GS1, GS2, GS3/DURAPULSE Accessories – Miscellaneous

GS3-KPD Keypad

Spare or replacement keypad for DURApulse AC drives; great for maintenance or back-up programs.

GS3-BZL Flush Mount Bezel Kit

The GS3-BZL Flush Mount Bezel Kit allows remote mounting of the DURApulse removable keypad. It features a Protected Chassis and IP20 enclosure rating. The thickness of the panel will determine required hole dimensions:

• Thickness 1.0 - 1.4 mm (0.0393 - 0.0551 in): Hole 81.0 mm (3.19 in)
• Thickness 1.6 - 2.0 mm (0.629 - 0.0787 in): Hole 82.0 mm (3.23 in)
• Thickness 2.2 - 3.0 mm (0.0866 - 0.1181 in): Hole 82.8 mm (3.26 in)

Overall dimensions: 115.0 mm (4.53 in) height. Mounting requires M4xP0.7 screws.

Keypad Cables

GS-CBL2-1L: One meter keypad cable (installation screws included).

GS-CBL2-3L: Three meter keypad cable (installation screws included).

GS-CBL2-5L: Five meter keypad cable (installation screws included).

ZIPLink Communication Distribution Modules

ZL-CDM-RJ12X4: 4-port ZIPLink communication distribution module with 4 RJ12 ports and 1 screw terminal port.

ZL-CDM-RJ12X10: 10-port ZIPLink communication distribution module with 10 RJ12 ports and 1 screw terminal port.

Optional ZIPLink serial communication cables are available for plug and play connectivity to AutomationDirect PLCs. Refer to the comm cable selection matrix on page tGSX-171.

Solution 1: DirectLOGIC, CLICK and Productivity I/O Modules to ZIPLink Connector Modules

For quick and easy I/O-to-field termination, use a ZIPLink connector module with a prewired ZIPLink cable (I/O terminal block at one end, multi-pin connector at the other).

Steps:

1. Locate your I/O module/PLC.
2. Select a ZIPLink Module.
3. Select a corresponding ZIPLink Cable.

Solution 2: DirectLOGIC, CLICK and Productivity I/O Modules to 3rd Party Devices

Connect I/O to nearby devices without extra terminal blocks using ZIPLink Pigtail Cables. These are prewired to an I/O terminal block with color-coded, soldered-tip wires on the other end.

Steps:

1. Locate your PLC I/O module.
2. Select a ZIPLink Pigtail Cable compatible with your 3rd party device.

Solution 3: GS Series and DURAPulse Drives Communication Cables

For Modbus RTU communication with drives or networks. ZIPLink cables connect PLCs, SureServo, SureStep, Stellar Soft Starters, and AC drives. A ZIPLink communications module can set up multi-device networks.

Steps:

1. Locate your Drive and type of communications.
2. Select a ZIPLink cable and associated hardware.

Solution 4: Serial Communications Cables

ZIPLink offers communication cables for DirectLOGIC, CLICK, and Productivity CPUs, and other communication devices. Connections include a 6-pin RJ12 or 9-pin, 15-pin and 25-pin D-sub connectors, usable with RJ12 or D-Sub Feedthrough modules.

Steps:

1. Locate your connector type.
2. Select a cable.

Solution 5: Specialty ZIPLink Modules

ZIPLink modules are available for various applications, including stand-alone relays, 24VDC and 120VAC transorb modules, D-sub and RJ12 feedthrough modules, communication port adapters, distribution modules, and SureServo 50-pin I/O interface connections.

Steps:

1. Locate the type of application.
2. Select a ZIPLink module.

Solution 6: ZIPLink Connector Modules to 3rd Party Devices

Pigtail cables with color-coded soldered-tip wires provide a clean, easy way to connect devices to terminal blocks, reducing troubleshooting time. Use with compatible ZIPLink Connector Modules.

Steps:

1. Select module type.
2. Select the number of pins.
3. Select cable.