Mi True Wireless Earphones 2 Pro User Manual

Introduction

Before use, please read this manual carefully and keep it for future reference.

Product Overview

Diagram showing the charging case with labels for Indicator, Function Button, and USB-C Charging Port. A separate diagram shows an earbud with labels for Touch Button, Secondary Microphone, and Primary Microphone.

Charging Case

• Indicator ?: Shows charging status and battery level.
• Function Button ?: Used for pairing and reset operations.
• USB-C Charging Port ?: For wired charging.

Earbuds

• Touch Button ?: Controls playback, calls, and voice assistant.
• Secondary Microphone ?: Used for calls and noise cancellation.
• Primary Microphone ?: Used for calls.

Illustrations of the product, accessories, and user interface in the user manual are for reference purposes only. The actual product and functions may vary due to product enhancements.

Package Contents

Diagram showing the contents of the package: a charging case, two earbuds, a user manual booklet, a USB-C charging cable, and several ear tips of different sizes.

• Charging Case
• Earbuds (Left and Right)
• User Manual
• USB-C Charging Cable
• Ear Tips (various sizes)

Usage Instructions

Charging ?

• Charging the Earbuds: Place the earbuds into the charging case. They will begin charging automatically.
• Charging the Charging Case: Charge the charging case using the USB-C cable or place the charging case on a compatible wireless charging pad with the indicator facing up. The charging indicator on the case will light up during charging and turn off when fully charged.

Battery Status Check

• Earbud Battery Status: After connecting the earbuds to your phone, you can check the earbud battery status on the phone's status bar. (Note: The phone's status bar always displays the battery level of the earbud with the lowest charge. This feature is not supported by all phones.)
• Charging Case Battery Status: Open the charging case lid or press the function button if the lid is closed:
  • When the charging case indicator lights up for 5 seconds, it means the battery is sufficiently charged.
  • When the charging case indicator blinks, it means the battery is nearly depleted and needs to be charged immediately.
• Battery Status Check via Mi Phone: After successful connection, place earbuds in the case and close the lid. Ensure Bluetooth is enabled on your Mi phone. Hold the phone near the charging case and open the lid. A notification will appear on the phone, showing the battery status of both earbuds and the case. (Note: Ensure your Mi phone is updated to the latest stable version. This feature is currently supported by select Mi phones only.)

Powering On

The earbuds turn on automatically when the charging case lid is opened.

Sleep Mode

Place the earbuds back into the charging case and close the lid. The earbuds will disconnect and automatically enter sleep mode.

Wearing

Remove the earbuds from the charging case and insert them into your ears, noting the L (left) and R (right) markings.

Note: After use, place the earbuds back into the charging case. This prolongs their lifespan and helps prevent loss.

Connection

Pairing with a New Device

1. Place the earbuds in the charging case, then press and hold the function button for 2 seconds. The charging case indicator will blink, indicating the earbuds are ready for pairing.
2. Turn on Bluetooth on your device, search for "Mi Earphones 2 Pro", and connect. If a passcode is required, enter "0000".

Note: Before first use, place the earbuds in the charging case and activate them by pressing and holding the function button for 5 seconds. After activation, the earbuds will automatically enter pairing standby mode.

Connecting with Mi Phones

Place the earbuds in the charging case and close the lid. Ensure Bluetooth is enabled on your Mi phone. Hold the phone near the charging case and open the lid. Follow the on-screen prompts on your phone to connect to the earbuds.

Note: The quick connect feature is currently supported by select Mi phones only. Please update your phone to the latest stable version.

Connection Interrupted

If your device is out of range or Bluetooth is disabled, the earbuds will automatically enter pairing standby mode. If they do not connect to any device within five minutes, they will enter sleep mode.

Automatic Reconnection

When the earbuds are in the charging case, opening the lid will automatically connect them to the last used Bluetooth device. If they do not connect within five minutes, they will enter sleep mode.

Note: If the earbuds cannot connect automatically, you may need to manually connect them via your device's Bluetooth settings.

Clearing Pairing History

1. Place the earbuds in the charging case.
2. Press and hold the charging case function button for at least 10 seconds until the indicator light blinks.

The earbuds will be reset, pairing history cleared, the charging case indicator will blink, and the earbuds will re-enter pairing mode.

Note on Bluetooth Interference: Due to the nature of Bluetooth 2.4GHz signal connections, occasional disconnections or audio dropouts may occur in environments with high electromagnetic interference.

Functions Overview

Incoming Calls ?

• Double-tap on either earbud: Answer / End call.

Music ? and Voice Assistant

When wearing both earbuds:

• Double-tap on the right (R) earbud: Play / Pause music.
• Double-tap on the left (L) earbud: Activate voice assistant.
• Press and hold on either earbud: Cycle through Noise cancellation enabled > Transparency mode > Wind noise cancellation > Noise cancellation off.
• Remove an earbud: Music pauses automatically.

When wearing a single earbud:

• Double-tap on the earbud: Play / Pause music.

Notes:

1. The voice assistant function is only available if your device supports it and has granted permission.
2. If using only the left earbud, place the right earbud back into the charging case and close the lid.
3. Noise cancellation is not available when using a single earbud.
4. Wind noise cancellation mode reduces wind noise during noise cancellation.

Specifications

WEEE Information

Products marked with this symbol are Waste Electrical and Electronic Equipment (WEEE Directive 2012/19/EU) and should not be mixed with general household waste. Protect human health and the environment by returning your waste equipment to a designated collection point for recycling. Proper disposal and recycling help prevent potential negative consequences for the environment and human health. Contact your installer or local authorities for more information on collection points.

Compliance and Safety

Tiinlab hereby declares that the radio equipment type TWSEJ10WM is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: http://www.mi.com/global/service/support/declaration.html

⚠️ WARNING: To avoid the risk of fire, connect the product to a power source whose output complies with PS1 requirements defined in IEC/EN/UL 62368 (output power less than 15 W).

Safety Precautions

• Do not expose batteries or accumulators to excessive heat, such as sunlight, fire, or similar.
• Replacing the battery with an incorrect type may compromise protection (e.g., cause ignition, explosion, or leakage of corrosive electrolyte).
• Disposing of a battery in fire or a hot oven, or mechanically crushing or cutting a battery, may result in an explosion.
• Leaving a battery in an environment with extremely high temperatures may result in an explosion or leakage of flammable liquid or gas.
• Exposure of a battery to extremely low air pressure may cause an explosion or leakage of flammable liquid or gas.
• If the battery is replaced with an incorrect type, there is a risk of explosion.
• Dispose of used batteries according to instructions.
• The maximum operating temperature of the product is 40°C.

General Information

To prevent possible hearing damage, do not use this product at high volumes for extended periods.

The symbol ⎓ indicates DC voltage.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Xiaomi Inc. is under license. Other trademarks and trade names are those of their respective owners.

The Qi logo is a trademark of the Wireless Power Consortium.

Manufactured for: Xiaomi Communications Co., Ltd.

Manufacturer: Tiinlab Corporation (a Mi Ecosystem company)

Address: No. 3333, Liuxian Avenue, Tower A, 35th Floor, Tanglang City, Nanshan District, Shenzhen, China

For more information, visit www.mi.com

Importer: Beryko s.r.o.

Address: Na Roudné 1162/76, 301 00 Plzeň

Website: www.beryko.cz