SPF-1010-WB-TY Smart Pet Feeder

Quick Start Guide

Preface

Quick Start Steps:

• Scan the QR code on the packaging box or search 'Smartlife' from the App store to download the APP.
• Ensure the device's Wi-Fi indicator is rapidly blinking. If not, reset it by holding the OK button for 5 seconds until the power indicator flashes.
• Keep close to the feeder, then open your Bluetooth and App. The device will be automatically detected and shown in the App.
• Select 'Go to add' to automatically add the Pet Feeder in the "Small Home Appliances" list.

For more details about network pairing, refer to chapter 4.

Safety Notice

WARNING: Failure to follow these safety notices could result in fire, electric shock, other injuries, or damage to the Smart Pet Feeder and other property. Read all the safety notices below before using the Smart Pet Feeder.

• Avoid high humidity or extreme temperatures.
• Avoid long exposure to direct sunlight or strong ultraviolet light.
• Do not drop or expose the unit to intense vibration.
• Do not disassemble or try to repair the unit yourself.
• Do not expose the unit or its accessories to flammable liquids, gases, or other explosives.

Technical Specifications

1 Welcome

The Smart Pet Feeder allows you to feed your pet remotely or apply schedules for automatic feeding. You can get the feeding information anywhere at any time.

This guide will provide you with an overview of the product and help you get through the initial setup.

Features:

• Wi-Fi Remote control - Tuya APP smartphone programmable.
• Automatic & manual feeding.
• Accurate feeding - Schedule up to 20 feeds per day.
• 4L food capacity - 4L large capacity.
• Dual power protection - Battery backup, continuous operation during power or internet failure.

2 In the box

• Pet Feeder x 1
• Power Adapter x 1
• Quick Guide x 1

Please check the condition and the accessories of the pet feeder after you open the box.

APP Download:

1. Remove the cover and scan the QR Code with your smartphone.
2. Search 'Smartlife' APP from App store.

Tips:

Dry and solid pet food only. Recommended food diameter between 5 to 10mm.

[Diagram: Two representations of pet food kibble sizes, indicating a recommended diameter range of 5 to 10mm.]

3 Get to know your device

[Diagram: A Smart Pet Feeder with labels pointing to: Cover, Button & indicator (Open the cover), Food outlet, Bowl.]

Battery box:

Contains 3 x D-size batteries. Please pay attention to the polarity. Battery charging is for backup purpose only. If you wish to control the pet feeder remotely, power supply is needed.

Power switch:

[Diagram: Power switch labeled with 'ON' and 'OFF' symbols.]

Power jack:

Use the supplied power adapter.

OK Button and Wi-Fi Indicator

[Diagram: Top view of the Pet Feeder's lid showing the OK Button, Power indicator, and Wi-Fi indicator. Text labels in Chinese and English: "智能宠物喂食器 远程控制 定时定量 Smart Pet Feeder Remote feeding and interaction".]

OK Button:

• Tap once to feed once in 1 portion.
• Reset the network configuration.

Hold the 'OK' button for 5 seconds until the power indicator flashes once to reset. The device will enter the EZ pair mode at the first reset. If resetting the device again in the EZ pair mode, it will change to AP pair mode.

Wi-Fi indicator:

The Wi-Fi status gives the following information:

• EZ pair mode (Default): Quick pair devices. You can set all devices to this mode, and then add devices in batches on your phone.
• AP pair mode: If you would like to pair one specific device during many devices. Please refer to FAQ1 to configure network in this mode.

4 Get started

To get started, you will need:

• Connect your phone to the 2.4Ghz Wi-Fi network.
• A mobile phone with a mobile APP installed.

Then follow the steps below:

1. Power on the Smart Pet Feeder.
2. Make sure the Wi-Fi indicator is rapidly blinking. If not, please reset it.

4.1 Add devices

1. Open your App.
2. Login with an existing account. If you are a new user, you need to create an account first.
3. Turn on "Bluetooth" and "Location" on your phone before connecting the Wi-Fi.
4. [Diagram: Mobile phone screen showing Wi-Fi, Bluetooth, and Location settings enabled.]
5. Once logged in, the phone will automatically detect the device via Bluetooth. Choose "Go to add".
6. [Diagram: App screen showing "Devices to be added: 1" with a Pet Feeder icon, and buttons "Do not add" and "Go to add".]

5. Enter Wi-Fi Credentials:

Enter your home Wi-Fi account and password (Only support 2.4Ghz Wi-Fi), then tap the "Next" button.

[Diagram: App screen showing options for 2.4GHz and 5GHz Wi-Fi, with fields for Wi-Fi Name and Password, and a "Next" button.]

Other Device Adding Mode:

1. Configure the network in EZ mode:

Note: In this case, you do not need to turn on your phone's Bluetooth.

1. Click the '+' button at the top right corner of the App to add devices.
2. Select 'Pet Feeder' to add manually the Pet Feeder in the "Small Home Appliances" list.
3. [Diagram: App interface showing categories like Electrical, Lighting, Sensors, Large Home Appliances, Small Home Appliances, Kitchen Appliances, Pet, Exercise & Health, etc. The 'Pet' category is expanded to show 'Pet Feeder', 'Pet Treat Feeder', 'Pet Feeder With Camera', 'Pet Food Bucket', etc.]
4. Enter your home Wi-Fi account and password (Only support 2.4Ghz Wi-Fi), then tap the "Next" button.
5. Place the router, mobile phone, and Pet Feeder as close as possible. Confirm the indicator on your device is rapidly blinking, then tap "Next" to wait for connection.
6. [Diagram: A visual cue indicating to confirm the indicator is rapidly blinking, followed by a "Next" button.]

2. Configure the network in AP mode:

1. Reset the device in EZ pair mode; it will switch to AP pair mode. The indicator on your device will blink slowly.
2. Switch the network configuration mode to AP mode at the upper right corner of the APP when you add the device.
3. [Diagram: App screen showing a prompt "Reset the device fi..." with options "AP Mode" and "EZ Mode Default". "AP Mode" is selected.]
4. Place the router, mobile phone, and Pet Feeder as close as possible. Confirm the indicator on your device is slowly blinking, then tap "Next" to wait for connection.

2.4 After the device has been added:

You can use [pencil icon] to rename the device. (If failed, please refer to FAQ2 to troubleshoot)

6. Wi-Fi configuration of the device failed:

• Confirm the entered router password is correct.
• Ensure that the DHCP service is enabled for the router. If not, the IP address will be occupied.
• Please confirm the Wi-Fi network is stable: Put the phone beside your device and make sure they are in the same network environment. Try to open a website to judge if the network can be used.
• If your router supports both 2.4Ghz and 5Ghz, please enable the 2.4Ghz channel and add the device under the 2.4G Wi-Fi channel. You can follow the following step on the App to configure the router.
• [Diagram: App screen showing "Select 2.4 GHz Wi-Fi Network and enter password." with an instruction "If your Wi-Fi is 5GHz, please set it to be 2.4GHz." and options for 2.4GHz and 5GHz.]

Location and Bluetooth Permissions:

• Confirm that both the location permission of the phone system and the App are enabled.
• [Diagram: iOS Settings screen showing Privacy -> Location Services, and Smart Life app settings showing Location access (Always) and Bluetooth enabled.]
• If you have upgraded to iOS system 14, you need to enable the "Local network" and "Bluetooth" of the App.
• [Diagram: iOS Settings screen showing Smart Life app permissions with Location, Bluetooth, and Local Network enabled.]
• If it still does not work, it is recommended to change the router and try again.

7. Device offline:

• Confirm whether the Pet Feeder is powered on.
• Please confirm whether the home Wi-Fi network is normal, or whether the Wi-Fi name and password has been modified.
• If there are still problems after the above checking, it is recommended to remove the device or change the router to add it again.

8. Placement for Connection:

Place the router, mobile phone, and Pet Feeder as close as possible. Confirm the indicator on your device is rapidly blinking, then tap "Next" to wait for connection.

[Diagram: A visual cue indicating to confirm the indicator is rapidly blinking, followed by a "Next" button.]

9. Renaming the Device:

After the device has been added, you can use [pencil icon] to rename the device. (If failed, please repeat above steps.)

4.2 App Overview:

Home management

[Diagram: App screen showing "Home management" with tabs for Home, Smart, Me. It displays "Location Information" (Overcast, 79°F Outdoor Temperature, 83% Outdoor Humidity, 995 hPa Outdoor Air Pressure) and "Device List" showing "Wi-Fi: Smart Pet Feeder". Buttons for Add Device, Voice Control, Room Management are visible.]

Home Tab:

1. Device list: You can check the added device; tap one to enter the control board.
2. Location information: Information about your local weather conditions, outdoor temperature, PM.
3. Home management: Add or delete home and manage home names, rooms, locations, and members.
4. Room management: Manage rooms. You can create rooms and assign devices to each room.
5. Voice control: (Temporarily not available on App)

Smart Tab:

Create smart scenes and add automatic functions (Temporarily not available).

Me Tab:

App settings and FAQ about the app.

1. Control board:

Select the target Pet Feeder in the device list then enter the control board.

[Diagram: App screen for a specific Pet Feeder showing "Standby" status, a pet's avatar, "More settings" [gear icon], "Device settings" [gear icon], "Meal Plan" [clock icon], "Feed Record" [list icon], "Total portion" with +/- buttons, and a "Feed" button.]

Meal plan:

Tap to edit the schedule for automatic feed. Schedule supports up to 20 items. The error of the schedule is about 30 seconds.

Feed record:

Tap to check the feeding history.

Feed:

Tap to feed manually. The maximum number of portions is 20 at a time.

Feeder status display:

It will have three different statuses: Standby, Feeding, and Done.

Pet's picture setting:

Tap to set or change the pictures of your pet.

Total portion:

Tap "-" to reduce feeding portion and tap "+" to add feeding portion when manual feeding. The maximum number of portions is 20 at a time.

More settings:

Tap for more settings, like rename device, device information, third-party control, and others.

Device setting:

After confirmed to restore factory settings, the device will change to EZ pair mode and the cloud record will be cleared.

2. Food stuck alarm:

When the pet food gets stuck, the APP will receive the alarm, and the red light will flash slowly.

[Diagram: App screen showing a "Pet Food Jam" alert with an exclamation mark icon and a close button.]

3. Feeding plan display:

The next feeding time and the number of portions will be shown.

[Diagram: App screen showing "Standby" status, pet avatar, and "Next Time: 14.05.2021 12:09 Feeding1". Also shows "Meal Plan" option.]