Keurig K-Latte Use & Care Guide

Before You Brew

1. Plug & Place

   Remove packing tape from the brewer and frother. Plug into a grounded outlet. Place the frother base on the side of the brewer. Place a large mug (10oz minimum) on the drip tray.

2. Rinse & Fill

   Remove the water reservoir lid. Lift the reservoir straight up to remove it. Rinse the reservoir with fresh water and fill to the MAX fill line. Replace the reservoir, ensuring the lock tabs engage with the brewer. Replace the lid. Do not use distilled water.

3. Clean the Frother

   Remove the lid and whisk from inside the frother. Wash the interior of the frother, lid, and whisk with warm, soapy water. Dry all parts thoroughly with a soft, non-abrasive cloth, then reassemble. Note: The frother is not dishwasher safe. Do not submerge the frother in water. Use only non-abrasive cleaning materials. Dry the interior of the frother and base with a soft cloth after cleaning.

4. Power On

   Press the power button. The green power light will illuminate. The brewer will automatically begin heating water for approximately 4 minutes. The brewer is ready when the heating sound stops.

5. Cleansing Brew

   Lift and lower the brewer handle without inserting a K-Cup pod. The three brew buttons and SHOT button will blink. Press the 6oz button to start a cleansing brew. Pour the hot water into the sink. This one-time setup process is now complete.

   Note: The brewer may take about a minute to reheat between brew cycles.

Make Your First Latte

1. Fill Frother

   Remove the frother lid. Add chilled milk to the MAX line marked inside the frother. Replace the lid and place the frother on the frother base. Press the power button on the frother. The button will illuminate while heating (approx. 3 minutes). Frothing is complete when the button flashes and turns off. Tip: For frothing assistance, call 1-866-901-BREW (2739). Caution: Frother is not microwave or dishwasher safe. Note: Do not under or overfill the frother. Do not operate before adding milk.

2. Place Mug & Pod

   Place a mug on the drip tray. Lift the brewer handle and place a K-Cup pod in the K-Cup pod holder. Lower the handle completely to close the lid. Do not remove the foil lid on the K-Cup pod.

3. Brew a Shot

   The three brew buttons and SHOT button will blink. Press the SHOT button. Brewing is complete when the SHOT button is no longer illuminated. Lift the handle and dispose of the used K-Cup pod. Caution: Hot water is present during brewing; do not lift the handle during the process. Note: Brew buttons disable after 60 seconds; lift and lower the handle to re-activate.

4. Create Your Latte

   Remove the frother from the base. Remove the lid and pour the frothed milk over your shot of coffee. Note: Clean the frother immediately after use.

Brew Your First Coffee

1. Place Mug & Pod

   Place a mug on the drip tray plate. If using a travel mug, remove the drip tray and place the mug on the drip tray base. Lift the handle and place a K-Cup pod in the K-Cup pod holder. Lower the handle completely to close the lid. Do not remove the foil lid on the K-Cup pod. For high altitude brewing, push down slowly on the K-Cup pod in the holder until the bottom is punctured by the exit needle.

2. Brew & Enjoy!

   Select your brew size. The button will remain illuminated while brewing (approx. 1 minute). Brewing is complete when the button is no longer illuminated. Lift the handle and dispose of the used K-Cup pod. The brewer will be ready for another cup in about a minute. Note: Brew buttons disable after 60 seconds; lift and lower the handle to re-activate. Caution: Hot water is present during brewing; do not lift the handle during the process.

Brewer Features

• Frother: Froths milk to create your favorite latte.
• SHOT button: Brews a shot of coffee for delicious, creamy lattes.
• Auto Off: Automatically turns the brewer off 2 hours after the last brew for energy savings.
• Smart Start: Heats and brews in one simple process. Power on, place mug, insert K-Cup pod, lower handle, select brew size. The brewer will heat and then begin brewing automatically.

Caring For Your Brewer

Regular cleaning keeps your brewer running smoothly. Always turn off and unplug your brewer before cleaning.

Frother

Clean immediately after each use and before first use.

1. Remove frother from base, remove silicone ring from lid, and remove whisk.
2. Wash silicone ring, lid, and whisk with warm, soapy water.
3. Clean frother interior with soap and rinse with warm water using a soft, non-abrasive cloth or sponge.
4. Wipe exterior with a soft, damp cloth.
5. Dry all parts thoroughly and reassemble.

Note: Frother is not dishwasher safe. Do not submerge. Use only non-abrasive cleaning materials.

Brewer Exterior

Clean the exterior with a damp, soapy, lint-free, non-abrasive cloth. Never immerse the brewer in water.

Water Reservoir & Reservoir Lid

Clean periodically. Clean in dishwasher (top rack only) or hand wash with a damp, soapy, non-abrasive cloth. Rinse thoroughly. Fill reservoir with clean water and return to brewer. Do not dry the inside with a cloth. Note: Remove water filter before cleaning.

Drip Tray

The drip tray holds up to 8 ounces of overflow. Empty and clean occasionally. Slide it out level to avoid spilling. Clean in dishwasher (top rack only) or with a damp, soapy, lint-free, non-abrasive cloth.

Caring For Your Brewer (Continued)

K-Cup® Pod Holder

To remove, lift handle, grasp top of holder, and push up from underneath until it releases. Align with opening and snap into place. Caution: Sharp needles are present; do not put fingers in the holder. Note: Always remove and dispose of used K-Cup pod after brewing.

Funnel

Wash regularly for a fresh beverage experience. Remove by pulling until it pops off. Replace by orienting snaps to the indent and snapping back.

Exit Needle

Remove pod holder assembly and funnel. Locate exit needle at the bottom of the pod holder. Insert a straightened paper clip to loosen coffee grounds.

Entrance Needle

Lift brewer handle. Locate entrance needle on the underside of the lid. Insert a straightened paper clip into both holes to loosen coffee grounds. Lower handle completely and run two water-only brew cycles. Do not insert a K-Cup pod. Tip: Refer to support.keurig.com for video instructions.

Descaling Your Brewer

Descale your brewer every 3-6 months. Calcium deposits or scale can build up and hinder performance. Regular descaling maintains the heating element and internal parts.

Descaling Procedure

You will need: a large ceramic mug, fresh water, Keurig® Descaling Solution, and access to a sink. Allow approximately 45 minutes.

1. STEP 1: Cleansing Rinse

   Turn off the brewer. Pour an entire bottle of Keurig® Descaling Solution into the emptied water reservoir. Fill the empty bottle with water and pour into the reservoir. Turn the brewer back on. Place a large mug on the drip tray and run a rinsing brew using the largest brew size. Do not use a K-Cup pod.

2. STEP 2: Internal Tank Soak

   Repeat the rinsing brew process until the "add water" light illuminates. Do not use a K-Cup pod. Let the brewer stand for at least 30 minutes while still on. After 30 minutes, discard residual solution and rinse thoroughly.

3. STEP 3: Fresh Water Rinse

   Fill the water reservoir with fresh water to the MAX fill line. Place a large mug on the drip tray and run a rinsing brew using the largest brew size. Do not use a K-Cup pod. Pour contents into the sink. Repeat brew process until you have completed at least 12 rinsing brews using the largest brew size. You may need to refill the water reservoir.

   Note: Foam dispensed from the brewer during cleaning is natural. If the brewer does not fill properly after adding descaler, turn off/unplug, discard solution, rinse reservoir, refill with water, plug in, power on, and repeat Step 3. If problems persist, let the brewer sit unplugged for 30 minutes before continuing the rinse.

Troubleshooting

Frother

• If milk isn't frothing, call Customer Service.
• If brewing coffee and using frother simultaneously, wait 30 seconds after brewing finishes before using the frother. If the light won't illuminate, press the frother button again. If still not working, contact Customer Service.

Grounds in Your Coffee

• Grounds may be in exit or entrance needles. Clean with a straightened paper clip. Refer to Exit Needle and Entrance Needle care instructions.

Brewer Will Not Brew

• Ensure K-Cup pod is securely placed and handle is down. Brew buttons should be flashing.
• If "add water" light is on, fill reservoir to MAX line and ensure it's seated properly. If light persists, contact Customer Service.
• If all brew buttons (small, medium, large, SHOT) are on simultaneously, lift handle, remove K-Cup pod, close handle, place large mug, and press power button once. Brewer may dispense hot water.
• If all brew buttons blink simultaneously, contact Customer Service.
• If frother is in use, wait 30 seconds after frothing finishes before attempting to brew coffee. If still unable to brew, contact Customer Service.

Brewing a Partial Cup

• Exit needle may be clogged. Refer to Exit Needle care instructions.
• Water reservoir may have been removed during brewing. Replace reservoir and perform a rinsing brew without a K-Cup pod.
• Brewer may need descaling. If descaling twice doesn't resolve the issue, contact Customer Service.

Brewer Does Not Have Power or Shuts Off

• Ensure power button is on.
• Plug brewer into its own grounded outlet. Avoid overloaded circuits.
• Brewer automatically turns off 2 hours after last brew for energy savings. Press power button to restart.
• If brewer still has no power, contact Customer Service.

Helpful Hints

For undesirable beverage taste (chlorine, mineral), use bottled or filtered water. Do not use distilled water. Consider a Keurig® Water Filter.

Service

This brewer is not user serviceable. Refer to the Warranty section for service.

Storage

Empty water reservoir before storing or transporting. Store upright in a safe, frost-free environment to avoid water leakage and damage. If stored in a cold environment, warm to room temperature for at least 2 hours before use. Clean reservoir with soap and water and descale after storage.

Click or Call!

Have Questions? Visit support.keurig.com for videos on cleaning, descaling, and more.

Still Need Help? Call 1-866-901-BREW (2739).

Warranty

LIMITED ONE YEAR WARRANTY

Keurig warrants your brewer against defects in materials or workmanship for one year from purchase date under normal home use. Register your brewer at keurig.com/new. Keurig will, at its option, repair or replace a defective brewer free of charge upon receipt of proof of purchase. Replacement brewers may be new or reconditioned and will carry a new one-year warranty. This warranty applies only to brewers operated in the United States and Canada. It grants specific legal rights that may vary by state or province.

Only Keurig® K-Cup® brand pods and accessories guarantee proper function and lifetime. Damage or malfunction from non-Keurig® products may not be covered or may incur a service fee.

Note: Frother is not dishwasher safe. Damage to frother from cleaning is not covered.

WHAT IS NOT COVERED BY THE LIMITED WARRANTY?

This warranty does not cover consequential or incidental damages (e.g., property damage) or incidental costs and expenses resulting from warranty breach. Some states/provinces may not allow these limitations.

Also not covered: damages from non-Keurig® pods/accessories, unauthorized service, non-genuine Keurig® parts, abuse, misuse, inappropriate power supply, or acts of God.

OTHER LIMITATIONS

This warranty is exclusive and replaces all other express warranties. Keurig disclaims all other warranties, including implied warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Some states/provinces may not allow these disclaimers.

HOW DO YOU OBTAIN WARRANTY SERVICE?

Call Keurig Customer Service at 1-866-901-BREW (2739). Do not return your brewer without first obtaining a Return Materials Authorization (RMA) number from Customer Service. Returns without an RMA number will be sent back without servicing.

Parts Diagram

The Keurig K-Latte Single Serve Coffee & Latte Maker consists of the following parts:

• A. K-Cup® Pod Holder (A and B together form the K-Cup® Pod Holder Assembly)
• B. Funnel
• C. K-Cup® Pod Assembly Housing
• D. Power Cord
• E. Drip Tray Plate
• F. Drip Tray
• G. Drip Tray Base
• H. Handle
• I. Water Reservoir Lid
• J. Water Reservoir
• K. Water Reservoir Lock Tab Slots
• L. Frother Lid
• M. Frother Whisk
• N. Frother
• O. Frother Base

For replacement parts, visit www.keurig.com.

Coffeehouse taste in your own home.

FIND YOUR PERFECT POD

With over 70 brands and hundreds of varieties, find your match at keurig.com/new.