ITEMS INCLUDED IN THE BOX
- A: Emergency Battery Backup Unit (x1) - A rectangular unit with a flexible conduit and connectors.
- B: M12 test switch with cover (x1) - A wall-mounted switch with indicators.
- C: Wall plate screw (x2) - Screws for mounting.
- D: Wire nut (x13) - Connectors for electrical wires.
CONNECTION DETAILS
⚠️ WARNING: BEFORE STARTING INSTALLATION, SHUT THE LINE FEED POWER OFF USING THE CIRCUIT BREAKER.
Instructions pertaining to a risk of fire, electric shock or injury to persons. Installation must be done according to local electrical codes. Installation must be done by a qualified electrician.
- The Emergency LED driver must connect to 0-10V dimming wires (DIM+,DIM-) of the fixture if the LED luminaire power exceeds the emergency LED driver power.
- When dimming to minimum, the LED luminaire power must be less than emergency driver's power.
- In emergency mode, double-click this test switch to turn off the current emergency stage.
WIRING DIAGRAMS FOR LED DRIVER WITH INPUT POWER HIGHER THAN EMERGENCY OUTPUT POWER
REC-EMD08: 60W MAX. | REC-EMD15: 100W MAX.
1. 0-10V LED DRIVER + DIMMER SWITCH
Connect emergency driver DIM+ (Green wire) and DIM- (Yellow wire) to the LED Driver's DIM+ and DIM- wires respectively.
Diagram Description:
- Emergency Driver (A): Wires include Green (DIM+), Yellow (DIM-), Red (12V+), Black (12V-), White (Sensor+).
- Test Switch (B): Connected to the Emergency Driver.
- AC Power Input (from Wall Switch/Source):
- Yellow/Green wire to GND (Ground)
- Black wire to AC-L (SW)
- Blue wire to AC-L OUT (SW)
- White wire to AC-N (SW)
- 0-10V LED Driver:
- Connects to AC power (Black wire to AC-L (LED), White wire to AC-N (LED)).
- Connects to LED fixture (Green wire to DIM+ (LED), Yellow wire to DIM- (LED)).
- Connects to 0-10V Dimmer (Purple wire to DIM+ (0/10V), Pink or Grey wire to DIM- (0/10V)).
- Emergency Driver to 0-10V LED Driver:
- Green wire (DIM+) from Emergency Driver connects to DIM+ (0/10V) on 0-10V LED Driver (Purple wire).
- Yellow wire (DIM-) from Emergency Driver connects to DIM- (0/10V) on 0-10V LED Driver (Pink or Grey wire).
- Optional DC 12V Sensor: Connects to 12V+ (Red wire), 12V- (Black wire), and Sensor+ (White wire) from the Emergency Driver.
Wall switch and 0-10V Dimmer are not included.
WIRING DIAGRAM FOR LED DRIVER WITH INPUT POWER LESS THAN EMERGENCY OUTPUT POWER
REC-EMD08: 8W MAX. | REC-EMD15: 15W MAX.
2. 0-10V LED DRIVER + WALL SWITCH
Connect emergency driver DIM+ (Green wire) and DIM- (Yellow wire) to the LED Driver's DIM+ and DIM- wires respectively.
Diagram Description:
- Emergency Driver (A): Wires include Green (DIM+), Yellow (DIM-), Red (12V+), Black (12V-), White (Sensor+).
- Test Switch (B): Connected to the Emergency Driver.
- AC Power Input (from Wall Switch):
- Yellow/Green wire to GND (Ground)
- Black wire to AC-L (SW)
- Blue wire to AC-L OUT (SW)
- White wire to AC-N (SW)
- 0-10V LED Driver:
- Connects to AC power (Black wire to AC-L (LED), White wire to AC-N (LED)).
- Connects to LED fixture (Green wire to DIM+ (LED), Yellow wire to DIM- (LED)).
- Emergency Driver to 0-10V LED Driver:
- Green wire (DIM+) from Emergency Driver connects to DIM+ (0/10V) on 0-10V LED Driver (Purple wire).
- Yellow wire (DIM-) from Emergency Driver connects to DIM- (0/10V) on 0-10V LED Driver (Pink or Grey wire).
- Optional DC 12V Sensor: Connects to 12V+ (Red wire), 12V- (Black wire), and Sensor+ (White wire) from the Emergency Driver.
Wall switch is not included.
3. TRIAC / ELV DIMMABLE LED DRIVER
Connect emergency driver DIM+ (Green wire) and DIM- (Yellow wire) to the LED Driver's DIM+ and DIM- wires respectively.
Diagram Description:
- Emergency Driver (A): Wires include Green (DIM+), Yellow (DIM-), Red (12V+), Black (12V-), White (Sensor+).
- Test Switch (B): Connected to the Emergency Driver.
- AC Power Input (from Wall Switch or TRIAC/ELV Dimmer):
- Yellow/Green wire to GND (Ground)
- Black wire to AC-L (SW)
- Blue wire to AC-L OUT (SW)
- White wire to AC-N (SW)
- LED Driver:
- Connects to AC power (Black wire to AC-L (LED), White wire to AC-N (LED)).
- Connects to LED fixture (Green wire to DIM+ (LED), Yellow wire to DIM- (LED)).
- Emergency Driver to LED Driver:
- Green wire (DIM+) from Emergency Driver connects to DIM+ (0/10V) on LED Driver (Purple wire).
- Yellow wire (DIM-) from Emergency Driver connects to DIM- (0/10V) on LED Driver (Pink wire).
- Optional DC 12V Sensor: Connects to 12V+ (Red wire), 12V- (Black wire), and Sensor+ (White wire) from the Emergency Driver.
Wall switch or TRIAC / ELV Dimmer is not included.
WARNINGS AND IMPORTANT INFORMATION
⚠️ CAUTION
Risk of shock: Disconnect emergency and normal input power sources before servicing any equipment connected to this unit.
⚠️ Risk of fire or electrical shock:
- This emergency battery pack installation requires knowledge of luminaire and electrical systems.
- Servicing of this equipment should be performed by qualified personnel only.
- Before installation, make certain the AC power to fixture is off.
- Suitable for use in 5°C -50°C ambient temperatures.
- Max. mounting height: 27.2 ft. for REC-EMD08 / 15.5ft for REC-EMD15
- Do not use outdoors.
- Do not mount near gas or electric heaters.
- Equipment should be mounted in locations and at heights where it will not be subjected to tampering by unauthorized personnel.
- The use of accessory equipment is not recommended by the manufacturer may cause an unsafe condition.
- The emergency battery pack is not for in an air-handling fixture.
- Do not use this equipment for other than its intended use.
IMPORTANT
- An unswitched AC power source is required (100-347 VAC, 50/60 Hz).
- Please charge the battery consistently for >24 hours for the first time usage so as to activate the whole battery cells of discharging/charging duration.
- Customers are advised to charge emergency LED drivers 24 hours every 6 months during storage, and which could be stocked for 1 year at most.
- If customers don't install and recharge for more than one year, the batteries may be damaged. This is not covered in the warranty, and we would charge for replacement.
REGULATORY NOTICES
FCC Notice
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
ISED Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
WARRANTY
DALS offers a 5 year warranty from the date of purchase which covers repairs or replacements of defective parts of the housing, optics, and electronics.
Dals Lighting | Manufacturer of designer lighting products
