MATTRADITION Extractor Hood

General Information

This manual provides essential information for the safe installation, operation, cleaning, and maintenance of your MATTRADITION extractor hood. Please read all instructions carefully before use.

For a full list of IKEA appointed Authorized Service Centres and national phone numbers, please refer to the last page of this manual.

Safety Information

Your safety and the safety of others is paramount. Always observe the safety warnings provided in this manual and on the appliance itself.

Before first use:

• Remove all cardboard protection pieces, protective film, and adhesive labels from accessories.
• Check the appliance for any transport damage.
• Do not place weights on the appliance.
• Do not expose the appliance to atmospheric agents.

Attention Symbol: [!] This symbol indicates potential risks to yourself and others.

DANGER: Indicates a hazardous situation which, if not avoided, will cause serious injury.

WARNING: Indicates a hazardous situation which, if not avoided, could cause serious injury.

All safety warnings provide specific details of potential dangers and how to reduce risks of injury, damage, and electric shock from improper use.

Precautions and General Recommendations

• Electrical installation and connection must be performed by a qualified technician according to manufacturer instructions and local safety regulations. Do not repair or replace parts unless specified in the manual.
• Disconnect the appliance from the power supply before any installation work.
• WARNING: Failure to install screws or fixing devices correctly may result in electrical hazards.
• Earthing of the appliance is compulsory (unless identified as Class II).
• Do not pull the power supply cable to unplug.
• Electrical components must not be accessible to the user after installation.
• Do not touch the appliance with wet body parts or operate when barefoot.
• Children aged 8 and above, and persons with reduced capabilities, can use the appliance with supervision and understanding of hazards. Children shall not play with the appliance. Cleaning and maintenance by children require supervision.
• All other maintenance must be carried out by a specialized technician.
• When drilling walls, be careful not to damage electric connections or pipes.
• Air vents must always discharge to the outside.
• The manufacturer is not responsible for damage caused by improper use or wrong settings.
• Regular maintenance and cleaning ensure good working order and performance. Clean surfaces regularly to avoid grease build-up. Remove, clean, or change filters as per "Cleaning and maintenance" instructions.
• Never flame cook (flambé) under the appliance; free flames can cause fire.
• Failure to follow cleaning and filter replacement instructions may result in fire.
• Exhaust air must not be vented through flues used by gas combustion appliances or other combustible materials; use a separate outlet. Observe national regulations for fume extraction.
• Ensure adequate ventilation if the hood is used simultaneously with gas or other combustible appliances. The room's negative pressure should not exceed 4 Pa (4x10-5 bars). Ensure the room is well ventilated. Consult a qualified person if in doubt.
• Do not leave frying pans unattended while frying, as frying oil may catch fire.
• Ensure light bulbs are cold before touching them.
• Do not use or leave the hood without the light bulb correctly fitted, as this may cause electric shock.
• The hood is not a work surface; do not place objects on it or overload it.
• Wear appropriate working gloves during installation and maintenance.
• This appliance is not suitable for outdoor use.
• WARNING: Accessible parts of the hood may become hot when the hob is in use.

Installation and Connection

In case of problems, contact the Authorized Service Centre. To prevent damage, remove the appliance from its packaging only at the time of installation.

Preparing for Installation

WARNING: This is a heavy product; it should only be lifted and installed by two or more people.

Minimum distance between the hob and the bottom of the hood:

• 65 cm for burning gas or other fuels.
• 60 cm for electric cookers.

Always check the minimum distances stated in the cooker's manual and observe any greater distances specified.

Range hoods can affect the safe operation of gas appliances due to back flow of combustion gases, potentially causing carbon monoxide poisoning. After installation, the operation of flued gas appliances should be tested by a competent person to ensure this does not occur.

Electrical Connection

Ensure the power voltage specified on the appliance rating plate matches the mains voltage.

Information regarding power cable replacement (type H05 VV-F) and electrical plug connection can be found on the inside of the hood, under the grease filter. Power cable replacement must be carried out by a qualified electrician. If the hood has an electric plug, connect it to a socket complying with current regulations and located in an accessible place.

WARNING: If the hood is fitted with direct wiring to the mains (no plug) or if the socket is not accessible, a qualified electrician should install a standardised double pole power switch for complete isolation from the mains, in accordance with wiring rules.

Use

The hood is designed for either "Extraction installation" (venting air outside) or "Recirculation installation" (filtering and returning air to the room).

Extraction Installation

Cooking steam is sucked and channelled outside through a discharge duct (not supplied) fitted to the hood's steam outlet. Ensure the discharge duct is correctly fitted to the air outlet using an appropriate connection system.

Important: If already installed, remove the charcoal filter(s).

Recirculation Installation

The air is filtered through one or more charcoal filters and then returned to the room.

Important: Ensure appropriate air circulation around the hood.

Important: If the hood is supplied without charcoal filters, they must be fitted before use. Filters are available at IKEA shops.

The hood should be installed away from particularly dirty areas, windows, doors, and heat sources.

Wall fixing accessories are not included as different wall materials require different fixing systems. Use systems suitable for your walls and the appliance's weight. Contact a specialized dealer for details.

Keep this booklet for future consultation.

Product Description

The main components of the hood are:

• 1. Chimney
• 2. Control Panel
• 3. Light
• 4. Grease filter

Control Panel

A. Motor ON/OFF toggle switch

B. Suction (power) speed selector knob:

• Low suction (power) speed
• Medium suction (power) speed
• High suction (power) speed
• Maximum suction (power) speed

NB: The hood speed remains the same when switched ON/OFF using the toggle switch.

C. Light ON/OFF toggle switch

Cleaning and Maintenance

WARNING: Never use steam cleaning equipment. Always disconnect the hood from the electric power supply before cleaning.

IMPORTANT: Do not use corrosive or abrasive detergents. If any product accidentally contacts the appliance, clean immediately with a damp cloth.

• Clean surfaces with a damp cloth. If very dirty, add a few drops of washing-up detergent to the water. Finish with a dry cloth.
• IMPORTANT: Do not use abrasive sponges or metallic scrapers/scourers, as they can damage the surface over time.
• Use detergents specifically designed for cleaning the appliance and follow manufacturer instructions.
• IMPORTANT: Clean the grease filters at least monthly to remove oil or grease residuals.

To Clean the Grease Filter

The metal grease filter has an unlimited life and must be washed once a month, either by hand or in a dishwasher at low temperature with a short cycle. Washing in a dishwasher may cause the filter to become dull, but this does not affect its filtering capacity.

Grease Filter Maintenance:

1. Disconnect the hood from the electric power supply.
2. Remove the grease filters: pull the spring release handle downwards, then remove the filter.
3. After cleaning, remount the grease filter in reverse order, ensuring the entire extraction surface is covered.

Charcoal Filter Maintenance (Recirculation Mode)

1. Pull out the plug or disconnect the power supply.
2. Remove the grease filter.
3. If carbon filters are fitted (covering the motor impeller grilles) and need replacement, turn the central handle anti-clockwise to unlock them.
4. Open the two filter shells.
5. Pull out the two circular mats.
6. Proceed in reverse order to fit the new filters.
7. Refit the grease filters.

Unlike traditional charcoal filters, this type can be washed and reactivated. Clean monthly. The best method is a dishwasher wash at the highest temperature possible with normal detergent. Wash the filter alone to avoid unpleasant smells from food particles. After washing, dry the filter in the oven at 100°C for 10 minutes to reactivate it. The filter retains its odour-absorbing capacity for three years, after which it must be replaced.

Lamp Maintenance

The hood is equipped with an LED lighting system. LEDs provide optimum lighting, last up to 10 times longer than traditional lamps, and save 90% electrical energy.

For replacement, contact the Authorized Service Centre.

What to do if... (Troubleshooting)

Before contacting the Authorized Service Centre:

Try switching the appliance on again. If the problem disappears, it was temporary. If not, switch it off and try again after an hour. If the appliance still does not work properly after these checks and troubleshooting steps, contact the Authorized Service Centre. Clearly explain the problem and specify:

• The type of fault.
• The model.
• The type and serial number of the appliance (found on the rating plate).
• The Service number (found after the word SERVICE on the rating plate inside the appliance).

Technical Data

Technical information is located on the rating plate inside the appliance.

Environmental Concerns

Disposal of Packing

Packing material is 100% recyclable and marked with the recycle symbol [recycle]. Dispose of parts responsibly according to local authority regulations.

Scrapping the Product

This appliance is marked in compliance with European Directive 2012/19/EU (WEEE). Proper disposal helps prevent negative environmental and health consequences. The symbol [recycle] on the product or documentation indicates it should not be treated as domestic waste but taken to an appropriate collection centre for electrical and electronic equipment recycling.

Scrapping of Household Appliances

This appliance is made with recyclable or reusable materials. Dispose of it according to local waste disposal regulations. Cut off the power supply cable before scrapping. For more information, contact your local authority, waste collection service, or the store where you purchased the appliance.

Energy Saving Tips

• Switch ON the hood at minimum speed when cooking starts and keep it running for a few minutes after cooking finishes.
• Increase speed only for large amounts of smoke and vapour; use boost speeds only in extreme situations.
• Replace charcoal filters when necessary for good odour reduction efficiency.
• Clean grease filters when necessary for good grease filter efficiency.
• Use the maximum diameter of the ducting system indicated in this manual to optimize efficiency and minimize noise.

Declaration of Conformity

This appliance has been designed, manufactured, and marketed in compliance with:

• Safety objectives of the "Low Voltage" Directive 2014/35/EU.
• Eco design requirements of European regulations n. 65/2014 and n. 66/2014, in conformity to the European standard EN 61591.
• Protection requirements of Directive "EMC" 2014/30/EU.

Electrical safety is guaranteed only if the appliance is correctly connected to an approved earthing system.

IKEA Guarantee

How long is the IKEA guarantee valid?

The guarantee is valid for five years from the original date of purchase from IKEA Pty Ltd or IKEA New Zealand Limited. The original sales receipt is required as proof of purchase. Service work under guarantee does not extend the guarantee period.

Who will execute the service?

IKEA Authorized Service Centres will provide service through their own operations or an Authorized Service Centre network. Contact IKEA for further information. Refer to www.ikea.com for local store after-sales service details.

Contact Details:

Australia: IKEA Authorized Service Centre at www.IKEA.com or IKEA Pty Ltd, IKEA Service Office, L1 Clock Tower, 630 Princes Highway, Tempe, NSW 2044. Phone: (02) 9010 0264.

New Zealand: IKEA Authorized Service Centre at www.IKEA.com or IKEA New Zealand Limited, IKEA Service Office, L1 Clock Tower, 630 Princes Highway, Tempe, NSW 2044. Refer to the contact us section on the website.

What does this guarantee cover?

The guarantee covers faults caused by faulty construction or material faults from the date of purchase. It applies to domestic use only and does not cover damage from commercial use. Costs for repairs (parts, labour, travel) are covered, provided the appliance is accessible without special expenditure. Replaced parts become IKEA property.

The guarantee is valid if the appliance complies with technical specifications, Assembly Instructions, and User Manual Safety Information.

IKEA's guarantee is subject to Australian Consumer Law and New Zealand Consumer Guarantees Act 1993, and is in addition to statutory warranties.

What will IKEA do to correct the problem?

An IKEA appointed service provider will examine the product and decide if it is covered. If covered, they will repair the defective product or replace it with a comparable one.

What is not covered under this guarantee?

• Normal wear and tear.
• Deliberate or negligent damage, or damage caused by failure to observe operating and maintenance instructions, incorrect installation, wrong voltage connection, chemical/electrochemical reactions, rust, abrasion, corrosion, or water damage (including lime scale).
• Damage caused by abnormal environmental conditions.
• Damage from use other than intended.
• Damage from power outages, surges, or incorrect supply voltage.
• Consumable parts (batteries, lamps), removable wire, glass/plastic trays, and other accessories.
• Internal or external damage from excessive use of cleaning products or agents.
• Non-functional or decorative parts (scratches, color differences) that do not affect normal use.
• Accidental damage or blockages caused by foreign objects (coins, nails, jewelry), or from cleaning/unblocking filters, drainage systems, or soap drawers.
• Damage caused by vermin, insects, or pets.
• Internal or external cabinet transport damage (must be reported within 7 days of purchase).
• Damage to specific parts like ceramic glass, accessories, baskets, pipes, seals, lamps/covers, screens, knobs, casings (unless a production fault).
• Cases where no fault is found by a technician.
• Consequential loss due to appliance failure.
• Repairs not carried out by appointed service providers or using non-original parts.
• Repairs due to unauthorized modifications.
• Repairs caused by faulty or non-specified installation.
• Problems caused by incorrect or inadequate venting.
• Use in a non-domestic (professional) environment.
• Transportation damages (if customer transports). IKEA is liable for damage during delivery if IKEA delivers the product.
• Cost for initial installation (though service centres will reinstall if repair/replacement is done).

How country law applies?

Goods come with guarantees that cannot be excluded under the Australian Consumer Law (ACL) and New Zealand Consumer Guarantees Act 1993. You are entitled to a replacement or refund for a major failure and compensation for other reasonably foreseeable loss or damage. Goods will be repaired or replaced if they fail to be of acceptable quality and the failure is not major. This guarantee does not limit or exclude statutory rights.

For more information, visit:

• Australian Consumer Law: www.accc.gov.au
• Commerce Commission NZ: https://comcom.govt.nz/
• Consumer Protection NZ: https://www.consumerprotection.govt.nz/general-help/consumer-laws/consumer-guarantees-act

Area of Validity

The IKEA guarantee applies only to products purchased and installed in AUSTRALIA and New Zealand.

What you must do to make a claim under the guarantee

Contact IKEA Authorized Service Centre at the address provided or refer to www.ikea.com for local store customer service details. Describe the problem in detail, along with your product article number (8-digit code) and date of purchase.

Contact the dedicated Authorized Service Centre for IKEA appliances to:

1. Make a service request under this guarantee.
2. Ask for clarification on installation of the IKEA appliance in IKEA kitchen furniture.
3. Ask for clarification on user manual contents and specifications.

Please read the Assembly Instructions and/or User Manual section carefully before contacting us for assistance.

How to reach if you need our service

The IKEA Authorized Service Centre will assist with basic troubleshooting by phone during warranty call registration. Refer to www.ikea.com or the phone numbers below and select your local store.

Australia: (02) 9010 0264

New Zealand: Refer to contact us section on the website.

Please describe the problem in detail, along with your product model number, serial number, and date of purchase. Always refer to the IKEA article number (8-digit code) and 12-digit service number on the appliance's rating plate.

SAVE THE SALES RECEIPT! Keep all details and the original invoice handy for the service technician. It is your proof of purchase required for the guarantee to apply.