Draper Intelliflex I/O Typical Wiring Diagram with Contact Closure Interface
System Overview
This document illustrates the typical wiring configuration for the Draper Intelliflex I/O system, incorporating a contact closure interface. The diagram shows the interconnection of various Intelliflex I/O components, including network device connectors, smart motors, and control interfaces, along with power and network connections.
Diagrammatic Representation
The diagram depicts a central network bus connecting multiple components. Two motors, labeled 'M', are shown connected via motor data cables (7) and motor power cables (8) to Intelliflex I/O Network Device Connecters (NDC1 and NDC3, labeled 1 and 2 respectively). These NDC units manage network communication and power distribution. A Contact Closure Interface (4) is shown connecting to a third-party A/V system, facilitating external control via dry contact signals. The system also includes wall switches (3) for local control. Power (11) and junction boxes (10) are indicated as provided by others.
System Components
| Item | Component |
|---|---|
| 1 | Intelliflex I/O Network Device Connector (NDC3), UL Certified, Plenum Rated, Part # C156.311 |
| 2 | Intelliflex I/O Network Device Connector (NDC1), UL Certified, Plenum Rated, Part # C156.322 |
| 3 | Intelliflex I/O Single Zone / Dual Zone Wall Switch, Part# C112.161 / C112.162 |
| 4 | Intelliflex I/O Contact Closure Interface, Part# C156.273 |
| 5 | Intelliflex I/O Smart Motor, Part# C047.300 or C047.303 |
| 6 | Intelliflex I/O Bus Line - Low Voltage (BY OTHERS) - CAT 5E Cable, straight thru connection with RJ45 termination. Overall wire length not to exceed 4000 ft. |
| 7 | Intelliflex I/O Motor Data Cable - CAT 5E Flat Data Cable, straight thru connection with Low Profile RJ45 termination. 3 ft. Standard Length (see inset for available sizes) |
| 8 | Intelliflex I/O Motor Power Cable 120V, 3-Wire Cable (Hot, Neutral, Ground). 1ft. Length. Complete with Male M12 Disconnect Plug |
| 9 | Extension Cable 120V, 3-Wire Cable (Hot, Neutral, Ground). 5ft. Standard Length (see inset for available sizes). Complete with Female M12 Disconnect Plug |
| 10 | Junction Box - by others |
| 11 | 120V Building Power - by others |
| 12 | Roller Shade |
Motor Data Cable Lengths
| Part Number | Length |
|---|---|
| C107.106 | 6' (1.8 m) |
| C107.107 | 12' (3.7 m) |
| C107.108 | 25' (7.6 m) |
| C107.109 | 50' (15.2 m) |
Motor Extension Cable Lengths
| Part Number | Length |
|---|---|
| C107.089.060UL | 5' (1.5 m) |
| C107.089.132UL | 11' (3.4 m) |
| C107.089.204UL | 17' (5.2 m) |
| C107.089.276UL | 23' (7 m) |
RJ45 Connector Pinout (T-568B)
The RJ45 connector for the motor data cable follows the T-568B standard:
- Pin 1: Orange/White
- Pin 2: Orange
- Pin 3: Green/White
- Pin 4: Blue
- Pin 5: Blue/White
- Pin 6: Green
- Pin 7: Brown/White
- Pin 8: Brown
Motor Power Cable Pinout
The 120V motor power cable uses M12 disconnects with the following pinout:
- Pin 1: Black (Hot)
- Pin 2: White (Neutral)
- Pin 4: Green (Ground)
- Pin 3: Not Used
LED Status Indicators
The Network Device Connectors (NDC) feature several LED indicators:
| LED Name | LED Color | LED Display | Description |
|---|---|---|---|
| POWER | GREEN | Solid On | Power to the device |
| NETWORK STATUS | RED | Solid On | Network termination has been set to ON |
| NETWORK STATUS | YELLOW | Blinking | Communicating on the network. The blink pattern shows total number of devices on network. A short blink = 1 device; A long blink = 10 devices |
| DEVICE | BLUE | Always On | Off - No device connected; Solid On - Device connected; Blinking - Device issue |
Notes
A. Wiring layouts are indicative only. It is the responsibility of others to determine the specific requirements and compliance with the local electrical code.
B. All wiring and connections should be completed by licensed electricians, in compliance with Local and State Code.
C. Actual location of control system hardware to be coordinated by others.
Project Notes
- THESE DRAWINGS ARE THE SOLE PROPERTY OF DRAPER INC. AND MAY NOT BE USED OR DUPLICATED WITHOUT WRITTEN CONSENT FROM DRAPER. DRAPER ASSUMES NO RESPONSIBILITY FOR WORK AND/OR ERRORS INCURRED BY OTHER TRADES THROUGH THE USE OF THESE DRAWINGS.
- ALL SHOP DRAWINGS, NOTATIONS, AND DIMENSIONS MUST BE APPROVED BY THE PURCHASER IN ORDER FOR DRAPER TO PROCEED WITH MATERIAL FABRICATION.
Contact Information
Draper, Inc.
411 S. Pearl Street, Spiceland, Indiana 47385
EMAIL: drapercontract@draperinc.com
PH: 765-987-7999
FAX: 866-637-5611
Revision Information
| Revision Description | MM-DD-YY | BY |
|---|---|---|
| SUBMITTED FOR REVIEW | 04-26-23 | BJM |
