EK-FB ASUS PRIME X299 Monoblock Water Block Installation Manual
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.
Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
Before you start using this product please follow these basic guidelines:
- Please carefully read the manual thoroughly before beginning with the installation process!
- Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard's circuit board (PCB).
- The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.
- The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.
STEP 1: GENERAL INFORMATION
Sample photo of ASUS PRIME X299-DELUXE motherboard
Key components identified: CPU socket, X299 PCH (SB), Mosfets.
Bag Content: Bag content is universal for all water blocks, you may not need all screws.
- Thermal grease: 1pc
- M3 PVC washer: 5pcs
- M2.5 PVC washer: 3pcs
- Washer: 3pcs
- M2.5x5 AX1: 3pcs
- M2.5x7 AX1: 3pcs
Replacement mounting mechanism: (EAN: 3830046992956)
STEP 1: PREPARING YOUR MOTHERBOARD
REMOVING STOCK COOLER: Remove all encircled screws. There are 2 screws on the back of the motherboard that need to be removed in order to remove the factory installed MOSFET heat pipe cooling solution. Please store away the factory backplate as it will be reused.
STEP 2: PREPARING YOUR MOTHERBOARD
- APPLYING THERMAL COMPOUND: Apply thermal compound on CPU heat spreader (IHS) - see sample photo on right with enclosed EK-TIM Ectotherm thermal grease. The quantity of about two rice grains is just about right. There is no need to cover the whole IHS. Applying too much thermal grease will have negative impact on the cooling performance!
- CUTTING THERMAL PADS: Your block comes with thermal pads which needs to be trimmed in order to fit the voltage regulation area (MOSFET) on the motherboard's circuit board. WARNING: DIMENSIONS ON PICTURES BELOW ARE SCALED.
Replacement thermal pads @ EKWB web shop:
Thermal PAD F 1mm - (120x16mm) [EAN: 3830046996732]
1. Thermal pad F-1.0mm (for mosfets):
A diagram shows a 1mm thermal pad with dimensions 120x16mm.
STEP 3: PLACING THERMAL PADS ON MOTHERBOARD
Place thermal pads on PCB as shown on the picture.
PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION!
Place 1mm thermal pads in large strip over marked area and make sure all mosfet chips are covered.
A diagram shows the placement of thermal pads on the motherboard.
STEP 3: PLACING THE BLOCK ON TO MOTHERBOARD
PLACING THE BLOCK ON THE MOTHERBOARD: Place the EK-FB ASUS PRIME X299 Monoblock series water block gently to the motherboard or vice versa (as shown on photo below). Make sure that mounting holes are aligned. Place it on factory installed washers on the motherboard (MOSFET area).
STEP 4: ATTACHING BLOCK ON TO THE MOTHERBOARD
Prior to fastening the screws please make sure the mounting holes on the motherboard's circuit board are aligned with the water block.
- A) Mosfet part: Use two M2.5x7 AX1 screws with original backplate. Tighten the screws evenly. Do not use excessive force when tightening the screws!
- B) CPU part: Use four thumb nuts with screws and washers. Tighten the thumb nuts.
Use the enclosed screws and washers as shown in picture below:
Components shown: M3 thumb nut, M2.5x7 screws, M3 PVC Washer, Factory backplate.
STEP 5: CONNECTING THE D-RGB LED STRIP (optional)
Plug the 4-pin connector from Monoblock RGB LED strip to the motherboard. Please ensure that the arrow indicated on the connector is plugged into the 12v line as indicated on your motherboard. Failure to do so will damage your motherboard or LED strip.
For the EK-FB ASUS PRIME X299 Monoblock series water block to operate properly the G1/4 port nearest to the right edge of the water block MUST BE USED AS THE INLET PORT. EK recommends the use of EK-ACF fittings. When using fittings other than EK-ACF series please use hose clamps or appropriate substitute to secure the tubing to the barb. The use of biocide containing and corrosion inhibiting coolant is always recommended for any liquid cooling system.
IMPORTANT: USE THIS OPENING AS INLET PORT!
REQUIRED TOOLS AND MOUNTING SCREWS: scissors, philips screwdriver, Allen key.
