~100% Detail description Linear dimming from 0~100% NO FUNCTION From slow to fast(1HZ-20HZ) NO FUNCTION 17 values for each color NO FUNCTION 17 values for each color Linear dimming from 0~100% NO FUNCTION 3 values for each macro effect Sound control mode 1 Sound control mode 2 No function Sound control mode 3 From slow to fast Linear dimming from 0~100% Linear dimming from 0~100% Linear dimming from 0~100% Linear dimming from 0~100% Detail description Linear dimming from 0~100% Linear dimming from 0~100% Linear dimming from 0~100% Linear dimming from 0~100% Linear dimming from 0~100% Linear dimming from 0~100% Linear dimming from 0~100% Linear dimming from 0~100% P. 16 English Version | NEO- Smart Tube DMX CHANNEL TABLE 4.1.6----64CH 64CH Mode: Channel DMXD ata Controlf unction 10 255 Red1 dimmer 20 255 Green 1d immerL 30 255 Blue1 dimmer 40 255 White1 dimmer 61 0 255 Red1 6d immerL 62 0 255 Green16 dimmer 63 0 255 Blue 16 dimmer 64 0 255 White1 6d immerL 4.1.7----128CH 128CH Mode: Channel DMXD ata Controlf unction 10 255 Red1 dimmer 20 255 Green 1d immerL 30 255 Blue1d immerL 40 255 White1 dimmer 125 0 126 0 127 0 128 0 255 Red3 2d immerL 255 Green 32 dimmer 255 Blue 32 dimmer 255 White3 2d immerL MAINTENANCE Detail description Linear dimmingf rom0 ~100% ineard imming from 0~100% Linear dimmingf rom0 ~100% Linear dimmingf rom0 ~100% ineard imming from 0~100% Linear dimmingf rom0 ~100% Linear dimmingf rom0 ~100% ineard imming from 0~100% Detail description Linear dimmingf rom0 ~100% ineard imming from 0~100% ineard imming from 0~100% Linear dimmingf rom0 ~100% ineard imming from 0~100% Linear dimmingf rom0 ~100% Linear dimmingf rom0 ~100% ineard imming from 0~100% PRODUCT MAINTENANCE · To prolong the life of the product,it is very important to do maintenance work. The environment is hash · outdoors, or if the product is idle for a long time, damp, smoke or particularly dirty surroundings can · cause greater accumulation of dirt on its LED lens cover, fan vents and housing. So it should be cleaned · to maintain an optimum light output and at the same time to prevent it from corrupted by acid gas. · Cleaning frequency depends on the environment in which the fixture operates.Soft cloth and typical glass · cleaning products should be used for cleaning.It is recommended to clean product at least one every 20 · days. · Friendly notice: Please do not use any organic solvent, e.g.alcohol to · clean housing of the apparatus, lest cause damage. P. 17 English Version | NEO- Smart Tube DMX CHANNEL TABLE PRODUCT MAINTENANCE Action The battery is dead.C harging it. Thep roduct doesn't Powers upplyi s damagedo r abnormal.C alla qualified personnelt of ix it. switch on Controls ection is damaged. Call a qualified personnel to fixi t. Connection of internal circuitryi s not correct.C alla qualified personnelt of ix it. Thep roduct cant urn DMX addressi sw ronglys etting up. Resettingi ta ccording to instruction book. on,but LEDsd o not emit DMX Signalw ronglyc onnected. Connect it correctly accordingt oi nstruction book. light and are out of control Controls ection is damaged. Call a qualified personnel to fixi t. The beam appearsd im Thep roduct is too hot.Takev entilation measures to make it cool. · Remark: This product warranty for one year. We provide pay-needed maintenance service after the · warranty. But because of natural and man-made disasters or improper operation caused damage not · under warranty range. P. 18 English Version | NEO- Smart Tube P. 19 Versión Español | Tecshow NEBULA PAR 162 II