Polaroid Dolby Atmos Soundbar

Welcome

Congratulations on purchasing this Sound Bar. This product will improve and amplify the sound from your TV or MP3 player. Please read the warning section on pages 16 & 17 carefully before using your Sound Bar.

What You Should Have

The package should contain the following items:

• Sound Bar
• Power cable
• Wall brackets & fittings
• Wall mounting screws
• 3.5mm audio cable
• Remote control / AAA batteries x2

Need something else? There are a wide range of accessories and other products that can be ordered direct to your door. For more information see www.asda.com.

Your Sound Bar

Description of the Sound Bar unit and its controls:

• 1. Remote control sensor: Receives signals from the remote control.
• 2. Display: Shows the current status of the sound bar.
• 3. Wall bracket screws: Screws used for mounting the sound bar.
• 4. ⏻ button: Use to switch between ON or STANDBY mode.
• 5. ▶ button: Use to select the input source for the Sound Bar.
• 6. ➖ / ➕ buttons: Use to decrease or increase the volume.
• 7. AC~ socket: Connection for the power cable.
• 8. COAXIAL socket: Use to connect the sound bar to a COAXIAL OUT socket on an external device.
• 9. OPTICAL socket: Use to connect the sound bar to an OPTICAL OUT socket on an external device.
• 10. USB socket: Insert a USB device to play music. It can also be used to update the sound bar's software functions.
• 11. AUX socket: Use to connect to the AUX OUT/Headphone sockets on an external device.
• 12. HDMI OUT (TV eARC/ARC) socket: Supports the eARC/ARC HDMI feature, allowing the sound bar to play audio originating from the connected TV.
• 13. HDMI IN 1 / 2 sockets: Two HDMI IN ports for connecting source devices like DVD players, Blu-ray Disc players, or gaming consoles. Note that only one HDMI input is usable at a time.

Preparing the Remote Control

IMPORTANT:

The remote control operates within a 6m range. Obstacles between the unit and the control may affect performance. Using the remote near devices generating infrared rays might cause interference.

Fitting/Replacing the Batteries

To insert or replace batteries:

1. Push down gently on the top of the battery cover and slide it down off the bottom of the remote control.
2. Insert two AAA batteries into the battery compartment, ensuring the '+' and '-' ends are correctly aligned with the marks inside the compartment.
3. Slide the battery compartment cover back onto the bottom of the remote control and push upwards until it locks in place.

Important Battery Information

• If the remote control is not used for over a month, remove the batteries to prevent leakage.
• If batteries leak, clean the compartment and replace with new batteries.
• Only use the specified battery type.
• Do not heat, disassemble, or throw batteries into fire or water.
• Avoid storing batteries with metallic objects, as this can cause short circuits, leaks, or explosions.
• Never recharge a battery unless it is specifically designed for recharging.

Recognising the Remote Control Buttons

The remote control has the following buttons:

1. ⏻: Switches the Sound Bar ON or into STANDBY mode.
2. SOURCE buttons: Selects the input source for the sound bar.
3. Track Navigation: ⏮ Skip to previous track. ⏭ Skip to next track.
4. Playback Control: ▶ Play / pause / resume playback in Bluetooth mode. Press and hold to activate Bluetooth pairing or disconnect a paired device.
5. BASS ➖ / ➕: Adjusts the bass level.
6. ? (Mute): Mutes the sound bar. Press again or use volume buttons to unmute.
7. Volume ➖ / ➕: Decreases or increases the volume.
8. TREBLE ➖ / ➕: Adjusts the treble level.
9. VERTICAL/SURROUND: Turns surround sound ON or OFF.
10. Equaliser Setting Buttons: ? (Voice), ⚽ (Sport), ? (Movie), ? (Music) - Selects the best preset equaliser setting for the material being listened to.
11. DIMMER: Adjusts the brightness of the display.

Positioning Your Sound Bar

The correct position of the Sound Bar:

• Placed on a stand: If your TV is on a stand, place the Sound Bar directly in front of the TV, centered on the middle of the screen.
• Wall mounted: If your TV is wall-mounted, mount the Sound Bar directly below the TV, centered on the middle of the screen.

How to Mount Your Sound Bar on a Wall

IMPORTANT:

Before installing your Sound Bar, please read the following information:

• All installation must be carried out by a qualified person only. Incorrect assembly can result in severe personal injury and property damage. If you intend to install this product yourself, you must check for installations such as electrical wiring and plumbing that may be buried inside the wall. It is the installer's responsibility to verify that the wall will safely support the total load of the Sound Bar and the wall brackets.
• Additional tools (not included) are required for installation.
• Do not overtighten screws.
• Keep this instruction manual for future reference.
• Use an electronic stud finder to check the wall type before drilling and mounting.
• Suggested wall mounting height is ≤1.5 meters.

Fitting the Wall Brackets

WARNING: Before attempting to fit the Sound Bar to the wall, if you are unsure about how or where to fit it, you should employ a qualified person to install your Sound Bar.

IMPORTANT:

The fittings supplied may not be suitable for all types of wall. Consult a professional for advice before drilling any holes if you are in any doubt.

IMPORTANT:

Mark the position on the wall for the Sound Bar and check that it aligns with the holes in the brackets before drilling.

1. Step 1 (Marking): The distance between the outer holes must be 810 mm, with two more holes 30 mm in from them. Ensure the four points are level using a spirit level (?).
2. Step 2 (Drilling): Drill 4 parallel holes (Ø 3-8 mm each, depending on wall type). The distance between the outer holes must be 810 mm, with two more holes 30 mm in from the outer holes. Firmly insert a dowel into each hole (?).
3. Step 3 (Mounting): Slot the screws into the holes in the brackets. Use a crosshead screwdriver (?) through the holes in the front of the bracket to tighten the screws into the wall.

Mounting the Sound Bar

1. Step 1: Remove the two wall bracket screws from the back of the Sound Bar using a crosshead screwdriver (not supplied) (?).
2. Step 2: Screw the two wall mounting screws into the two screw holes left by removing the wall bracket screws (?).
3. Step 3: Align the heads of the wall mounting screws on the back of the Sound Bar with the slots in the tops of the wall brackets (⬆️).
4. Step 4: Gently push the Sound Bar down until it locks in place (⬇️).

Connecting Your Sound Bar

Dolby Atmos®

Dolby Atmos provides an immersive listening experience by developing sound in 3 dimensions, offering richness, clarity, and power. For more information, visit dolby.com/technologies/dolby-atmos.

To use Dolby Atmos®:

Dolby Atmos is only available when your sound bar is connected using the HDMI ARC or HDMI sockets with a HDMI 2.0 cable. While other connection methods (like Digital Optical) will allow the sound bar to function, they may not support all Dolby Atmos features. For the full Dolby Atmos experience, connecting via a HDMI 2.0 cable into the HDMI ARC or HDMI ports is recommended.

Connecting to the HDMI OUT ARC Socket using an HDMI Cable

IMPORTANT:

The ARC (Audio Return Channel) function allows audio from your ARC-compliant TV to be sent to your Sound Bar via a single HDMI connection. For the ARC function to work, ensure your TV is both HDMI-CEC and ARC compliant and configured correctly. When set up properly, you can use your TV remote to adjust the volume or mute the Sound Bar.

1. Connect one end of an HDMI cable (not supplied) into the HDMI OUT ARC socket on the back of the Sound Bar.
2. Connect the other end of the HDMI cable into an HDMI OUT ARC socket on the TV or other device you wish to connect.

TIPS: Your TV must support HDMI-CEC and ARC functions, and both must be set to ON. The specific settings may vary by TV model. Refer to your TV's user manual. HDMI 2.0 or higher version cables are recommended.

Connecting to the HDMI IN Sockets using an HDMI Cable

If your device is not HDMI ARC compatible, you can connect it using the standard HDMI IN ports on the Sound Bar and an HDMI cable. Note: The package does not include an HDMI cable.

1. Use an HDMI cable to connect the soundbar's HDMI OUT (eARC/ARC) socket to the TV's HDMI IN socket.
2. Use an HDMI cable to connect the soundbar's HDMI IN (1 or 2) socket to your external devices (e.g., games consoles, DVD players, Blu-ray players).

TIPS: Only HDMI 2.0 or higher version cables are recommended for this sound bar.

Connecting to the Optical Socket using an OPTICAL Cable

1. Pull the protective cap off the optical socket on the back of the Sound Bar.
2. Connect one end of the OPTICAL cable (not supplied) into the socket on the Sound Bar.
3. Connect the other end of the OPTICAL cable into the OPTICAL socket on your TV or other device.

IMPORTANT:

If there is no sound output and the OPTICAL indicator flashes, ensure the audio setting of the input source (e.g., TV, game console, DVD player) is set to PCM mode with optical input.

Connecting to the COAXIAL Socket using an Audio Coaxial Cable

1. Connect one plug of the audio coaxial cable (not supplied) into the COAXIAL socket on the back of the Sound Bar.
2. Connect the other end of the audio coaxial cable into the COAXIAL OUT socket on your TV or other device.

IMPORTANT:

The Sound Bar may not decode all digital audio formats. If this occurs, the Sound Bar will automatically mute; this is not a fault. Check that the input source (TV, games console, DVD player, etc.) is set to PCM or Dolby Digital (refer to the input device's manual for audio settings) for HDMI / OPTICAL / COAXIAL input. When the DOLBY DIGITAL audio format is detected, the display shows 'DOLBY AUDIO'. When PCM audio is detected, it shows 'PCM AUDIO'. For non-PCM or DOLBY DIGITAL formats, the display will show 'NO SUPPORT' and there will be no sound.

Connecting to the AUX Socket using an RCA to 3.5mm Audio Cable

1. Connect the 3.5mm plug of the RCA to 3.5mm cable (not supplied) into the AUX socket on the Sound Bar.
2. Connect the other end of the cable into the red and white AUX sockets on your TV or other device.

IMPORTANT:

You may need to adjust the audio settings on your TV or connected device. Consult the product's instructions for more information.

Connecting to the AUX Socket using a 3.5mm to 3.5mm Audio Cable

1. Connect one plug of the 3.5mm to 3.5mm audio cable (supplied) into the AUX socket on the back of the Sound Bar.
2. Connect the other end of the cable into the headphone socket on your TV or other device.

Fitting a USB Drive using the USB Socket

1. Connect the USB device into the USB slot on the back of the Sound Bar.

USB Drive Operation

Press the ⏻ button repeatedly on the unit or press the USB button on the remote control to select USB mode.

During Playback:

• To pause or resume play: Press the ▶ button on the remote control.
• To skip to the previous/next file: Press the ⏮ / ⏭ buttons on the remote control.

Note: USB supports MP3 files only, with a maximum memory size of 32GB.

Using Your Sound Bar

Turning On & Off

When first connected to mains power, the Sound Bar enters standby mode. Press the ⏻ button on the Sound Bar or the remote control to turn it ON or OFF. To turn the Sound Bar off completely, unplug it from the mains socket.

Note: If connected to a TV or external device, the Sound Bar will automatically switch on when the source device is turned on. If idle, it will automatically switch to standby mode after approximately 15 minutes.

Mode Selection

Press the ⏻ button on the Sound Bar repeatedly, or press the AUX, BT, OPT/COA, HDMI 1/2, HDMI eARC, or USB buttons on the remote control to select the connection mode corresponding to your external device. The selected mode will be displayed on the Sound Bar's front display.

Adjusting the Bass/Treble Level

Press the BASS ➖ / ➕ or TREBLE ➖ / ➕ buttons on the remote control to adjust the bass or treble levels.

Adjusting the Volume

Press the ➖ / ➕ buttons on the Sound Bar, or the volume ➖ / ➕ buttons on the remote control to increase or decrease the volume.

Muting the Sound

To turn the sound off completely, press the ? button on the remote control. To turn the sound back on, press the ? button again or use the ➖ / ➕ volume buttons.

Turning the Surround Sound ON or OFF

Press the VERTICAL/SURROUND button on the remote control to toggle surround sound ON or OFF.

Setting the Audio Delay (AV SYNC)

Video image processing can sometimes take longer than audio signal processing, causing a delay. The Audio Delay feature corrects this.

IMPORTANT:

You must be connected to the audio source device using a HDMI 2.0 cable via the HDMI eARC socket.

Press and hold the VERTICAL/SURROUND button on the remote control to enter the audio delay setting. The Sound Bar display will show 'LATENCY SET'. Use the volume ➖ / ➕ buttons to adjust the delay in 10-millisecond intervals.

Adjusting the Brightness

Repeatedly press the DIMMER button on the remote control to select your preferred display brightness level.

Using the Equalizer (EQ) Effect

Press the VOICE (?), SPORT (⚽), MOVIE (?), or MUSIC (?) buttons on the remote control to select the desired preset equaliser effect.

AUX, OPTICAL, COAXIAL or HDMI Operation

Ensure your Sound Bar is connected to the TV, DVD player, or audio device as described on pages 10 to 13.

When the Sound Bar is turned on, press the ⏻ button on the Sound Bar or the AUX, OPT/COA, HDMI 1/2, or HDMI eARC buttons on the remote control. The selected mode will be shown on the Sound Bar's display.

Use the connected device's remote control or its own controls to operate playback features.

Tips:

The Sound Bar may not decode all digital audio formats. If this happens, it will automatically mute (this is not a fault). Check that the input source (TV, games console, DVD player, etc.) is set to PCM or Dolby Digital (refer to the input device's user manual for audio setting details) for HDMI 1 / HDMI 2 / HDMI eARC / OPTICAL / COAXIAL input.

When the DOLBY DIGITAL audio format is entered, the Sound Bar display will show 'DOLBY AUDIO'. When the PCM audio format is entered, the Sound Bar display will show 'PCM AUDIO'. When playing non-PCM or DOLBY DIGITAL audio formats, there will be no sound, and the display will show 'NO SUPPORT'.

The full Dolby Atmos experience is only available when the Sound Bar is connected via a HDMI 2.0 cable. The Sound Bar will still function with other connection methods (like Digital Optical Cable), but these may not support all Dolby features. Connecting via HDMI is recommended for full Dolby support.

Using the Bluetooth Function

IMPORTANT:

The operational range between the Sound Bar and a Bluetooth-enabled device is approximately 8 meters. The device you wish to connect must support the Advanced Audio Distribution Profile (A2DP). Before connecting, ensure you know how to use the Bluetooth function of your device.

Obstacles between the Sound Bar and the device can reduce signal strength. Keep both devices away from other electrical devices that might interfere with the Bluetooth signal.

IMPORTANT:

Not all Bluetooth devices are compatible with this Sound Bar.

Pairing the Sound Bar with a Bluetooth-Enabled Device

1. Turn on the Bluetooth function on the device you wish to pair.
2. Press the ⏻ button on the Sound Bar until 'BT' is shown on the display, or press the BT button on the remote control. If the Sound Bar is not paired, 'NO BT' will be displayed.
3. On your device, check the found list for 'PLA21SB001A' and connect to it.
4. If the Bluetooth connection is successful, the Sound Bar will give an audio prompt 'Paired', and the display will show 'BT'.
5. To disconnect the device, switch to another function on the Sound Bar or press and hold the ▶ or BT button on the remote control. The Bluetooth connection will be disconnected when you hear an audible prompt.

Tips on Using the Bluetooth Function

• If requested, enter the password '0000'.
• If no other Bluetooth device pairs with this player within two minutes, the player will revert to its previous connection.
• The device will also disconnect if you move out of the Sound Bar's range.
• To reconnect, move closer to the Sound Bar. Note: Check your device's Bluetooth list to ensure the Sound Bar is still connected.
• If the connection is lost, follow the pairing instructions again.

Listening to Music

If your connected Bluetooth device supports Advanced Audio Distribution Profile (A2DP), you can listen to music stored on the device through the player.

If the device also supports Audio Video Remote Control Profile (AVRCP), you can use the player's remote control to manage music playback.

1. Pair the device with the Sound Bar.
2. Play music via your device (if it supports A2DP).
3. Use the supplied remote control to control playback from the device (if it supports A2DP).

• To pause/resume play: Press the ▶ button on the remote control.
• To skip to a track: Press the ⏮ / ⏭ buttons on the remote control.

Troubleshooting

Warnings

This product was designed and manufactured to meet strict quality and safety standards. Please be aware of the following operational precautions:

• Read these instructions: All safety and operating instructions should be read before operating the product.
• Keep these instructions: Retain the safety and operating instructions for future reference.
• Heed all warnings: Adhere to all warnings on the appliance and in the operating instructions.
• Follow all instructions: Follow all operating and use instructions.
• Do not use near water: Do not use the appliance near water or moisture, such as in wet basements or near swimming pools.
• Clean with a dry cloth: Clean only with a dry cloth.
• Do not block ventilation: Do not block any ventilation openings. Install according to manufacturer's instructions.
• Avoid heat sources: Do not install near heat sources like radiators, heaters, stoves, or other apparatus that produce heat.
• Protect power cord: Protect the power cord from being walked on or pinched, especially at plugs, power boards, and where it exits the Sound Bar.
• Use specified accessories: Only use attachments/accessories specified by the manufacturer.
• Unplug during storms: Unplug the appliance during thunderstorms or when unused for long periods.
• Refer servicing to qualified personnel: Servicing is required if the appliance is damaged (e.g., damaged power cord or plug), if liquid has been spilled or objects fallen into the unit, if exposed to rain or moisture, if it does not operate normally, or if it has been dropped.
• Class II Equipment: This equipment is a Class II or double insulated electrical appliance. It is designed not to require a safety connection to electrical earth.

CAUTION: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Do not expose to dripping or splashing. Do not place liquid-filled objects (e.g., vases) on the apparatus.

The mains plug/appliance coupler serves as the disconnect device and must remain readily operable.

WARNING: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

• The battery(ies) shall not be exposed to excessive heat such as sunshine or fire.
• Before operating, check that the system voltage matches your local power supply voltage.
• Ventilation openings should not be impeded by items like newspapers or curtains.
• Do not place the unit close to strong magnetic fields.
• If a solid object or liquid falls into the system, unplug it and have it checked by qualified personnel before further operation.
• Do not attempt to clean the unit with chemical solvents, as this may damage the finish. Use a clean, dry, or slightly damp cloth.
• When removing the power plug, always pull directly on the plug, never yank the cord.
• No naked flame sources, such as lighted candles, should be placed on the apparatus.
• Changes or modifications not expressly approved by the party responsible for compliance will void the user's authority to operate the equipment.
• The marking label is located on the bottom or back of the equipment.

DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD. The remote control contains a coin/button battery. If swallowed, it can cause severe internal burns in just 2 hours, leading to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you suspect batteries have been swallowed or placed inside the body, seek medical attention immediately.

This appliance is not intended for use by young children or infirm persons without supervision.

IMPORTANT INFORMATION:

If a television is not positioned stably, it can be hazardous due to falling. Many injuries, especially to children, can be avoided by taking simple precautions:

• Use cabinets or stands recommended by the TV manufacturer.
• Use only furniture that can safely support the TV.
• Ensure the TV is not overhanging the edge of the supporting frame.
• Do not place the TV on tall furniture (e.g., cupboards, bookcases) without anchoring both the furniture and TV to a suitable support.
• Do not place the TV on cloth or other materials between the TV and the supporting furniture.
• Educate children about the danger of climbing on furniture to reach the TV or its controls.

This declaration confirms that the product complies with the essential requirements and other relevant provisions of Directive 2014/53/EU.

Battery Disposal Information

The batteries in this product contain chemicals harmful to the environment. To preserve the environment, dispose of used batteries according to local laws and regulations. Do not dispose of batteries with normal household waste. For more information, contact your local authority or the retailer where you purchased the product.

Technical Specifications

Features and specifications are subject to change without prior notice.

Free 1 Year Guarantee

All electrical items are covered by a full 1-year guarantee from the day of purchase. In the unlikely event that your product is faulty or you are struggling to set it up, follow these steps:

1. First, call our Customer Helpline. They may be able to help resolve the problem.
2. If the problem cannot be resolved, you will receive a reference number.
3. Take the reference number, along with the item, all its components, and your receipt, to your nearest store for a full refund.

Customer Services: 0333 600 7700

This does not affect your statutory rights.