Safety Information
IMPORTANT SAFEGUARDS:
ALWAYS FOLLOW BASIC SAFETY PRECAUTIONS WHEN USING ELECTRICAL PRODUCTS, ESPECIALLY WHEN CHILDREN ARE PRESENT.
CAUTION: Requires a transformer (not included): 12-24VAC 60Hz. This product is not user-serviceable. Do not attempt to open the product enclosure for any reason. Before installing your smart video doorbell, thoroughly review enclosed installation guide. If you do not have sufficient electrical wiring experience, please refer to a do-it-yourself wiring handbook or have your smart video doorbell installed by a certified electrician. Reliable operating temperature is -4°F to 122°F (-20°C to 50°C). This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and hazards involved. Min. 90°C supply conductors.
CAUTION: If you are unfamiliar or inexperienced with your home's electrical systems, contact a certified electrician for assistance.
WARNING: This product may represent a possible shock or fire hazard if improperly installed or attached in any way. Product should be installed in accordance with the owner's manual, current electrical codes and/or the current National Electric Code (NEC).
RISK OF ELECTRIC SHOCK: Turn off the main power at the circuit breaker before installing.
Supplier's Declaration of Conformity: 47 CFR § 2.1077 Compliance Information
Responsible Party: Feit Electric Company
4901 Gregg Road
Pico Rivera, CA 90660, USA
www.feit.com
Unique Identifier: CAM/DOOR/WIFI/G2
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. The device can be used in mobile (min 7.87 in.) exposure condition without restriction.
Limited Warranty
This product is warrantied to be free from defects in workmanship and materials for up to 1 year from date of purchase. If the product fails within the warranty period, please visit feit.com/help for instructions on replacement/refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
Pre-Assembly
TOOLS REQUIRED TO MOUNT THE DOORBELL
- Phillips Screwdriver
- Pencil
- Power Drill
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
| Part | Description | Quantity |
|---|---|---|
| AA | Smart Video Doorbell | 1 |
| BB | Standard Mounting Plate | 1 |
| CC | Angled Mounting Plate | 1 |
| DD | USB-A Chime | 1 |
| EE | USB-C Cable | 1 |
| FF | Phillips Screw | 2 |
| GG | Bracket Screws | 2 |
| HH | Mounting Anchors | 2 |
| II | Reset Pin | 1 |
| JJ | Wire Extenders | 2 |
| KK | USB Power Adapter | 1 |
| LL | Locking Screw for The Camera | 2 |
| MM | Port cover | 1 |
| NN | Star-shaped Screwdriver | 1 |
Description
Doorbell Components:
- Lens: The primary camera lens.
- Doorbell Button: The button to activate the doorbell.
- Speaker: For audio output.
- USB-C Port: For power and data connection.
- External Power Port: Connects to the doorbell wires for power (12-24VAC 10VA transformer required, not included). For two doorbells ringing the same mechanical chime box, a 20 or 30 VA transformer is needed.
- Reset Button: Located on the bottom, used for resetting the device.
- MicroSD Card Slot: For storing recordings (supports up to 128GB, FAT32 format, card not included).
Status Light Meanings:
- Blinking RED = Pairing Mode
- Solid RED = Rebooting
- Blinking BLUE = Connecting to Wi-Fi
- Solid BLUE = Connected to Wi-Fi
SD Card Functionality:
Add 128GB or less MicroSD card (not included) to enable recording. Only supports MicroSD card with FAT32 format. Stores up to 10 days of continuous recording based on a 128GB MicroSD card (results may vary).
Reset Function: Press and hold for 5 seconds with the Reset Pin (II) to reset the doorbell.
Mounting & Installation
Shut Off the Power
Shut off the power to your doorbell at the circuit or fuse breaker before installing. [Circuit breaker OFF symbol]
Mark Screw Positions
Mark screw positions using the Mounting Plate (BB) on your wall. [Diagram showing mounting plate on wall with screw marks]
Installing the Mounting Plate
Drill holes at the marked points if installing on a hard surface such as concrete or brick. Insert Mounting Anchors (HH) into holes. You can skip this step if installing on wood or siding. [Diagram showing drilling and inserting anchors]. Use the Mounting Screws (FF) to attach the Mounting Plate (BB) to the wall. [Diagram showing screws attaching plate to wall]. NOTE: Feed your doorbell wires through the center hole before mounting.
Installing the Smart Video Doorbell
Attach your doorbell wires to the External power port on the back of your smart video doorbell (AA). Use the provided wire extenders (JJ) if your existing doorbell wires are too short. Attach the smart video doorbell (AA) onto the Mounting plate (BB). Secure it with a star-shaped screw (LL) using the star-shaped screwdriver (NN). [Diagram showing doorbell attachment].
Optional Angled Wall Mount: Use the Mounting Screws (FF) to attach the Angle Wall Mount (CC) to the wall, then attach the Mounting Plate (BB) to the Angled Mounting Plate (CC). Use the Bracket Screws (GG) to screw in the Mounting Plate (BB). [Diagrams showing angled mount installation]. NOTE: Your existing doorbell wires can go to any terminal on the External Power Port. NOTE: Feed your doorbell wires through the center hole before mounting.
APP Setup
Download and install the Feit Electric app
- Search for the Feit Electric app in the App Store or Google Play Store.
- Download and install the Feit Electric app on your smart device.
Links: App Store | Google Play
Turn on Bluetooth and start the Feit Electric App
- Check to be sure the doorbell is in pairing mode. The RED status light must be blinking rapidly to connect. If the light is not blinking, press and hold the Reset Button until you hear an audible tone. Use the Feit Electric app to complete the set up.
- Tap "Add" in 'Discovering devices...' You will eventually be prompted to enter your Wi-Fi network and password.
- Follow the directions in the Feit Electric app to complete setup.
- You can find more pairing methods in the drop down menu on the device set-up page.
Be sure to connect to a 2.4 GHz Wi-Fi network that covers your installation location.
USB Chime Setup
Supply Power
Supply power to your Wireless Chime (DD) with the USB power adapter near the Smart Doorbell. You can relocate it after pairing the device. [Diagram showing USB chime connected to USB power adapter].
Confirm Status Light
Ensure blue light is on indicating power. [Diagram showing status light on chime].
USB Chime Setup (Continue)
Pair with Smart Doorbell
Press and hold the button near the bottom of the chime for about 5 seconds until you hear a sound. Push the doorbell button on the camera to complete the pairing. [Diagram showing button press on chime and doorbell button press].
Complete Setup
Press the doorbell button to ensure it rings. NOTE: Tapping the Ring Tone Selection button on the chime will play the tone once you have stopped cycling.
USB Chime Functions
- Press to confirm sound.
- Press to cycle through different preset volume levels.
- Press to cycle through different music tones.
NOTE: If you notice chime delays or the chime becomes inactive, you may press (1) the confirm button.
Need Help?
Thank you for your purchase. Questions, comments or feedback? We'd love to hear from you. Visit feit.com/help for support or connect with us:
- Facebook: @FeitElectric
- Twitter: @FeitElectricInc
- Instagram: feitelectriclighting
