Instruction Manual for ROGUE models including: Echo Rower Bike, Rower Bike, Bike
1 ECHO ROWER IMPORTANT SAFETY INFORMATION WARNING: MISUSE OF THIS CAN RESULT IN SEVERE INJURY. Both Rogue Fitness and buyer disclaim any express or implied warranty, including, without limitation, warranties or merchantability and/ or fitness for a particular purpose with respect to the equipment. Buyer assumes all liability to use of equipment. Rogue Fitness · 545 E 5th Ave. Columbus, Ohio 43201 · Customer Service: 614-358-6190 · Team@RogueFitness.com PARTS AND TOOLS USED 2 STEP 1 3 · TAKE OUT THE FRAME (80) · USE THE WRENCH (S27) IN THE HARDWARE KIT TO REMOVE THE 6 SCREWS ON THE PROTECTION BOARD 80 STEP 2 4 · ASSEMBLE THE END CAP (33) ONTO THE FRAME (80) 33 80 STEP 3 5 · FIX THE TURF TIRE WHEELS (L) AND (R) ONTO THE FRONT FOOT TUBE ASSEMBLY (56) USING M10 HEX NUTS (32) 56 L 32 R STEP 4-1 · SPREAD ROWER APART BY 12 INCHES · INSERT ROUND CROSS BAR OF LEG ASSEMBLY (56) INTO PLASTIC RECIEVER BASE (80) · PUSH ROWER BACK TOGETHER ALL THE WAY UNTIL YOU SEE THE BOLT HOLES OF THE LEGS LINE UP WITH THREADED HOLES OF BASE * RECOMMENDED TO USE TWO PEOPLE FOR THIS STEP 56 6 80 CAUTION PINCH POINT WARNING STEP 4 7 · STAND THE FRAME VERTICALLY · USE THE M8 * 20 (57) HEX HEAD BOLT TO FIX THE FRONT FOOT TUBE ASSEMBLY TO THE FRAME (80) 80 57 57 STEP 5 · FIX THE LEFT (L) AND RIGHT (R) FOOT PEDAL ASSEMBLIES TO THE FRAME (80) USING A 1/4-20 FULL THREAD SCREW (83) (PAN HEAD SCREW) L 83 8 R 83 80 STEP 6 · FIX THE REAR FOOT TUBE ASSEMBLY (108) TO THE FRAME (80) USING 1/4-20 X16MM SOCKET HEAD SCREWS (111) · LOCK IT WITH WRENCH (S27) 9 80 111 108 STEP 7 10 · FIX THE SEAT CUSHION (123) TO THE SEAT BRACKET ASSEMBLY (122) USING A 20MM FULL THREAD (20) SOCKET PAN HEAD SCREW (3/16-24) ·SEE ORIENTATION IN IMAGE FOR CORRECT SEAT ALIGNMENT (123) 20 123 20 122 STEP 8 · HOLD TIRE WITH YOUR FOOT WHEN UNFOLDING THE UNIT BY SEPARATING THE REAR MAIN FRAME ASSEMBLY FROM THE FRONT FOOT TUBE ASSEMBLY · PLACE HORIZONTALLY 108 11 CAUTION | PINCH POINT WARNING KEEP YOUR HANDS CLEAR OF THE HINGE- DO NOT PUT FINGERS ON THE LATCH WHEN CLOSING L CAUTION PINCH POINT WARNING KEEP YOUR HANDS CLEAR OF THE HINGE- DO NOT PUT FINGERS ON THE LATCH WHEN CLOSING STEP 9 12 · FIRST, LIFT THE LATCH HANDLE (94) ALL THE WAY FORWARD UNTIL IT CATCHES ON THE HOOK (98) · PULL THE HANDLE (94) BACK DOWN AND PUSH IT FIRMLY CLOSED. 95 94 98 CAUTION PINCH POINT WARNING CAUTION PINCH POINT WARNING STEP 10 13 · LIFT THE REAR LATCH (95) UP BY HAND, AND THE ENTIRE BUCKLE WILL BE RELEASED, ALLOWING THE FRONT AND REAR FRAMES TO FOLD UP 98 94 95 CAUTION PINCH POINT WARNING CAUTION PINCH POINT WARNING STEP 11 14 · INSTALL THE BATTERIES BEFORE ASSEMBLING THE CONSOLE WITH THE ROWER · REMOVE THE SCREWS AND NUTS FROM THE CONSOLE AND INSTALL THE CONSOLE ONTO THE ROWER · MAKE SURE THE TAB ON THE ROWER GOES INSIDE THE CURVED POCKET OF THE CONSOLE · MAKE SURE THE WIRE CANNOT GET PINCHED *IF THE WIRE CAN BE PINCHED, YOU DO NOT HAVE THE ROWER TAB INSIDE THE CURVED POCKET · TIGHTEN THE SCREWS WITH A WRENCH (S27) · INSERT THE SIGNAL WIRE INTO THE CONSOLE. STEP 12 15 · CHECK TO MAKE SURE THE ROWER IS STABLE, AND FUNCTIONS PROPERLY · ROW EASY AT FIRST TO CONFIRM FUNCTIONAdobe PDF library 17.00 Adobe Illustrator 28.6 (Macintosh)