Autoslide – Autoslide – Automatic Sliding Doors for homes
Installation Guide for AUTOSLIDE models including: AS087HWWS, 2ARVQ-AS087HWWS, 2ARVQAS087HWWS, Wired Hand Wave Sensor, Wireless Hand Wave Sensor
AUTOSLIDE PTY LTD AS087HWWS AUTOSLIDE Wireless Hand Wave Sensor 2ARVQ-AS087HWWS 2ARVQAS087HWWS as087hwws
File Info : application/pdf, 2 Pages, 1.66MB
DocumentDocumentInstalling your AUTOSLIDE Wireless Hand Wave Sensor or AUTOSLIDE Wired Hand Wave Sensor
(LSG0 4.5.22)
The AutoSlide Hand Wave Sensor can be hardwired or wirelessly connected to the AutoSlide unit, and offers effortless tap-to-trigger control. If wirelessly connected, the hand wave sensor will open the door to the full default width, but if hardwired to the unit, it can open the door to a par al pet width (assuming Pet Mode is programmed). Check out our video at:
h ps://vimeo.com/319406044
- Each sensor requires 2x CR2032 ba eries (included)
- Switch on back switches between Inside ("M") and Outside ("S") sensor connec on (see picture on le and info below)
- Approx. maximum trigger distance is 4"to 6" from front surface, depending on brightness of environment
- 4 ,2" (+12 ,3") of cabling included per sensor
Installa on
Wireless Installa on
Hardwired Installa on
1. Slide the panel on the back of the sensor down to release it (note: you 1. Go to the back of the hand wave sensor and locate the opening
don't need to remove the screw at the top to do this).
showing the white port on the sensor's circuit board (ref. Diagram 1).
2. Insert included ba eries into sensor. Each sensor takes 2x CR2032 ba eries (one in each slot; "+" side up, grated side down)
2. Take your included sensor cable and plug it into the white port on the back of the hand wave sensor (ref. Diagram 1).
3. Slide the back panel back into place (make sure to keep the panel's rectangular opening above the white port).
3. Locate on your unit's control panel the ports for "Inside Sensor," "Outside Sensor," & "Pet Sensor" (labeled on the front, ref. Diagram 3).
4. Press the "Sensor Learn" bu on on your unit's control panel. Tap the 4. Take the other end of your sensor cable and plug it into any one of hand wave sensor (it should flash blue on the front). Then, press "Sensor these three ports (see informa on on which port to use below). Learn" again, and tap the hand wave again.
5. The hand wave sensor should now be paired to the unit. Confirm the sensor is ac ve by tapping the front of it - it should flash blue on the front, and open the door.
5. The hand wave sensor should now be connected to the unit. Confirm the sensor is ac ve by tapping the front of it - it should flash blue on the front, and open the door.
Sensor Port Explana on
1. Connec ng the hand wave sensor to the Inside Sensor port will enable it in Green, Red, and Pet Mode. 2. Connec ng the hand wave sensor to the Outside Sensor port will enable it in Green and Pet Mode. 3. Connec ng the hand wave sensor to the Pet Sensor port will enable it in Pet Mode only. 4. Connec ng the hand wave sensor to the Stacker Sensor port will enable it in Blue Mode only.
* Note that, if you wirelessly connect your hand wave sensor, you have the op on of switching between "M" (Inside) and "S" (Outside) channels. Pet Sensor triggering isn't an op on unless the hand wave is hardwired to the Pet Sensor port. If the hand wave is hardwired to a specific sensor port, the hand wave's channel switch is ineffec ve.
AUTOSLIDE LLC - autoslide.com - 833-337-5433
FCC Statement
This device complies with part 15 of the FCC Rules. Opera on is subject to the following two condi ons: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired opera on.
Any Changes or modifica ons not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec on against harmful interference in a residen al installa on. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc ons, may cause harmful interference to radio communica ons. However, there is no guarantee that interference will not occur in a par cular installa on. If this equipment does cause harmful interference to radio or television recep on, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separa on between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.