Fujitsu SR-S Series Product Specifications
This document outlines the specifications for the Fujitsu SR-S Series network switches, including models SR-S324TL2, SR-S318TL3, SR-S310TL3, and SR-S324PS1.
Basic Interface and Performance
| SR-S324TL2 | SR-S318TL3 | SR-S310TL3 | SR-S324PS1 | |
| Product Name | SJ324TL214 | SJ318TL314 | SJ310TL314 | SJ324PS114 |
| Basic Interface | 10/100/1000BASE-T (24 ports, EEE compliant) | 10/100/1000BASE-T (18 ports, EEE compliant) | 10/100/1000BASE-T (10 ports, EEE compliant) | 10/100/1000BASE-T (24 ports, EEE compliant) |
| Optional Interface | 1000BASE-SX/LX/BX-U/BX-D/ZX (4 SFP ports) | 1000BASE-SX/LX/BX-U/BX-D/ZX (2 SFP ports) | 1000BASE-SX/LX/BX-U/BX-D/ZX (2 SFP ports) | 1000BASE-SX/LX/BX-U/BX-D/ZX (4 SFP ports) |
| Switching Capacity (bps) | 48 Gbps | 36 Gbps | 20 Gbps | 48 Gbps |
| Max Packet Forwarding Rate (PPS) | 35.7 Mpps | 26.78 Mpps | 14.89 Mpps | 35.71 Mpps |
| MAC Address Table Size | 8,000 | 8,000 | 8,000 | 8,000 |
Interface Specifications
| Category | Item | Details |
| PoE Function (IEEE802.3af/IEEE802.3at) | PoE Support | Supported (Ports 1-24) |
| Power Supply Capacity | 370W | |
| VLAN Support | VLAN Function | Supported (Port VLAN / IEEE802.1Q Tag VLAN / Protocol VLAN) |
| Max Defined VLANs | 4,094 | |
| Network Authentication | Supported Authentication | ARP Authentication, MAC Address Authentication, IEEE802.1X Authentication, Web Authentication |
| Spanning Tree | Supported Protocols | STP (IEEE802.1D) / RSTP (IEEE802.1w) / MSTP (IEEE802.1s) |
| Link Aggregation | Supported Modes | Static / LACP |
| Layer 2 Redundancy | MLAG Support | Supported |
| Loop Detection | Supported | Supported |
| Storm Control | Supported Control Types | Broadcast / Multicast |
| Supported Control Methods | Port Blocking / Traffic Limiting | |
| QoS Function | Priority Control Conditions | IEEE802.1p (COS) / TOS (IP Precedence) / DSCP / ACL (IPv4, IPv6) |
| Priority Control Method | Strict / WRR | |
| Rewriteable Priorities | IEEE802.1p (COS) / TOS (IP Precedence) / DSCP | |
| ACL (Filtering) | Supported Filters | Layer 2 (Source/Destination MAC Address) / Layer 3 (Source/Destination IPv4, IPv6 Address) / Layer 4 (Source/Destination Port Number) |
| IGMP Snooping | Supported IGMP Versions | v1 / v2 |
| IP Host Function | IP Interface Count | 100 |
| IP Host Function | IPv4 | Supported |
| IP Host Function | IPv6 | Supported |
| DHCP Server Function | IPv4 | Supported |
| DHCP Function | DHCP Relay Agent Function | Supported |
| MAC Address Check Function (IPv4) | Supported | |
| DHCP Snooping (IPv4) | Supported | |
| Port Mirroring | Supported | Supported |
| Wireless LAN Management | Supported Models | Compatible with SR-M20AP1/AP2 |
| Management Features | Automatic transmit power adjustment, Access Point monitoring, Client monitoring, Neighboring Access Point detection, MAC address filter distribution, Channel automatic adjustment |
Maintenance and Management Features
| Category | Item | Details |
| Command Line Interface (CLI) | Supported | Yes (Japanese help available) |
| Web Management | Supported | Yes (Telnet server/client, SSH server) |
| SNMP/RMON | Supported Versions | SNMP v1/v2c/v3 |
| LLDP | Supported Standard | IEEE802.1AB |
| Syslog | Supported | Supported |
| NTP Server/Client | Supported | Supported |
| Configuration Management | Dual Configuration Management | Supported |
| External Media Logging | Supported | Supported (USB memory) |
| External Media Startup | Supported | Supported (USB memory) |
| Config Trial Function | Supported | Supported |
| Port Access Control | Supported | Supported |
| Connected Terminal Limit | Supported | Supported |
| Link Down Relay | Supported | Supported |
| Fan Stop Setting | Supported | Supported |
Physical and Environmental Specifications
| Item | SR-S324TL2 | SR-S318TL3 | SR-S310TL3 | SR-S324PS1 |
| Included Accessories | Power Cable (for AC100V), Other than power cable | Rack mounting brackets (EIA standard compliant) 5, rubber feet, cable strain relief brackets 6, warranty card, "Before You Begin" guide | ||
| Dimensions (W x D x H) | 420 x 250 x 43.5 mm (1U) (excluding protrusions) | 330 x 230 x 43.5 mm (1U) (excluding protrusions) | 266 x 162 x 43.5 mm (1U) (excluding protrusions) | 420 x 400 x 43.5 mm (1U) (excluding protrusions) |
| Weight | 3.5 kg | 3.0 kg | 1.8 kg | 6.4 kg |
| Power Connector Type | AC100V / Parallel 2-pin grounded plug (125V 7A) | AC200V / 2-pin grounded plug (250V 10A NEMA L6-15P) 7 | AC100V | AC100V / Parallel 2-pin grounded plug (125V 7A) |
| Max Power Consumption / Apparent Power | AC100V: 28W / 53VA AC200V: 28W / 67VA | AC100V: 21W / 38VA AC200V: 21W / 46VA | AC100V: 15W / 29VA AC200V: 15W / 35VA | AC100V: 42W / 493.5VA 8 AC200V: 42W / 479.6VA 8 |
| Max Heat Dissipation | AC100V: 100.8 kJ/h AC200V: 100.8 kJ/h | AC100V: 75.6 kJ/h AC200V: 75.6 kJ/h | AC100V: 54 kJ/h AC200V: 54 kJ/h | AC100V: 171.2 kJ/h 8 AC200V: 1692.0 kJ/h 8 |
| Noise Level | 45 dB or less (when fans are operating) | 50 dB or less | 50 dB or less | 50 dB or less |
| Operating Temperature | 0 to 35° C (when fans are stopped) / 0 to 45° C (when fans are operating) | 0 to 35° C (when fans are stopped) / 0 to 50° C (when fans are operating) | 0 to 35° C (when fans are stopped) / 0 to 40° C (when fans are operating) | 0 to 35° C (when fans are stopped) / 0 to 40° C (when fans are operating) |
| Operating Humidity | 15 to 85% RH (non-condensing) | 15 to 85% RH (non-condensing) | 15 to 85% RH (non-condensing) | 15 to 85% RH (non-condensing) |
| Energy Consumption Efficiency | 492W 8 / 493.5VA 8 | 470W 8 / 479.6VA 8 | 15W / 29VA | 42W / 493.5VA 8 |
For energy consumption efficiency details, please refer to the product information on the Fujitsu website: http://jp.fujitsu.com/telecom/
Notes:
- 1: 1000BASE-T and SFP ports are mutually exclusive.
- 2: Mutually exclusive 1000BASE-T ports do not support EEE.
- 3: Priority control rewrite and filtering functions cannot be used simultaneously.
- 4: Compact Flash cards / USB memory (USB2.0 Type-A) are sold separately. For USB memory details, please visit http://fenics.fujitsu.com/products/manual/usb/
- 5: This product does not include screws or cage nuts for rack mounting. Please procure screws suitable for your rack. For Fujitsu racks, refer to http://jp.fujitsu.com/platform/server/primergy/peripheral/rack/
- 6: Bracket to secure the power cable to the unit.
- 7: Supported with the optional 200V power cable (SJ-PWCBL2).
- 8: Values when power supply is active.
- 9: When supplying 15.4W/port, up to 24 ports can be powered. When supplying 30W/port, up to 12 ports can be powered.
