PULSAR MANUAL

Features

• 1 (15 chips) COB high brightness red LED
• 2 AAA alkaline batteries
• 2 steady modes, 3 flashing modes
• Quick release universal bracket (fits all round and AERO style bars)
• Side visibility
• Water resistant (IPX 4)

Contents

• PULSAR
• 2 AAA alkaline batteries
• RB-22 (Universal bracket)
• 2 O-rings for mounting: RS-G for ⌀20-35mm, RS-H for ⌀35-52mm
• BK-21 (Belt clip)

Optional Accessories

• RB-19 (Rear rack bracket)
• RB-21 (Saddle rail bracket)
• RB-23 (Helmet bracket)
• RB-27 (GoPro mount adapter)

Operation

1. Press power button [press] → Turn on light.
2. Press power button [press] → Choose modes.
3. Double click power button [double click] → Toggle between steady and flashing modes.
4. Press power button for 1 sec [press] → Turn off light.

Diagram Description: Shows the power button and mode transitions. Double click toggles between Mode 1 and Mode 2. FL1, FL2, FL3 represent different flashing modes.

Runtime

Beam Angle: 300° Total Angle, 93° Spot Angle.

Batteries Changing

1. Open the bottom case with finger.
2. Install batteries aligning with [plus-minus poles].
3. Install the bottom case.
4. Do not mix new and old batteries.
5. Install batteries in correct direction.
6. Remove batteries from light for storage.

Diagram Description: Illustration shows the battery compartment being opened, batteries inserted correctly, and the case closed.

Mounting Instructions

Seatpost Mounting

1. Choose the strap to fit the seatpost.
2. Ensure the strap clicks [click] into place on the hook.
3. Hold the light on the seatpost.
4. Wrap the rubber strap around the seatpost and stretching strap around the hook to secure.
5. Slide the light forward onto the bracket until it clicks [click] into place.
6. Press down the release lever [release] to remove.
7. Adjust the horizontal/vertical beam angle when mounted on the handle bar/seatpost: loosen the screw knob, spin the light left to right → or up/down ↓↑ for your preferred angle, then tighten the screw knob to secure the light in place.

Diagram Description: Illustrates strap selection, securing the strap, sliding the light onto the bracket ([install], [click]), and releasing the light ([release]). Also shows adjusting the light angle.

Belt Clip Mounting

1. Slide light forward onto belt clip until it clicks [click] into place.
2. Press down the release lever [release] to remove.

Diagram Description: Shows attaching the light to the belt clip ([install], [click]) and releasing it ([release]).

Saddle Rail Mounting (Optional)

1. Loosen the screws in the saddle bracket with the Allen key.
2. Clamp the bracket onto the saddle rail.
3. Align the screw holes using the Allen key to tighten the bracket [clockwise].
4. Slide light forward onto bracket until it clicks [click] into place.
5. Press down the release lever [release] to remove.
6. Twist the light body to adjust the vertical angle [adjust].

Diagram Description: Illustrates Method 1: bracket installation onto saddle rail using Allen key ([clockwise] tightening). Method 2: attaching the light to the bracket ([install], [click]) and releasing it ([release]). Shows adjusting the light angle.

Warning ⚠️

• Understand country lighting laws and regulations before use.
• Do not shine directly in the eyes.
• Light may get hot when in use.
• Adjust the angle downward to prevent blinding oncoming vehicles on the public roads.
• Do not submerge the battery or the whole light into water.
• Do not dismantle the light, which will void warranty.
• Do not leave the light on and unattended.
• Keep the light away from fire and combustible materials.

Warranty

MOON Lights are covered by a ONE YEAR LIMITED WARRANTY from the date of purchase, free from defects in material and workmanship. This warranty does not apply to damage due to heat, physical damage resulting from abuse, neglect, improper repair, improper fit, or alterations of the fixture. This covers the lights and cables only. Batteries are covered by 120 days warranty, not including battery normal wear.

All customers should contact the local dealer or regional distributor for warranty service. To make a claim, first contact the original dealer or distributor. Some issues may be resolved upon the initial call. If return of the product is necessary, use a traceable method such as FedEx or UPS. MOON is not responsible for lost or misdirected packages.

Please include your full contact information (name, address, phone number, and email [if applicable]), and a description of the issue.

For more information please contact us at cs@moon-sport.com.

Online Warranty Registration

Visit the following link for online warranty registration: www.moon-sport.com/warranty