FOSSIBOT F2400 Portable Power Station

⚠️ Precautions for Use

1. Please avoid long-term storage and use of this product in environments with high temperature and humidity or direct sunlight to avoid shortened battery life and other failures. The product should not be close to the fire source ?, otherwise it may cause a major fire or accident.
2. This product must not be disassembled or modified. Improper operation may cause product malfunction or even fire ?.
3. Be careful not to drop or drop the product from a high place, so as not to damage ⚠️ the product.
4. Please store or use this product out of the reach of children ?, otherwise the product may be dropped or collided and may cause bodily injury to children ?.
5. Please use our original accessories, and Fossibot will not guarantee the defective products caused by the use of non-original accessories.
6. Please directly plug in the wall socket to charge the product, do not use extension cords or cable taps, otherwise there is a risk of damage ⚠️ to the extension cords and cable taps or even a fire ?; If the extension socket is plugged in to charge this product, please do not connect other electrical appliances to this socket, otherwise the household energy meter may trip.
7. When the product is not in use or idle, please turn it off ⚡ and unplug the power cable. If it needs to be idle for a long time, please consume the product from a fully charged state to an uncharged state, then recharge it to about 50% of the battery level and store it. In order to prolong the life of the product, please take three months as a cycle, operate and keep it in this way.
8. If the product reaches scrap conditions, please discard or recycle the product in accordance with local laws.

Thank you for purchasing Fossibot F2400 portable power station. Please carefully read the user manual before operating the product.

This user manual is required for product warranty. Please keep this user manual together with the purchase certificate such as the invoice.

Due to the transportation requirements of international customs for battery products, F2400 is charged to about 30% before delivery. Please fully charge the product after unpacking for use.

This product should be charged directly from the wall socket ?. Do not use extension cords and cable taps. When using two or more sockets to charge, do not use devices other than this product on the same socket.

Product Introduction

This product is a 2048Wh large-capacity 2400W high-power portable power station supplied with 2-hour high-speed charging, using a lithium iron phosphate battery with extremely high safety performance.

It can be used as a backup power supply in the event of a sudden power failure or a disaster, or used for camping and living power in a camper, and can also provide power for various power tools regardless of the occasion.

2400W high power, sine wave AC output, can be used for high-power household appliances such as dryers, microwave ovens, refrigerators, induction cookers and electric ovens; it can also be used for other electronic devices such as personal computers.

0-100% charging can be completed within 2 hours through the 1100W ultra-fast charging of the household power socket, and the input voltage frequency can be auto switched to 50Hz/60Hz, or the input voltage frequency can be manually switched to 50Hz/60Hz. In addition, this product also supports solar panel charging ☀️, and the maximum input power cannot exceed 500W, allowing you to charge outdoors or at home when there is a power outage.

This power station can power various devices, including:

• [TV]
• [Lamp]
• [Speaker]
• [Drone]
• [Kettle]
• [Phone]
• [Fan]
• [Refrigerator]
• [Car]
• [Heater]
• [Meter]

Button Function Introduction

The F2400 portable power station features several buttons and ports for operation. Below is a description of each:

⚡ Power ON/OFF Button

Instructions: Press and hold the power button for 3s to wake up the system, turn on the LCD display, and press and hold again for 3s to turn off.

? LED Light Button

Instructions: Short press the Light button, the LED light is on; short press again, the LED light enters the SOS mode ?, short press in turn, enter the strobe mode ?, and finally the LED light turns off. Long press the LIGHT button for > 1 second, directly turn off the LED light.

? USB ON/OFF Button

Instructions: Short press the USB button to turn on the USB output port, and short press it again to turn it off.

Supported USB ports include: USB-A (QC3.0), TYPE-CX3 (PD-20W), TYPE-CX1 (PD-100W).

⚡ DC ON/OFF Button

Instructions: Short press the DC button to turn on the DC output port, and short press it again to turn it off.

Supported DC ports include: DC output x2 (12V/3A), Cigarette port x1 (12V/10A), XT60x1 (12V/25A).

?️ LCD Screen

Display the product's battery level and usage status tips.

?️ Input Power Knob

When the product is connected to the AC mains for charging, the power can be adjusted according to the actual input voltage. Clockwise rotation increases the input power, and counter-clockwise rotation decreases the input power. Charging this product at low power is beneficial for extending battery life.

? Cooling Suction/Exhaust Port

When the product reaches the temperature threshold set by the system, the cooling fan will automatically run, accompanied by a certain fan noise (fan noise below 60dB is normal). Do not block the cooling suction/exhaust port during use of this product, and do not place any object within the range of 30CM.

? AC Switch (AC output port, the sum of electrical load power should be <2400W)

Tap the AC button to enable the AC output function.

Notices:

1. Since there may be differences in the AC output frequency in different regions, please check the AC voltage and frequency of the device before use.
2. Press and hold the AC button for 2 seconds to enter the frequency switching mode, the 50Hz or 60Hz icon will flash on the display. Short press the AC button again to select 50Hz or 60Hz; when the icon stops flashing and displays 50Hz or 60Hz, it indicates the switch is successful.
3. Short press the AC button 10 times in quick succession in the United States and Japan to switch the AC output voltage to 100V or 110V.

? AC Input and Anderson Port

☀️ Anderson Port

Connect the solar panel using the Anderson to MC4 cable. The input of the solar panel can be up to 500W and the maximum voltage is 50V. If the equipment is damaged by exceeding the maximum voltage, it is outside the scope of warranty.

? AC Input

1100W fast charging with a household socket can perform a 100% charge within 2 hours. This product can directly use the socket on the wall, etc. Please do not use extension cords and cable taps to connect several devices at the same time. Using a cable tap to charge several devices at the same time will cause a large current to flow, causing cable breakage and fire risk ?. Do not use the same socket to connect other devices while charging this product. In general, when the same wiring in the family exceeds 1500W, the safety circuit breaker will start.

? Overload Protection Button

When the power supply current is unstable due to lightning or other reasons, and there is a large current input at the AC Input, in order to protect the product, the overload protection function (safety circuit breaker) will activate and cut off the AC input port.

Please follow the sequence below to restore the AC input function:

1. Turn off the power button ⚡ and unplug all ports.
2. After confirming that there is no abnormality in each part, turn on the power button ⚡.
3. Press the overload protection button, connect the AC cable to restore the AC input.

Introduction of Display Interface

The Screen Displays Precautions

• When this icon ? lights up, please ensure that the vent is not blocked.
• When this icon ⚠️ flashes, it means that the temperature is too high or too low, and the product may turn on the smart protection program and stop working. (Need to wait for the product to return to the normal temperature range to continue working)
• If the icon ? blinks, it indicates that the AC mains connection is abnormal. Check the charging port.
• When this icon ❌ flashes, it means abnormal, please check the load.

UPS Mode

UPS Feature

This product has a bypass mode, which can output directly from AC mains without going through the battery. In the UPS state, when the AC input power of the commercial power is cut off due to a power failure, it can automatically switch to the product battery power supply within about 8 milliseconds to ensure the AC output.

UPS Connection Diagram

In the UPS mode of U. S. and JPN standard, the maximum power of AC output is below 1100W, and if the AC output exceeds 1100W, the " AC output" icon flashes to indicate overload.

In the UPS mode of CN, UK, EU and KR standard, the maximum power of AC output is below 2400W, and if the AC output exceeds 2400W, the " AC output" icon flashes to indicate overload.

Connection of Solar Panels

The company's products can be connected to solar panels and can be charged through the solar panels. The power of the solar panel is 500W, and can fully charge the product within 4 hours. (The input of the solar panel can be maximum 500W, maximum voltage 50V).

The charging power of the solar panel is determined according to the weather and other conditions.

Solar panel voltage exceeding 50V will damage the equipment and may be out of warranty.

Option one: Portable Power Station Charging Area

Option two: Portable Power Station Charging Area

Car Charging

This product uses the ACC charging cable, which can be used for mobile charging by the cigarette lighter (Accessory: hereinafter referred to as ACC) in the car ?.

Before using the product, whether it is charging or discharging, you must open the fan covers on both sides at the same time to prevent the product from being over heated and damaging the product.

Connect the ACC charging cable to the cigarette lighter in the car and the Anderson interface on the side of the product, turn on the engine of the car, and the LED display of this product will display the input power.

Use of Fan Covers

Before operating the product, whether it is charging or discharging, you must open the fan covers on both sides at the same time to prevent the product from over heating and causing the product to stop working or enter a protection state.

Product Specifications

Battery Specifications

Troubleshooting

Warranty

Please fill in all of the above items.

This product comes with a 24-month warranty from the date of purchase.

• If there is a quality problem within the scope of normal use, Fossibot provides warranty.
• After purchasing Fossibot's products, please keep this product together with invoices and other items, and please provide information according to Fossibot's reliance request when maintenance services are required.
• Warranty service may not be provided if the warranty card is damaged, altered, etc., and it is considered to be incorrect, or if the warranty card is not stamped by the store where it was sold.
• Damage caused by use beyond the normal use range is not covered by the warranty service.
• The content of the warranty scope is subject to the content recognized by the company.
• Even within the scope of the warranty, there are times when an equivalent product can be exchanged. Shipping and maintenance costs for products not covered by the warranty shall be borne by the customer.
• Product specifications and features are sometimes changed without prior notice.
• Please refer to Fossibot's updated guideline on their website below.

Manufacturer: Shenzhen Qichang Intelligent Technology Co., Ltd.

Address: China - Shenzhen

Technical service email: support@fossibot.com

Company official website: https://www.fossibot.com