Neoeco Airbrush Compressor Kit

Introduction

This Airbrush compressor kit is an ultra-quiet miniature airbrush compressor kit that is ideal for light-use, low-pressure applications with a working pressure of 4-25 psi. This airbrush kit may be used anywhere in the world and comes with a plug adapter suitable for your country. Weighing less than 1 kilogram (2.2 pounds), it is easy to transport. The airbrush holder provides a safe and convenient place to rest your airbrush when you're not spraying. The pressure switch button offers three air pressure settings, allowing you to subtly adjust the air pressure to the perfect amount. Featured with auto start/stop function, the compressor will be action according to the airbrush trigger's action. More smarter and easier to use.

Specifications

Assembly

Follow these steps to assemble your airbrush compressor kit:

1. Connect the air hose to the compressor. (Image: Air hose connected to compressor)
2. Insert the airbrush holder into the compressor. (Image: Airbrush holder inserted)
3. Plug in the power adapter. (Image: Power adapter plugged in)
4. Press the ON/OFF button. (Image: ON/OFF button pressed)
5. Adjust the air pressure mode and start working. (Image: Air pressure adjusted)
6. Press the trigger and pull it back; the airbrush will start working. (Image: Trigger pulled back, airbrush operating)

How to Use the Airbrush

1. Press down on the main lever for air. (Diagram: Lever pressed down for air)
2. Pull the main lever back for painting. (Diagram: Lever pulled back for painting)

Adjust the distance between the airbrush needle cap and the work surface to control spray width. The depth of the trigger pull also affects spray width.

Airbrush Information & Troubleshooting

Applications

This airbrush is designed for industrial products, model spraying, painting, cake decoration, advertising painting, furniture repair, beauty makeup, temporary tattoos, etc.

Specifications

• Fluid cup capacity: 7CC
• Nozzle diameter: 0.3mm

Troubleshooting

Q1: Why does the paint only bubble in the fluid cup but no paint comes out?

Generally, this is caused by the loosening of the nozzle cap (No.2) and nozzle (No.3). Check if the nozzle o-ring or o-ring for nozzle cap (No.4) is missing. The solution is to tighten the nozzle and nozzle cap carefully. If the o-ring is missing, you can temporarily solve it by wrapping raw material tape. Replace the o-ring for long-term use or use special sealant.

Q2: Only air sprays out without paint...

The concentration of the paint affects its fluidity. Solution: Unscrew the tail handles (No.16) and needle chucking nut (No.15). Pull the needle (No.5) back out, reseat it in its original position, and then tighten the needle chucking nut lock nut. Check if the center of the lid is blocked; if so, use a needle to clear it.

Tips

• The spray gun is a precision tool. Test with water first after purchase.
• This product can only spray liquid paint; the liquid should be diluted before use.
• Clean the airbrush immediately after each use to prevent nozzle or needle blockage.

Maintenance & Cleaning

Simple Cleaning

Clean your airbrush after each use and before each color change, or when it becomes clogged, to ensure proper function.

1. Add water or cleaning cleaner into the airbrush cup. The cleaner will loosen and dissolve leftover paint. (Image: Cleaner added to cup)
2. With the airbrush working, cover the airbrush nozzle with your index finger to block airflow. (Image: Finger blocking nozzle)
3. Pull the trigger slightly until small bubbles appear, then flick the button back and forth for cleaning about 8-15 seconds. (Diagram: Trigger pulled, button flicked)
4. Spray the liquid into a washing bottle (not included in the kit). (Image: Spraying into washing bottle)

Needle & Nozzle Cleaning

Clean the needle and nozzle if necessary. This method thoroughly cleans the paint passage, nozzle, and needle.

1. Unscrew the handle. (Image: Handle unscrewed)
2. Loosen the needle and chucking nut. (Image: Needle and nut loosened)
3. Pull out the needle. (Image: Needle removed)
4. Fold a soft cloth dampened with cleaner over the needle and wipe off residual paint. (Image: Needle wiped with cloth)
5. Unscrew the airbrush nozzle. (Image: Nozzle unscrewed)
6. Insert the cleaning needle or cleaning brush into the body for cleaning. (Image: Cleaning tool inserted)
7. Insert the reamer to clean paint inside the nozzle. (Image: Reamer cleaning nozzle)

Warnings & Precautions

• The compressor should be placed in dry, clean, and ventilated places.
• Do not let children play with it.
• The compressor's ambient temperature should be within 0-40°C and do not put it in direct sunlight.
• Do not let the compressor work for more than 30 minutes if it is not assembled with the hose and the airbrush.
• Please put the airbrush onto the holder when you don't use it so that the airbrush will not be broken.