Concept2 SkiErg Assembly Instructions

Getting Started

This procedure will be easier with a helper. Lay out all parts as shown.

Parts Identification

1a. SkiErg Body: Includes flywheel and Performance Monitor PM5, with handle cords attached to the top bracket.
1b. Top Bracket: The main bracket for the upper arms.
1c. Universal Bracket: One bracket for wall or floor stand mounting.
1d. Upper Arms: Two upper arms.

Assembly Steps (General)

Step 1: Attach Upper Arms

Lay the SkiErg body on the floor with the flywheel and PM5 facing upwards. Attach the two upper arms (1d) to the front side of the SkiErg body using four fasteners. Note: The upper arms are labeled 'L' for left and 'R' for right on the inside.

Step 2: Attach Top Bracket

Attach the top bracket (1b) to the tops of the upper arms (1d) using four fasteners (two per side). The white handle cords should be crossed once as shown in the diagram. Remove the shipping insert on the white handle cords to release them.

Mounting Options

Option A: Wall Mounting

Tools Needed for Wall Mounting:

1/2" (13 mm) wrench
Drill with 1/4" bit (6 mm)
(2) 1/4"-20 fasteners
(4) 5/16" lag screws
(4) 5/16" washers
(2) black spacers

Wall Mounting Procedure (Standard 16" Stud Spacing):

Ensure the SkiErg is securely fastened to a solid wall. The SkiErg comes with pre-drilled holes for standard 16" on-center stud wall construction.

Step 1: Attach Universal Bracket to Wall Studs

Hold the SkiErg up against the wall. Align the two outside holes on the universal bracket (1c) with the wall studs. Mark the location of these holes on the wall. Also, mark the locations for the SkiErg bottom bracket where it will align with the wall (left and right sides).

Step 2: Drill Holes and Secure Bracket

Drill 1/4" diameter holes, 2" deep, at each marked location. Assemble a washer onto a lag screw and screw into each hole until tight. Ensure you are drilling into solid material and the SkiErg is firmly attached. Insufficient attachment may lead to injury.

Step 3: Attach SkiErg to Wall Studs

Place a black spacer (6) behind each mounting hole on the SkiErg bottom bracket. Assemble a washer (5) on a lag screw (4) and screw into each mounting hole until tight.

Note on Non-Standard Stud Spacing: If your wall studs are not spaced at 16 inches, or if you are unsure, consult a building professional. Special mounting plates may be required.

Option B: Free-Standing Setup

The SkiErg can be used with an optional floor stand. The floor stand allows for use on any level surface and includes built-in caster wheels. Some assembly of the floor stand itself is required.

Dimensions for Free-Standing Use: 61 cm x 132 cm x 215.9 cm (24 in x 52 in x 85 in).

Floor Stand Weight: 18 kg (35 lb).

Specifications

SkiErg Weight: 20.8 kg (46 lb)
Required Training Area: 61 cm x 132 cm x 215.9 cm (24 in x 52 in x 85 in)
Part Numbers: PN 2230, PN 1297

	Concept2 SkiErg Assembly and Installation Guide Comprehensive guide for assembling and mounting the Concept2 SkiErg, including wall mounting and floor stand options. Features detailed steps, tool requirements, and safety information.
	Concept2 Model D Rowing Machine Assembly Instructions Step-by-step assembly guide for the Concept2 Model D indoor rowing machine, including product specifications and assembly tips.
	Concept2 RowErg Assembly Instructions Comprehensive assembly instructions for the Concept2 RowErg, including parts list, step-by-step guidance, and device holder usage. Learn how to assemble your Concept2 RowErg efficiently.
	Concept2 RowErg Assembly Instructions Step-by-step assembly instructions for the Concept2 RowErg, including parts list, dimensions, weight capacity, and usage tips for the device holder.
	Concept2 BikeErg Assembly Instructions Step-by-step assembly instructions for the Concept2 BikeErg, including parts list, diagrams, and how to use the device holder. Learn how to assemble your BikeErg efficiently.
	Concept2 SkiErg Product Manual: Usage, Maintenance, and Warranty Comprehensive product manual for the Concept2 SkiErg, covering usage techniques, workout intensity, getting started, maintenance procedures, and warranty information. Learn how to optimize your training and care for your SkiErg.
	Concept2 SkiErg Product Manual: Features, Use, and Maintenance Comprehensive product manual for the Concept2 SkiErg, covering usage techniques, workout intensity, safety guidelines, maintenance, and warranty information for this indoor ski training machine.
	Concept2 RowErg Product Manual: Setup, Technique, and Maintenance Comprehensive guide to the Concept2 RowErg indoor rower, covering setup, proper rowing technique, daily and periodic maintenance, damper settings, and warranty information.