ℹ️ Document Conversion Notice:
This document has been converted from PDF and formatted to fit this screen. Diagrams and images may be available only in the original here.
Pro'sKit MT-7063/MT-7064 PoE & LAN Cable Tester User Manual
Thank you for purchasing the Pro'sKit MT-7063/MT-7064 PoE & LAN cable tester. This product is ideal for testing live Ethernet cables and determining continuity of network and telephone cables.
Safety Instructions
⚠ Please read and learn the safety instructions before using or maintaining the equipment:
This cable tester cannot test any electrified product.
Please change the batteries if weak lights appear.
Verify the RJ45 connector and cable are good and properly inserted into the jack. If not properly installed, the LED tester may not work.
Use quality tools to crimp the cables.
Remove the battery if the tester will not be used for a long time.
Features
PoE Tester
Easily tests Ethernet networks for Power over Ethernet existence.
Quickly identifies the type of Power Sourcing Equipment (either End-span or Mid-span).
MT-7063 is an economical type only for detecting Mid-span/End-span.
MT-7064 is an advanced type that can easily identify IEEE 802.3af/at PoE standard and Mid-span/End-span.
Cable Tester
Checks RJ11/RJ12/RJ45 pin-to-pin cable maps.
Automatically runs all tests and checks for continuity, opens, shorts, and crossover wire pairs.
Cable mapping up to 300M.
Product Description
The Pro'sKit MT-7063 and MT-7064 PoE & LAN Cable Testers are compact devices designed for network cable testing. The MT-7063 features a power indicator and pin-out LEDs for End-span (1,2,3,6) and Mid-span (4,5,7,8) detection. The MT-7064 includes additional LEDs (D1-D4) for detailed PoE standard identification (802.3af/at). Both models have RJ45, RJ11, and PoE test connectors, a power switch (OFF/SLOW/ON), and a remote unit for comprehensive cable mapping.
Connect one end of the cable into the PoE connector on the left side of the instrument.
NOTE: This instrument can be tested without turning on the Tester power switch.
When indicator light LED "End-span" is on, it means power is provided by End-span (12/36).
When indicator light LED "Mid-span" is on, it means power is provided by Mid-span (45/78).
When both lights are on at the same time, it means power is provided by Mid-span & End-span (4 pair).
Mid-span
End-span
Result
✓
X
Mid-span (45/78)
X
✓
End-span (12/36)
✓
✓
4 pairs (1236 & 4578)
PoE Test Operation (MT-7064)
Connect one end of the cable into the PoE connector on the left side of the instrument.
NOTE: This instrument can be tested without turning on the Tester power switch.
Test result 1:
When LED "D1" light is on, it means power is provided by End-span (12/36), and it is 802.3af standard, with an output power of 15.4W (PD Max 12.95W).
Test result 2:
When LED "D1" and "D2" lights are on at the same time, it means power is provided by End-span (12/36), and it is 802.3at standard, with an output power of 30W (PD Max 25.5W).
Test result 3:
When LED "D3" light is on, it means power is provided by Mid-span (45/78), and it is 802.3af standard, with an output power of 15.4W (PD Max 12.95W).
Test result 4:
When LED "D3" and "D4" lights are on at the same time, it means power is provided by Mid-span (45/78), and it is 802.3at standard, with an output power of 30W (PD Max 25.5W).
Test result 5:
When the LED "D1" and "D3" lights are on at the same time, it means power is provided by Mid-span & End-span (4 pairs), and it is 802.3af standard, with an output power of 30W.
Test result 6:
When all 4 LEDs are on, it means power is provided by Mid-span & End-span (4 pairs), and it is 802.3at standard, with an output power of 60W.
D1 LED
D2 LED
D3 LED
D4 LED
Result
✓
X
X
X
12/36 cable power, 802.3af standard
✓
✓
X
X
12/36 cable power, 802.3at standard
X
X
✓
X
45/78 cable power, 802.3af standard
X
X
✓
✓
45/78 cable power, 802.3at standard
✓
X
✓
X
12/36/45/78 cable power, 802.3af standard
✓
✓
✓
✓
12/36/45/78 cable power, 802.3at standard
Cable Tester Functions
It can test corresponding double-twisted cable 1,2,3,4,5,6,7,8 and S. Meanwhile, it can identify good connection, shorts, crossover, or opens.
"OFF" means Power off, "ON" means normal scan, "SLOW" means slow scan.
Operation
Slide the power switch to "ON" (Normal grade) position or "SLOW" (Slow grade) position, and then connect the RJ45/RJ11/RJ12 cable with the Master Tester and Remote Tester. The cable mapping will be automatically processed by pin-to-pin scanning as below:
Pin 1-8 8P/8C
Pin 1-6 6P/6C
Pin 2-5 6P/4C
Pin 3-4 6P/2C
Abnormal Connections Instruction
OPENS
While performing the pin-to-pin scanning, if the pin 3 LED does not light up on both the master unit and remote unit, it means Pin 3 is open circuited.
If there are several pins that are not connected, several lights will not turn on. If less than two pins are connected, none of the lights are on.
CROSSOVER
If pins are crossover, for example NO2 and NO4, the result is displayed as below:
Master Tester: 1-2-3-4-5-6-7-8-S
Remote Tester: 1-4-3-2-5-6-7-8-S
SHORT
If two or more pins are short circuited, the lights will not light up on the remote tester while the master tester shows normal.
Testing patch cables or wall installed cables
Two cables which can match each other (e.g., 110P4-RJ45) will be connected to the tester.
Test by RJ45 cable
Slide the power switch to "ON" or "SLOW", the power will turn on.
UTP cable test: Connect the cable, the tester will pin-to-pin scan sequentially from 1 to 8 circulate test.
STP cable test: Connect the cable, the tester will pin-to-pin scan sequentially from 1 to S circulate test.
If any cable is open, short, or crossover, the result is as shown above. When finished testing, turn off the tester. If finished for a long time, remove the battery for storage.
Test by RJ11/RJ12
Slide the power switch to "ON" or "SLOW", the power will turn on.
RJ11 cable test: Connect the cable, the tester will pin-to-pin scan sequentially from 2 to 5 circulate test.
RJ12 cable test: Connect the cable, the tester will pin-to-pin scan sequentially from 1 to 6 circulate test.
If any cable is open, short, or crossover, the result is as shown above. When finished testing, turn off the tester. If finished for a long time, remove the battery for storage.
Directly Connecting to Network Card or Switch for Testing
⚠ NOTE: This test method can only check network cable continuity; it cannot detect crossovers or shorts.
Connect the main tester to an RJ45 (8P/8C) network cable or jack, and the other end to a computer network card or network switch. When the "1-8, S" test result indicator lights on the main tester illuminate sequentially, it indicates that network lines 1-8, S are all connected. If any lights do not illuminate, it indicates a line fault.
Warranty Information
Prokit's Industries Co., Ltd. provides a 12-month free repair warranty from the original purchase date under normal use (excluding consumables). The product warranty card must be stamped with the store seal and date to be effective. Please keep the card properly for repair services.
After the warranty period, adjustment, maintenance, or repair services will incur labor costs. If parts need replacement, additional parts fees will apply.
Product Warranty Description
Within the warranty period, the repair center may charge for material costs or repair fees (as determined by Prokit's Industries Co., Ltd.) for the following situations:
Damage to the product surface, including cracks or scratches on the casing.
Damage caused by misuse, negligence, improper installation or measurement, unauthorized opening or repair of the product, modification of the product, or any other damage beyond the intended scope of use.
Damage caused by accidents, fire, power fluctuations, other hazards, or natural disasters.
Non-Warranty Service Content
Consumables within the main unit: such as batteries, etc.
Accessories outside the main unit: such as test leads, temperature probes, etc.
For repairs or services beyond the warranty period, even if no parts are replaced, the company's warranty and maintenance policy will apply, and service fees will be charged accordingly.
Manufacturer: Prokit's Industries Co., Ltd.
Taiwan Address: 5F, No. 7, Lane 130, Minquan Rd., Xindian Dist., New Taipei City, Taiwan
PRO'SKIT MT-7064 (01) Microsoft Word 2010 Microsoft Word 2010
Related Documents
Pro'sKit MT-7063/MT-7064 PoE and LAN Cable Tester User Manual Comprehensive user manual for Pro'sKit MT-7063 and MT-7064 PoE and LAN cable testers, detailing features, specifications, safety instructions, and operation for testing Ethernet and network cables.
Pro'sKit MT-7051N Multi-Network Cable Tester User Manual User manual for the Pro'sKit MT-7051N Multi-Network Cable Tester, detailing its features, usage, and warranty information. This tester is designed for network testing and can automatically check for continuity, shorts, opens, and crossed wire pairs in various cable types.
Pro'sKit MT-1820N 3 5/6 True-RMS Auto Range Digital Multimeter User Manual User manual for the Pro'sKit MT-1820N, a 3 5/6 digit True-RMS auto-range digital multimeter. Details features, specifications, operation, and safety for this versatile electrical testing tool from Prokit's Industries Co., Ltd.
