Aqara Single Switch Module T1 (With Neutral)

Product Overview

The Aqara Single Switch Module T1 (With Neutral) is a relay control module based on the Zigbee 3.0 wireless communication protocol. It allows for the control of lights, fans, and other devices. When used with an Aqara Hub, it enables remote control via the app, scheduled on/off operations, power consumption detection, energy usage statistics, and integration with other Aqara devices in scenes.

Key Requirements

• This device requires a compatible Zigbee 3.0 Hub.
• An Aqara Hub is required for HomeKit functionality.
• This product is for indoor use only.

For more details, visit www.aqara.com/support.

Device Indicators and Controls

The module features the following:

• Indicator Light: Shows the status of the device.
• Button: Used for manual control and pairing.
• Antenna: For Zigbee communication.

Button Functions

• Single Press: Turn On/Off.
• Long Press (8 seconds): Reset / Pair to network.
• Triple Press: Effective range test.

Note: If an external switch is connected, turn it on and off 5 times consecutively to enter pairing mode with the Aqara Hub.

Warnings and Precautions

• Do not cover the device while it is operating.
• Ensure the main power switch is turned off before disconnecting the device.
• Do not wire the device in series.
• This product is not a toy. Keep it out of reach of children.
• This product is intended for indoor use only.
• Do not use in damp or outdoor environments.
• Avoid moisture and do not pour water or other liquids onto the product.
• Do not place the product near heat sources.
• Ensure adequate ventilation in enclosed spaces; do not place in sealed compartments without proper ventilation.
• Do not attempt to repair the product yourself. All repairs should be performed by an authorized professional.
• This product is intended to enhance home living and provide device status reminders. The manufacturer is not responsible for any risks or losses incurred due to user non-compliance with the product's instructions.

Installation

Pre-installation Checks

Before installation, ensure the main power switch is turned off!

After the device is powered on, all wires (including the antenna) may be connected to the mains electrical installation. Ensure the product is securely installed in a protected environment inaccessible to hands, such as a switch socket or protective lamp cover.

Do not overload the device. Before powering on, ensure the 10A overcurrent protection switch preceding this product is functioning correctly. Recommended wire stripping length for terminal connections: 6~8 mm.

Wiring Methods

Connect the wires according to the requirements using one of the following methods:

Method 1: Standard Single Switch Wiring

L1 is connected to the wire leading to the load. S0 and S1 are connected to the two terminals of an external switch. L is connected to the live wire, and N is connected to the neutral wire.

Method 2: External Switch Wiring

L1 is connected to the wire leading to the load. One terminal of the external switch is connected to S0, and the other terminal is connected to the live wire (L). L is connected to the live wire, and N is connected to the neutral wire.

Method 3: Dual Control Wiring

L1 is connected to the wire leading to the load. If the external switch is a dual-control switch, the terminal of the original switch that was connected to the load wire can be connected to S0 to achieve external dual control. L is connected to the live wire, and N is connected to the neutral wire.

Note: The maximum wire cross-sectional area is 2.5 mm².

If no external switch is connected, S0 and S1 can remain idle, and the device can be controlled via automation or the app.

Module and Antenna Installation

The module is designed to be securely built into the device (e.g., a pendant lamp or a switch electrical box) to prevent accidental contact.

Antenna Installation:

• The internal antenna wire is connected to the mains electricity. Do not touch it if it is damaged; replace or repair it promptly. Avoid placing the antenna in environments where it could be touched in daily life.
• When the Aqara module is installed in a switch electrical box, it is recommended to attach the antenna to the side wall of the plastic electrical box, parallel to the wall. If the switch console is made of plastic, the antenna should be no more than 10 mm from the wall. If the switch panel console is made of metal, the antenna should be more than 15 mm from the metal console.
• If the module is installed in a metal conduit, it is recommended to place the antenna inside a plastic electrical box.
• When attaching the antenna, try to avoid metal, wires, and the module itself. If installed on the ceiling or inside lights, the antenna should avoid excessive shielding.
• Do not press, bend, or pull the antenna forcefully, as this may damage it.

After installation, turn on the main power switch and press the button on the module or the external switch. If the device can be turned on/off normally, it is functioning correctly.

Quick Installation and Setup

1. Before activating the accessory, ensure you have downloaded the Aqara Home app and installed the Aqara Hub.
2. Open the app, tap on "Home", and then tap the "+" icon in the top right corner to enter the "Add Device (Accessory)" page. Select "Single Switch Module T1 (With Neutral)" and follow the on-screen instructions to add it.

Troubleshooting: If pairing fails, move the module closer to the Hub and try again.

Range Test

Quickly press the button on the accessory three times. If the Hub provides an audible confirmation, it means the accessory can communicate effectively with the Hub.

Indicator Light Status

Technical Specifications

• Model: SSM-U01
• Dimensions: 42.9 × 40 × 19.9 mm, 1.69 × 1.57 × 0.84 inches
• Wireless Protocol: Zigbee 3.0
• Electrical Rating: 100-250 VAC, max. 10 A, 50/60 Hz, max. 2500 W (resistive load)
• Operating Temperature: 0 - 35 °C, 32 °F - 95 °F
• Zigbee Operating Frequency: 2405-2480 MHz
• Max Zigbee Output Power: ≤13 dBm
• Online Customer Service: www.aqara.com/support
• Manufacturer: Lumi United Technology Co., Ltd. Address: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China.

Note: Under normal usage conditions, this device should maintain a distance of at least 20 cm between the antenna and the user's body.

Regulatory Information

FCC Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with a minimum separation distance of 20 cm between the radiator and the user's body.

CE Declaration

LUMI UNITED TECHNOLOGY CO., LTD hereby declares that the radio equipment type is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.lumiunited.com/DoC. This product can be used in all EU member states.

Recycling (WEEE)

This product is marked with the selective sorting symbol for Waste Electrical and Electronic Equipment (WEEE). This means that this product must be handled according to European Directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.

The symbol for "ENVIRONMENTAL PROTECTION - Waste electrical products must not be disposed of with household waste. Recycle at relevant existing facilities. Your local authority or retailer will provide information on recycling." indicates compliance with the European Union directive on "Restriction of Hazardous Substances", which protects the environment by limiting certain hazardous materials and products.

The Bluetooth® trademark and logo are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by Lumi United Technology Co., Ltd. is under license. Other trademarks and trade names are the property of their respective owners. Under normal conditions, this device should maintain a minimum distance of 20 cm between the antenna and the user's body.