dBTechnologies IG5TR Quick Start User Manual

Main Features

• Impressive sound pressure
• New powerful amplifier
• Digital steering
• AURORA Net remote control
• Stack and fly use (with dedicated accessories)

Package Contents

The box contains:

• 1 x IG5TR loudspeaker
• 1 x mains cable
• 1 x rain cover
• This quick start and warranty documentation

Description

The INGENIA IG5TR is a powerful 2-way active vertical speaker, equipped with one compression driver (3" v.c., 1.4" exit) and three 10" woofers, in an innovative shape. The wave guide of the driver is vertically asymmetrical, for precise acoustical coverage in various installation types, indoor and outdoor. The new powerful amplifier section, capable of handling up to 1600 W (RMS power), is controlled by a DSP, which allows detailed customization of the output sound. The DSP can recognize if two INGENIA IG5TRs are installed together, stacked or flown, through special IR communication ports, and perform digital steering, making them sound as one single source with selectable inclination.

Accessories

• GSA-IG5TR: mounting adapter
• DRK-IG5TR: flybar

Specifications

I/O and Control Panel

The amplifier of IG5TR is controlled by a powerful DSP. All connections and controls are in the rear amplifier control panel.

• 1- RDNet Data In / Data Out
• 2- OLED display
• 3- Balanced audio input and output link
• 4- Status LEDs (Signal, Status, Peak)
• 5- C-type USB port for firmware update
• 6- Push rotary encoder
• 7- Full-range Mains input
• 8- Mains Link output

Power Supply Specifications (Power Absorption):

• Draw at 1/8 of full power in average use conditions: 1 A (230Vac) - 1.9 A (115Vac)
• Draw at 1/3 of full power in heavy use conditions: 2.2 A (230Vac) - 4.4 A (115Vac)
• Power absorption with speaker turned on without signal (idle): 0.22 A (230Vac) - 0.47 A (115Vac)

Installer Notes: The values refer to 1/8 of full power, in average operating conditions (music program with infrequent or no clipping). It is recommended to consider them the minimum sizing values, for any type of configuration. The values refer to 1/3 of full power, in heavy operating conditions (music program with frequent clipping or activation of the limiter. We recommend sizing according to these values in case of professional installations and tours.

Mechanics

Handles

On each side of the loudspeaker, there are two handles for easy handling (A).

Mechanical Fixing Point

On each side, there are two mechanical fixing points (B) for stacked and flown configurations, using dedicated accessories.

LP-1 Bracket

Also included is one LP-1 bracket (C), already mounted in the dedicated housing in the back of the loudspeaker. This accessory allows stacking up to n°2 IG5TR loudspeakers.

IR Port

On the top of the loudspeaker, there is an IR port (D) for speaker communication in case of 2-speaker configurations.

Configurations

The following configurations are supported:

1. Stacked configuration: IG5TR, GSA-IG5TR mounting adapter, IGS1 subwoofer
2. Stacked configuration: IG5TR, GSA-IG5TR mounting adapter, IGS2 subwoofer
3. Flown configuration: DRK-IG5TR, 2x IG5TR, 2x LP-1

For multiple-speaker configurations (stacked or flown):

• The upper speaker must be mounted upside down to maintain correct sound coverage.
• Once the DSP recognizes 2 IG5TRs via infrared handles, it acts as a custom delay line on the transducers to direct the final acoustical coverage of the speakers (Steering). This parameter can be set from the speaker display.

For more information about allowed configurations, please refer to the accessories user manual.

Turn On and I/O Settings

Audio Signal Connection

Connect the audio source to the input socket (6). To link the audio signal to another loudspeaker, use an XLR cable. Connect the Output Link (5) of the first speaker to the balanced Input of the second one, and so on.

Power Connection

Plug the mains POWERCON TRUE1 cable (supplied) into the related input (8) to turn on the system. To supply power to another speaker, connect the Mains Link output (9) of the first speaker to the Mains Input of the second one, and so on. Refer to the “TECHNICAL SPECIFICATIONS” or “CONNECTIONS” sections in the INGENIA IG5TR user manual for information on how many modules can be connected in a linked system.

Remote Control Connection

For remote control, connect the Data Input of the loudspeaker to the hardware remote controller (RDNet Control 2 or RDNet Control 8) using etherCON connectors. Connect the Data Output of the first loudspeaker to the Data Input of the second one, and so on. Please refer to the RDNet Control 2 or RDNet Control 8 user manuals for further information.

Setup

The internal DSP allows for easy installation and quick configuration of the IG5TR. Settings saved on the loudspeaker are stored for future use, even after the loudspeaker is turned off. All system parameters shown on the display can be edited by rotating and pressing the encoder.

Main Menu Options:

• Preset: Save and load up to 3 custom presets, load the factory preset, or load a preset from AURORA Net.
• DSP: Set acoustical data (Gain, Delay, High Pass Filter), steering, and beam value.
• Settings: Set detection mode, activate display standby, adjust display brightness, and set ambient temperature.
• Info: View amplifier temperature (Status), loudspeaker Model, firmware, and bootloader versions.
• Reset: Delete all user presets and restore factory defaults.

Important Notes and Warnings

EMI Classification

According to EN 55032 and 55035 standards, this is a Class B equipment, designed and suitable for residential environments.

FCC Class B Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

General Warnings

• WARNING: Make sure the loudspeaker is securely installed in a stable position to avoid injuries or damages.
• For safety reasons, do not place one loudspeaker on top of another without proper fastening systems.
• Before hanging, check all components for damages, deformations, or missing parts that may compromise safety.
• If using outdoors, avoid spots exposed to bad weather conditions.
• Contact AEB Industriale s.r.l. for accessories. AEB Industriale s.r.l. is not responsible for damages caused by inappropriate accessories.
• Features, specifications, and appearance are subject to change without notice. dBTechnologies reserves the right to make changes or improvements without assuming any obligation to change or improve previously manufactured products.

Important Safety Instructions

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. Consult an electrician for replacement of the obsolete outlet if the plug does not fit.
10. Protect the power cord from being walked on or pinched.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer. Use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel.

Additional Safety Instructions

• No naked flame sources, such as lighted candles, should be placed on the apparatus.
• Do not use the apparatus in tropical climates.

General Warnings (Continued)

• Only expert personnel may use the product and its accessories. Ensure the installation is stable and secure. Comply with safety regulations and laws. Periodically check that all parts are in good working condition.
• Only authorized personnel may carry out design, calculations, installation, testing, and maintenance of professional flown or stacked audio systems. AEB Industriale is not liable for improper installation.
• Never suspend the speakers from the handles! Only use specified accessories and configurations.
• Do not obstruct the amplifier cooling fins at the back. Overheating causes gradual reduction of audio volume until the module is thermally stable.
• Do not attempt to open the amplifier.
• In case of malfunction, turn off the power, disconnect the unit from the mains, and contact an authorized service center.
• Only use the power cable provided.
• The USB SERVICE DATA connection is exclusively for firmware updates. Do not connect other USB devices to avoid damage.
• Do not use the loudspeaker for prolonged periods with the limiter LED steadily lit or flashing, as this indicates operation under stress with excessive distortion.
• The loudspeaker shall be powered down after use. Damage caused by leaving the system powered on for extended periods of time while not passing audio is not covered by warranty.
• Periodically check the integrity and functionality of accessories and technical equipment for safe installation.
• Users should never apply a load that exceeds the working load limits of any rigging components or equipment.
• Design, calculation, installation, testing, and maintenance of suspension and stack systems for audio equipment must be performed only by qualified and authorized personnel. AEB Industriale s.r.l. denies any responsibility for improper installations lacking safety requirements.

Contact Information

AEB INDUSTRIALE srl

Via Brodolini, 8
Località Crespellano
40053 VALSAMOGGIA (BO) ITALIA

Tel. +39 051 969870
Fax +39 051 969725
Website: www.dbtechnologies.com
Email: info@dbtechnologies-aeb.com