Instruction Manual for Z-WAGZ models including: ZW-MFD2, ZW-MFD2 OBD2 Module Adapter, OBD2 Module Adapter, Module Adapter, Adapter
ZW-MFD2 (Z-WAGZ) - ZZ-2
Plug & Play, OBD2/CANControlled, OE Light Flash Module Thank you for purchasing a genuine Z-WAGZ kit, the simplest OBD2-module for flashing OEM lights with a press of a button. This unit comes pre-programmed with 8 different light patterns, some for halogen systems & some for LED systems see below for full operation information including on-board LED status. Optional I/O Button Harness STAR Harness (DODGE/RAM /JEEP ONLY) Operation: 1. For FORD/Lincoln vehicles, connect the Z-WAGZ unit to the OBD2 port and proceed to step (2). For All other vehicles, follow installation instructions on page 3, then return here for operation information. 2. Turn Ignition ON (Ignition must be on for proper operation). Leave vehicle in Park. 3. To activate Z-WAGZ: o Press and HOLD the high beam lever (5 sec) OR o Press and HOLD the provided push button (3 sec) OR o Send a 12v (+) signal to the blue wire (designed to be extended for OE up-fitter switches) Pattern 1 will begin to flash. Once pattern 1 begins, the hazards in the gauge cluster will blink 1 time, indicating Pattern 1 has been selected and the LED on the unit will blink BLUE. See chart for remaining pattern color indication. 4. To switch to Pattern 2: (Pattern 1 must be currently active) o Engage either turn signal, then press and HOLD the high beam lever once more (5 sec). OR o Press & release the provided push button The hazards will blink twice indicating Pattern 2 has been selected. Repeat this process to switch to the next pattern. 5. To deactivate Z-WAGZ: o Press and HOLD the high beam lever OR o Press and HOLD the provided push button OR o Release 12v (+) signal to the blue wire (if connected this way) NOTES: · Vehicles equipped with LED lights should use LED patterns (1-4). Vehicles equipped with standard bulbs should use bulb patterns (5-8) · For FORD, `Drive Mode' (anything outside of PARK gear) will emit its own, separate pattern from whatever pattern is currently selected. This is a limitation of the vehicle and how light data is handled when not in PARK gear. · Not all lights on the vehicle are necessarily used, some lights are not controllable via OBD CAN data. · Z-WAGZ will retain the last used pattern, even after being disconnected from the OBD2 port. · When in Drive Mode, turn signals, headlights & reverse lights will override pattern flashing, until turned off again. · For FORD (only), pattern 4 is an `Alternative Mode' pattern. Some vehicles do not respond to typical data, therefore this pattern method was created. Confirmed Vehicles*: MAKE Ford Lincoln Dodge Jeep MODEL Expedition F150 F250 F350 MKC Challenger Charger Durango Journey RAM 1500 Grand Cherokee YEAR 2018 2013-2019 2016-2019 2016-2019 2019 2018-2018 2013-2018 2016 2019 2019-2023 2018 *Vehicles on this chart have been tested to function properly. More models will be added over time. Other vehicles not listed here may still function. FORD Installation For Ford vehicles, simply connect to the OBD2 port (beneath driver's dash). If desired, connect provided I/O Button Harness to the 4-PIN port on the side of the MFD module and extend push button to a driver-accessible location. Wire triggers are also available for activation (input - blue) or for controlling an external device (output yellow). See below for further information. Return to page (1) for operation instructions. OBD Port 555 S Pompano Pkwy, Pompano Beach, FL 33069 | 929-220-1212 2|Page RAM, Dodge, Jeep, Chrysler Installation 1. Locate the factory STAR diagnostic bank (CAN-C `instrument cluster CAN'). For all RAM trucks, this is located high in the driver's side dashboard. There will be 2 banks in a similar location (Diagram 1). NOTE: other vehicles may have a different location for the STAR bank. Contact ZZ-2 for more information. 2. The proper bank to use is GREEN with WHITE plugs. There will be many, open 2-PIN connectors. Connect the provided 2-PIN plug to any open space on this bank (Diagram 2). 3. Next, Connect power (red) & ground (black) from the RAM-STAR harness to the factory OBD2 port at pin 4: Ground (-) and pin 16: 12v (+) (Diagram 3). 4. The ZWAGZ unit does not connect to the factory OBD port for this install connect it to the provided, white OBD plug (just completed connecting to the vehicle). 5. Optional: tie up the harness using a wire-tie to an existing OEM harness to complete the installation. 6. See to page (1) for operation instructions. Diagram 1 Diagram 2 POWER (+) Diagram 3 GROUND (-) 555 S Pompano Pkwy, Pompano Beach, FL 33069 | 929-220-1212 3|Page LED Status (ALL vehicles) Description Initial Wake Up Unit recognizes CAN bus Unit detects ACC info Unit detects GEAR info Unit detects HIGH BEAM press OR External button press No response from vehicle/CAN Description Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8 Current Draw Active: Current Draw idle: Trigger wire act: Trigger wire idle: Current limit: START-UP INDICATION LED Status Blinks BLUE (1 time) Blinks BLUE (3 times) Blinks GREEN (1 time) Blinks VIOLET (1 time) Solid GREEN Solid OR Blinks RED PATTERN INDICATION LED Status Blinks BLUE Blinks GREEN Blinks RED Alternates GREEN & BLUE Alternates GREEN & RED Alternates BLUE & RED Alternates VIOLET & GREEN Alternates LIGHT BLUE & RED POWER CONSUMPTION 100mA MAX 4mA MAX 0V 5V 10mA More Information Upon connection to OBD port Upon connection to OBD port Upon Turning Ignition ON Upon switching gears Upon pressing High Beam lever or provided push button While connected to OBD and Z-WAGZ activated More Information LED PATTERN LED PATTERN LED PATTERN ALT MODE (FORD) BULB PATTERN BULB PATTERN BULB PATTERN BULB PATTERN 555 S Pompano Pkwy, Pompano Beach, FL 33069 | 929-220-1212 4|PageMicrosoft Word for Microsoft 365