SONGMICS LPC10 Modular Storage Cube
Assembly Guide & User Manual
Introduction & General Guidelines
Please read the following instructions carefully and use the product accordingly. Keep this manual and hand it over when you transfer the product. This summary may not include every detail of all variations and considered steps. Please contact SONGMICS when further information and help are needed.
The product is intended for indoor use only and not for commercial use. The seller does not assume any responsibility or liability with respect to any damage caused by incorrect assembly or improper use.
It is recommended that two adults assemble the product. Please strictly adhere to the assembly steps.
Notes
- If there are defective or missing parts after unpacking, please contact SONGMICS immediately.
- The accessories are provided according to the parts list. Incorrect assembly may cause insufficient pieces.
- You can assemble according to your own DIY solution. For stability and security, the height should not be more than five times that of the width.
- To reinforce stability, lightly hit the plastic connectors with the mallet (F) included in the package, so that the corner of the panel is firmly inserted into the groove. Do not hit excessively to prevent damaging the product or the mallet.
- Do not shake the assembled structure to ensure its stability.
- The maximum static load capacity of each cube is 10 kg. For safety reasons, the total weight of loaded items should not exceed 80 kg. Please place heavy items on the bottom cubes.
- It is recommended that the product is placed against the wall and on a flat ground. To avoid turning over, please fix this item to the wall with the accompanied security accessories (G). Only use wall plugs and retaining screws that are suitable for your type of wall. Consult local dealers for advice.
- It is prohibited to tread or climb on the product.
- Please replace any damaged part immediately for the sake of safety.
- Do not store food in the plastic cubes.
- Make sure the articles have been well placed to avoid overturning or falling.
- Two persons are needed to move this item and all items should be removed. Do not drag the product abruptly.
- Protect the product from exposure to direct sunlight or rain, and do not touch with sharp objects or corrosive chemicals.
- Do not squeeze or hit the product violently, and keep it away from heat sources and humid places.
- For daily care, please clean with a damp cloth and dry with a soft cloth.
Warnings
- ❗If the item tips over, it may result in serious or fatal injury.
- ❗Never use the product if any part is missing or defective. Otherwise, it can be hazardous.
- ❗Not intended for use by children under 3 years of age. Children must be under adult supervision to use the product.
- ❗Keep children away from the product. There are small parts.
- ❗Do not allow children to climb or play on the product to avoid body injury caused by tilting.
- ❗During assembly, keep small parts out of the reach of children. It may be fatal if swallowed or inhaled.
- ❗To avoid potential danger of suffocation, keep all parts and packaging (films, plastic bags and foam, etc.) away from babies and children.
Parts List
| Part | Description | Quantity |
|---|---|---|
| A | Large Panel | 12 |
| B | Medium Panel | 20 |
| C | Long Panel | 10 |
| D | Long Panel with Hole | 10 |
| E | Plastic Connectors | 48 |
| F | Mallet | 1 |
| G | Wall Mounting Kit (Straps, Screws, Plugs) | 2 sets |
Assembly Instructions
General Assembly Tips:
- Distinguish the front and back of the plastic plates. The side marked with the SONGMICS logo should face outward.
- Ensure all panel corners are fully inserted into the connector grooves.
- Lightly tap connectors with the mallet (F) to reinforce connections.
- Assemble door panels (D) after each layer is finished, not at the very end.
- Reinforce all connectors after assembly is completed.
Step 1: Base Layer Foundation
Attach panel A (45x35cm) to connector E. Ensure the corners of the panel are fully inserted into the grooves of the connector.
Step 2: Adding Side Panels
Attach panels B (35x17cm) to the base connectors to form the sides of the first cube.
Step 3: Adding Back Panel
Attach panel C (45x17cm) to the rear connectors to form the back of the first cube.
Step 4: Adding Top/Shelf Panel
Insert panel A (45x35cm) to serve as the top of the cube or a shelf.
Step 5: Securing Connectors
Secure the structure by pressing connectors E firmly into place.
Step 6: Preparing Door Panel
For door panel D (45x17cm with hole), insert the wire frame into the innermost groove of the connector. The wire should sit at the very bottom of the groove.
Step 7: Door Panel Installation
Continue attaching door panels to the assembled cube structure as shown.
Step 8: Assembling Doors
Assemble the door panels after each layer is finished. Do not wait until the whole unit is assembled.
Step 9: Reinforcing Connections
After assembling each layer, use the mallet (F) to gently but firmly tap the connectors to ensure they are tightly secured.
Step 10: Building Up Layers
Continue adding layers by repeating the process of attaching panels A, B, and D, securing with connectors E.
Step 11: Stacked Cubes
Two cubes stacked on top of each other.
Step 12: Completing the Structure
Repeat the previous assembly steps to build the desired height of the modular storage unit (e.g., the full 10-layer structure shown).
Step 13: Final Reinforcement
Once the entire structure is assembled, use the mallet (F) to lightly and repeatedly tap all connectors from all directions to ensure maximum stability.
Step 14: Wall Mounting for Safety
Important: To prevent tipping, secure the product to the wall using the provided safety kit (G). Attach the straps to the unit and then to the wall using appropriate wall plugs and screws for your wall type. Consult a professional if unsure.
Diagram shows the unit placed against a wall, with safety straps being attached to the top of the unit and then to the wall.
Product Variants & Modularity
The SONGMICS LPC10 is a modular system. You can assemble it into various shapes and configurations according to the illustrations and your own ideas, using the provided panels and connectors. The quantity of parts is sufficient for the illustrated configurations.
Example configurations may include:
- A 2x5 cube arrangement (two cubes wide, five cubes high).
- A 5x2 cube arrangement (five cubes wide, two cubes high).
- Other custom arrangements.
Care and Maintenance
For daily care, please clean the product with a damp cloth and then dry it with a soft cloth.
Protect the product from direct sunlight, rain, sharp objects, corrosive chemicals, excessive heat, and humid environments.
