SALUS FC600 Fan Coil Thermostat Quick Guide
Model: FC600
Software Version: 3.6 MCU, 2.7 ZigBee
Introduction
The SALUS FC600 is a versatile thermostat designed for controlling fan coil units in 2-pipe or 4-pipe systems. It manages fan speed and valves to maintain a set temperature. The thermostat can operate in local (Offline) mode without an internet connection, or in remote (Online) mode when connected to the SALUS Universal Gateway (UGE600) and the SALUS Smart Home app. For the full PDF manual, visit www.salus-controls.eu.
Product Compliance
This product complies with EU Directives 2014/30/EU, 2014/35/EU, 2014/53/EU, and 2011/65/EU. The full EU Declaration of Conformity is available at www.saluslegal.com.
Safety Information
Use in accordance with applicable country and EU regulations. For indoor use only. Keep the device dry. Disconnect from power before cleaning with a dry cloth.
Electrical Connections
The FC600 features several terminals for power and control. Below is a description of each terminal:
| Terminal Name | Function |
|---|---|
| L,N | 230V AC power supply |
| V1 | 4-pipe: Heating valve output - 230V AC 2-pipe: Heating or Cooling valve output - 230V AC |
| V2 | 4-pipe: Cooling valve output - 230V AC 2-pipe: Not used (N/A) |
| F1 | Fan Speed control (Low level) - 230V AC |
| F2 | Fan Speed control (Medium level) - 230V AC |
| F3 | Fan Speed control (High level) - 230V AC |
| S1 | Heat/Cool changeover (via external switch) or Pipe Sensor input (only in 2-pipe systems) |
| S2 | Occupancy sensor or External temperature sensor input |
| COM | Common Terminal for sensor/switch |
Wiring Option Diagram
The wiring diagram illustrates how to connect the FC600 thermostat. It shows connections for AC 230V power supply, fan speed outputs (F1, F2, F3), valve outputs (V1, V2), and sensor/switch inputs (S1, S2, COM). The diagram indicates specific wiring for 2-pipe and 4-pipe systems, noting that V2 is not used in 2-pipe systems.
Button Functions
The FC600 thermostat has several buttons for control:
- Increase [⬆️]: Short press to increase temperature or cycle through options. Long press (2 sec) to activate/deactivate Standby Mode.
- Decrease [⬇️]: Short press to decrease temperature or cycle through options.
- Fan Speed [?]: Short press cycles through fan speeds: Low, Medium, High, Auto, Off.
- Mode [?/❄️/?]: Short press selects operating mode: Heating, Cooling, or Eco. Long press (2 sec) enters Programmable Mode.
- M (Digital Mode) [⚙️]: Short press confirms settings or selections. Long press (2 sec) accesses Installer Settings or Time Programming. The exact function can vary based on mode (Online/Offline) and S1/S2 input configuration.
Note: The 'M' button's function can vary based on mode and input configuration.
Display Icons Description
The LCD screen displays various icons to indicate the thermostat's status:
- Auto heat/cool selection [?]
- Schedule icon [?]
- Permanent/temporary override [⏳]
- Fan is running (icon is animated) [?]
- Fan speed (low, medium, high, Auto, OFF) [?]
- Wireless communication with the Universal Gateway [?]
- FC600 is connected to the Universal Gateway and Internet [?]
- Temperature unit (°C/°F) [°C/°F]
- Heating Mode ON [?]
- Cooling Mode ON [❄️]
- Standby mode [?]
- Occupancy/vacancy sensor [?]
- Lock function [?]
- AM/PM indicator [☀️/?]
- Eco Mode [?]
- Day indicator (Mon-Sun) [?️]
- Filter icon (indicates filter cleaning/replacement needed) [?]
- Current time [⏰]
- Sensor indicators (e.g., pipe sensor) [?️]
- Timer icon [⏱️]
- Program number [?]
- S1/COM Sensor indicators [?]
- S2/COM Sensor indicators [?]
- Room/setpoint temperature [?️/?]
- Settings icon [⚙️]
Installation in Online Mode (with UGE600 and Internet connection)
To enable internet control via the SALUS Smart Home app:
- Ensure the Universal Gateway (UGE600) is correctly installed and added to the SALUS Smart Home app. The Gateway's LED should be blue [?].
- In the app, scan for equipment.
- Follow the on-screen instructions in the app to set up the device.
- The device will indicate successful setup and enter Standby Mode [?].
- To activate the thermostat, press the button for 2 seconds [M 2sec] or use the app.
Installation in Offline Mode (without the UGE600 and Internet connection)
To set up the thermostat without an internet connection:
- Press the UP/DOWN buttons [⬆️/⬇️] to select the pipe system: 2-pipe or 4-pipe. Press the confirmation button [M] to save.
- Configure S1/S2 Terminals: Select the relevant setting from the table below based on your system requirements. Press the confirmation button [M] to save.
Terminal Function S1 noFn Manual (no function) S1 HCCO Heat/Cool changeover (external switch) S1 Auto Auto Heat/Cool changeover S1 sens Manual with connected pipe sensor (2-pipe system only) S2 noFn Manual (no function) S2 door Occupancy sensor S2 sens External temperature sensor - Set Operating Mode: Press UP/DOWN [⬆️/⬇️] to select the mode: Cooling [❄️], Heating [?], or Cooling and Heating [❄️?]. Press the confirmation button [M] to save.
- Set Time:
- Press and hold the 'M' button for 2 seconds [M 2sec].
- Press UP/DOWN [⬆️/⬇️] to select the hour format (12/24h) and press [M] to confirm.
- Press UP/DOWN [⬆️/⬇️] to set the hour, then press [M] to confirm.
- Repeat for minutes.
- Set Temperature: Press UP/DOWN [⬆️/⬇️] to set the desired temperature. Press [M] to confirm.
- Installer Settings: For advanced settings, refer to the full manual. (In Online mode, installer settings are available via the SALUS Smart Home app).
- Factory Reset: If needed, follow the instructions to reset the thermostat to factory defaults. This action will permanently erase all custom settings.
- Installation is completed successfully. To launch the thermostat, press and hold the button for 2 seconds [M 2sec].
Switching from Offline to Online Mode
To enable internet control with the UGE600 gateway and SALUS Smart Home app:
- Ensure the UGE600 gateway is installed and connected to your network.
- Follow the steps outlined in the "Installation in Online Mode" section, which involves scanning for equipment in the app and configuring the device.
Important Notes
Standby Mode: The thermostat can be put into Standby Mode [?] by long-pressing the Increase button [⬆️].
Settings Synchronization: When using the FC600 in Offline mode, all configuration settings are automatically saved to the SALUS cloud server. This ensures that you do not need to reconfigure the device when switching to Online mode.
For a full list of parameters, consult the complete manual available at www.salus-manuals.com.
Distributor Information
Importer:
SALUS Controls Plc
Units 8-10 Northfield Business Park
Forge Way, Parkgate, Rotherham
S60 1SD, United Kingdom
Distributor for Poland:
QL CONTROLS Sp. z o.o., Sp. k.
ul. Rolna 4, 43-262 Kobielice, Polska
Exclusive Distributor for Czech Republic:
Thermo-control CZ s.r.o.
Sychrov 2, 621 00 Brno
Czech Republic
Exclusive Distributor for Slovakia:
Thermo-control SK s.r.o.
Podunajská 31, 821 06 Bratislava
Slovakia
Representative for Russia:
OOO "Salus Rus"
115054, Moscow, Ozernovskaya nab., bld. 50, str. 1, off. 301.
Website: www.salus-controls.eu
SALUS Controls is a member of the Computime Group. Maintaining a policy of continuous product development, SALUS Controls plc reserves the right to change specifications, design, and materials of products listed in this brochure without prior notice.
