Pull Down Kitchen Faucet

Installation Instructions

Before Installation

All information is compiled according to the latest published product information. The company reserves the right to change the characteristics, packaging, or type of product available at any time without notice.

This manual contains important information on installation, maintenance, and cleaning. Please provide this information for users to read.

Installation Precautions:

Be sure to flush the water supply pipe thoroughly to remove impurities from the pipe.
If installing a new washbasin, it may be easier to install the faucet first to the washbasin.
Maximum working pressure: 0.5 MPA (5 bar). A pressure relief valve must be installed when water pressure exceeds 0.5 MPa (5 bar).
The highest working temperature and ambient temperature for the shower: 60 °C. Please pay special attention to the arm tube connected with the shower to ensure it is away from the heater, otherwise, it may damage the shower and its seals, or even harm the users.

Instructions for Use

Handwheel switch: Turn right for cold water-mixed water-hot water; return to the middle to close.
Handwheel switch: Turn left for cold water-mixed water-hot water; return to the middle to close.

Use Strategy:

Handwheel switch, turn right cold water-mixed water-hot water, return to the middle off.
Hand wheel to the left rotation of cold water-mixed water-hot water, return to the middle of the closed.
▶️ Draw head free draw.
? Press to switch the shower spray.
? Push the bubbles out of the water.

Installation Dimensions

The following dimensions are provided for installation planning:

Overall faucet height: 423 mm.
Spout reach from the center of the base: 219.5 mm.
Spout height from the base: 185.8 mm.
Base width/diameter: 240 mm.
Recommended mounting hole diameter: Approximately 30 mm to 35 mm.
Surface width for installation: 220 mm (compatible with sink openings of 217 mm).
Center distance for mounting: 150 mm.
Flexible hose length: 60 cm.
Connection thread sizes: M28x1.5 and M32x1.5.

Diagram Description: The diagram shows a side and top view of the faucet with key measurements indicated.

Installation Steps

Follow these steps for proper installation:

Diagram: Mounting washer with rubber ring facing down, handle on the right.

1. The mounting washer (1) is arranged with the rubber ring face down to install the faucet, and the handle is placed on the right side.

Diagram: Screw (2) threaded into mounting ring (3), 6mm exposed.

2. The screw (2) is screwed into the mounting ring (3) until the screw is exposed 6mm to the mounting ring.

Diagram: Gasket (Metal/Plastic) on tooth tube (5), installation ring rotated.

3. The gasket (4) is arranged on the tooth tube (5), and the installation ring is rotated on the tooth tube.

Diagram: Screw position on mounting ring adjusted and tightened.

4. Adjust the screw position on the mounting ring and tighten it.

Diagram: Hose (6) connected to water source. Hose (7) labeled "COLD" for cold water.

5. Connect and lock the hose (6) to the water source. The hose labeled "COLD" (7) connects the COLD water.

Diagram: Hot and cold water turned on and running.

6. Turn on the hot and cold water and let it run for about a minute.

Diagram: Faucet body inserted into water slot following an arrow.

7. Insert the main body of the faucet into the water slot according to the direction indicated by the arrow.

Diagram: Pipe connection from elbow to shower, checking for smooth draw.

8. Draw pipe connection from the elbow into the shower; check whether the draw is smooth.

Diagram: Heavy hammer (9) loosely installed on shower hose (8).

9. The heavy hammer (9) is loosely installed on the shower hose (8).

Diagram: Shower hose connected to faucet hose. Options: Clamp, Snap.

10. Connect the shower hose to the faucet hose.

Diagram: Weight adjusted to position and locked.

11. As shown, adjust the weight to the right position and lock it in place.

Diagram: Weight adjusted to correct position.

12. If necessary, adjust the weight to the correct position.

Maintenance and Cleaning

Faucet Maintenance:

Turn on the faucet and rub the nozzle to remove impurities.
When there are impurities causing water flow to be small, remove the shower frother head and clean it. Reassemble after cleaning.

Check for Installation Results:

Check and make sure all joints are tight and the handwheel is in the closed position. Open the main water supply and drainage system, then check and repair any leaky connections.

Cleaning Instructions:

Apply to all processed surfaces: Wash the coated surface with neutral soapy water, then wipe the entire surface thoroughly with a clean, soft cloth. Many detergents, such as ammonia, detergent, and toilet cleaner, etc., will cause damage to the plating surface; do not use them.

Abrasive cleaning appliances or detergents should not be used on faucets and their accessories.

	Pot Filler Faucet Technical Specifications and Dimensions Detailed technical specifications and dimensional drawings for a wall-mounted, articulated pot filler faucet, highlighting its reach, height, connection size, and 360-degree rotation capabilities for optimal kitchen functionality.
	Kitchen Faucet Dimensions and Specifications Detailed dimensions for a modern kitchen faucet, including height, reach, and spout height, presented in both centimeters and inches for clarity.
	Bathroom Faucet Installation: Single Handle Kitchen Faucet Guide Step-by-step installation instructions for a single handle kitchen faucet, covering water shut-off, faucet mounting, sprayer hose attachment, water line connection, and leak testing.
	Kitchen Faucet Dimensions and Specifications Detailed dimensions for a modern kitchen faucet, including height, width, and spout reach, essential for installation and design planning.
	Gold Finish Pull-Down Kitchen Faucet Dimensions & Specifications Detailed measurements for a modern pull-down kitchen faucet, finished in an attractive gold tone. Key measurements include overall height (48.5cm/19in), spout height (19cm/7.5in), spout reach (16.8cm/6.6in), and base width (25.4cm/10in), aiding in installation and design planning.
	Black Kitchen Faucet with Pull-Down Sprayer - Dimensions and Specifications Detailed dimensions and specifications for a black kitchen faucet featuring a pull-down sprayer, including height, reach, and diameter measurements.
	Black Pull-Down Kitchen Faucet Dimensions and Specifications Provides key dimensions for a modern black pull-down kitchen faucet, including overall height, spout reach, and base measurements for installation planning.
	Kitchen Faucet Installation Manual - Model W-80(ES) Comprehensive installation guide for the W-80(ES) kitchen faucet, including parts list, step-by-step instructions, and warranty information.