Marantz Integrated Amplifier PM6005

Welcome

Thank you for choosing a Marantz amplifier. This guide provides step-by-step instructions for setting up your amplifier.

Before You Begin

What's In the Box

• Getting Started: A booklet labeled "Getting Started".
• Owner's Manual: A CD-ROM disc.
• Safety Instructions: A booklet labeled "Safety Instructions".
• Amplifier: An illustration of the Marantz PM6005 amplifier.
• Power cord: An illustration of a power cord.
• Remote control unit: An illustration of a remote control.
• R03/AAA batteries: An illustration of AAA batteries.

If you have setup problems: If you need additional help in solving problems, contact Marantz customer service in your area. For details, see the Marantz homepage: www.marantz.com

Setup

There are six steps to the setup process.

1. Install batteries in the remote control unit
2. Connect the speakers to the amplifier
3. Connect the CD player to the amplifier
4. Plug the power cord into a power outlet
5. Turn the amplifier's power on
6. Begin playback

Step 1: Install batteries in the remote control unit

Instructions:

• Open the battery compartment cover on the remote control unit.
• Insert two R03/AAA batteries, observing the correct polarity (+/-).

Diagram shows a remote control unit with the battery cover open, and arrows indicating the insertion of two R03/AAA batteries with polarity markings.

Step 2: Connect the speakers to the amplifier

Instructions:

1. Peel off about 10 mm of sheathing from the tip of the speaker cable.
2. Either twist the core wire tightly or apply solder to it.
3. Turn the speaker terminal counterclockwise to loosen it.
4. Insert the speaker cable's core wire all the way into the speaker terminal.
5. Turn the speaker terminal clockwise to tighten it.

Diagram shows the rear panel of the amplifier with speaker terminals labeled "SPEAKERS A" and "SPEAKERS B", each with positive (+) and negative (-) connections. It also illustrates preparing speaker cables (stripping, twisting/soldering), loosening terminals, inserting wires, and tightening terminals.

Step 3: Connect the CD player to the amplifier

Instructions:

• Connect the "AUDIO OUT" terminals (L and R) of your CD player to the "AUDIO IN" terminals labeled "CD" on the amplifier using appropriate audio cables.

Diagram shows the rear panel of the amplifier with "AUDIO IN" terminals for TUNER, CD, and NETWORK RECORDER. It also shows a CD player with "AUDIO OUT" terminals (L and R). Lines connect the CD player's audio outputs to the amplifier's CD audio inputs.

Step 4: Plug the power cord into a power outlet

Instructions:

• Connect the supplied power cord to the "AC IN" socket on the rear of the amplifier.
• Plug the other end of the power cord into a household power outlet (AC 230 V, 50/60 Hz).

Diagram shows the rear panel of the amplifier with the "AC IN" socket. A power cord is shown connecting to this socket and then plugging into a standard household power outlet.

Step 5: Turn the amplifier's power on

Instructions:

1. Reduce the volume to the minimum level using the VOLUME knob.
2. Press the power operation button.

Diagram shows the front panel of the amplifier with the VOLUME knob and POWER button highlighted. Insets show a hand turning the VOLUME knob to MIN and pressing the POWER button.

Step 6: Begin playback

Instructions:

1. Set the input source to "CD" using the INPUT SELECTOR knob.
2. Play the CD player.
3. Adjust the volume using the VOLUME knob.

Diagram shows the front panel of the amplifier with the INPUT SELECTOR and VOLUME knobs highlighted. Insets show a hand turning the INPUT SELECTOR to CD, a CD player playing music, and a hand adjusting the VOLUME knob.

Owner's Manual

The included CD-ROM contains an Adobe PDF version of the full owner's manual for the amplifier. Please reference this manual for more details about the setup and operation of the amplifier and its features.

To access the full manual:

1. Insert the CD-ROM into your PC.
2. Follow the on-screen prompts or double-click the PDF file to open it.