Installation Manual-MEAN WELL Switching Power Supply ManufacturerProduct Liability Disclaimer-MEAN WELL Switching Power Supply Manufacturer
Owner's Manual for MEAN WELL models including: ELG-200-C700, ELG-200-C1050, ELG-200-C1400, ELG-200-C1750, ELG-200-C2100, ELG-200-C Series Constant Current Mode LED Driver, Constant Current Mode LED Driver, Current Mode LED Driver, Mode LED Driver, LED Driver
MEAN-WELL USA, INC. - РКС Компоненти - РАДІОМАГ
File Info : application/pdf, 11 Pages, 776.48KB
DocumentDocument150~200W Constant Current Mode LED Driver
ELG-200-C series
User's Manual
IP65 IP67
IS 15885(Part 2/Sec13)
THOMAS SAMUEL
THOMAS SAMUEL
R-41027766
(for 700A only)
8
{
A
Dx
Downloaded from Arrow.com.
File Name:ELG-200-C-SPEC 2022-02-11
150~200W Constant Current Mode LED Driver
ELG-200-C series
SPECIFICATION
MODEL
ELG-200-C700
ELG-200-C1050
ELG-200-C1400
ELG-200-C1750
ELG-200-C2100
OUTPUT
RATED CURRENT
700mA
1050mA
1400mA
200VAC ~ 305VAC
RATED POWER
200.2W 100VAC ~ 180VAC
199.5W
198.8W
150.5W
150.15W
149.8W
CONSTANT CURRENT REGION Note.2 142 ~ 286V
95 ~ 190V
71 ~ 142V
OPEN CIRCUIT VOLTAGE(max.) 300V
200V
160V
Adjustable for A/AB-Type only (via built-in potentiometer)
CURRENT ADJ. RANGE 350 ~ 700mA
525 ~ 1050mA
700 ~ 1400mA
CURRENT RIPPLE
5.0% max. @rated current
CURRENT TOLERANCE ±5.0%
SET UP TIME Note.4
800ms/115VAC, 500ms/230VAC
1750mA
199.5W
150.5W 57 ~ 114V 120V
875 ~ 1750mA
2100mA
201.6W
151.2W 48 ~ 96V 105V
1050 ~ 2100mA
VOLTAGE RANGE Note.3 FREQUENCY RANGE POWER FACTOR (Typ.)
100 ~ 305VAC 142 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section)
47 ~ 63Hz
PF0.97/115VAC, PF0.95/230VAC, PF0.92/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
INPUT
TOTAL HARMONIC DISTORTION
THD< 20%(@load50%/115VC,230VAC; @load75%/277VAC) (Please refer to "TOTAL HARMONIC DISTORTION(THD)" section)
EFFICIENCY (Typ.)
93%
93%
92%
92%
92%
AC CURRENT (Typ.) INRUSH CURRENT(Typ.)
1.8A / 115VAC 1.0A / 230VAC 1.0A/277VAC COLD START 65A(twidth=680s measured at 50% Ipeak)/230VAC; Per NEMA 410
MAX. No. of PSUs on 16A CIRCUIT BREAKER
2 units (circuit breaker of type B) / 4 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
<0.75mA / 277VAC
NO LOAD / STANDBY
No load power consumption <0.5W for Blank / A / Dx / D2-Type
POWER CONSUMPTION Standby power consumption <0.5W for B / AB / DA-Type
SHORT CIRCUIT PROTECTION OVER VOLTAGE
Hiccup mode, recovers automatically after fault condition is removed
315 ~ 370V
205 ~ 250V
160 ~ 180V
125 ~ 150V
Shut down o/p voltage, re-power on to recover
105 ~ 130V
OVER TEMPERATURE WORKING TEMP.
Shut down o/p voltage, re-power on to recover Tcase=-40 ~ +85 (Please refer to " OUTPUT LOAD vs TEMPERATURE" section)
MAX. CASE TEMP.
Tcase=+85
WORKING HUMIDITY
20 ~ 95% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80, 10 ~ 95% RH
TEMP. COEFFICIENT
±0.03%/ (0 ~ 60)
VIBRATION
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY STANDARDS
UL8750(type"HL"), CSA C22.2 No. 250.13-12;BS EN/EN/AS/NZS 61347-1,BS EN/EN/AS/NZS 61347-2-13 independent, BS EN/EN62384;GB19510.14,GB19510.1;EAC TP TC 004;BISIS15885(for 700A only); IP65 or IP67;KC61347-1,KC61347-2-13 approved
DALI STANDARDS
SAFETY & WITHSTAND VOLTAGE
EMC
ISOLATION RESISTANCE
EMC EMISSION
EMC IMMUNITY MTBF
Compliance to IEC62386-101,102,(207 by request) for DA Type only
I/P-O/P:3.75KVAC I/P-FG:2.0KVAC O/P-FG:1.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH Compliance to BS EN/EN55015,BS EN/EN61000-3-2 Class C (@load50%) ; BS EN/EN61000-3-3; GB17625.1, GB17743;EAC TP TC 020; KC KN15,KN61547 Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level(surge immunity:Line-Earth:6KV, Line-Line:4KV);EAC TP TC 020; KC KN15,KN61547
958.9K hrs min. Telcordia SR-332 (Bellcore) 235Khrs min. MIL-HDBK-217F (25)
OTHERS DIMENSION PACKING
244*71*37.5 mm (L*W*H) 1.22Kg; 12pcs /15.2kg / 0.72CUFT
NOTE
Product Liability DisclaimerFor detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
Downloaded from Arrow.com.
File Name:ELG-200-C-SPEC 2022-02-11
150~200W Constant Current Mode LED Driver
ELG-200-C series
BLOCK DIAGRAM
EMI FILTER
I/P
&
RECTIFIERS
PFC CIRCUIT
POWER SWITCHING
O.T.P. PFC CONTROL
O.L.P.
PWM & PFC CONTROL
CASE :Protective Earth
RECTIFIERS &
FILTER
PFC fosc : 50~120KHz PWM fosc : 60~130KHz
O.L.P.
DETECTION CIRCUIT
O.V.P.
Vo+ VoDIM+ DIM(B Type)
DRIVING METHODS OF LED MODULE
This series works in constant current mode to directly drive the LEDs.
Vo(%)
100
50 (min.)
Constant Current area
In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL.
Hiccup Protection
50
100
Io(%)
Typical output current normalized by rated current (%)
Downloaded from Arrow.com.
File Name:ELG-200-C-SPEC 2022-02-11
150~200W Constant Current Mode LED Driver
ELG-200-C series
DIMMING OPERATION
3 in 1 dimming function (for B/AB-Type)
AC/N(Blue) AC/L(Brown)
ELG-200-C
DIM+(Purple)* DIM-(Pink)** Vo-(Blue) Vo+(Brown)
Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal or resistance.
Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100A (typ.)
* DIM+ for B/AB-Type DA+ for DA-Type PROG+ for D2-Type
* *DIM- for B/AB-Type DA- for DA-Type PROG- for D2-Type
Applying additive 0 ~ 10VDC
Vo+ +
+
Vo-
-
DIM+ +
Additive Voltage
DIM-
"DO NOT connect "DIM- to Vo-"
Output current (%)
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
0% 0V 1V
2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage
Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
Vo+ +
+
Vo-
-
DIM+
Additive PWM signal DIM-
"DO NOT connect "DIM- to Vo-"
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0%
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input
Applying additive resistance:
100%
Output current (%)
Vo+ +
VoDIM+
90%
+
80%
70%
-
60%
50%
40%
Additive Resistance
30%
DIM-
20%
"DO NOT connect "DIM- to Vo-"
10%
0%
Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N
(N=driver quantity forsynchronized dimmingoperation)
Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%.
Dimming input: Additive resistance
2. The output current could drop down to 0% when dimming input is about 0k or 0Vdc, or 10V PWM signal with 0% duty cycle.
Downloaded from Arrow.com.
File Name:ELG-200-C-SPEC 2022-02-11
150~200W Constant Current Mode LED Driver
ELG-200-C series
DALI Interface (primary side; for DA-Type) Apply DALI signal between DA+ and DA-. DALI protocol comprises 16 groups and 64 addresses. First step is fixed at 8% of output.
Smart timer dimming function (for Dxx-Type by User definition) MEAN WELL Smart timer dimming primarily provides the adaptive proportion dimming profile for the output constant current level to perform up to 14 consecutive hours. 3 dimming profiles hereunder are defined accounting for the most frequently seen applications. If other options may be needed, please contact MEAN WELL for details.
Ex : D01-Type: the profile recommended for residential lighting
Set up for D01-Type in Smart timer dimming software program:
T1
T2
T3
T4
TIME**
06:00
07:00
11:00
---
LEVEL** 100%
70%
50%
70%
Dimming Level(%)
Operating Time(HH:MM)
**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level. Example: If a residential lighting application adopts D01-Type, when turning on the power supply at 6:00pm, for instance:
[1] The power supply will switch to the constant current level at 100% starting from 6:00pm. [2] The power supply will switch to the constant current level at 70% in turn, starting from 0:00am, which is 06:00 after the power supply turns on. [3] The power supply will switch to the constant current level at 50% in turn, starting from 1:00am, which is 07:00 after the power supply turns on. [4] The power supply will switch to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on.
The constant current level remains till 8:00am, which is 14:00 after the power supply turns on.
Ex: D02-Type: the profile recommended for street lighting
Set up for D02-Type in Smart timer dimming software program:
TIME** LEVEL**
T1 01:00 50%
T2 03:00 80%
T3 8:00 100%
T4
T5
11:00
---
60%
80%
Dimming Level(%)
Operating Time(HH:MM)
**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level. Example: If a street lighting application adopts D02-Type, when turning on the power supply at 5:00pm, for instance: [1] The power supply will switch to the constant current level at 50% starting from 5:00pm. [2] The power supply will switch to the constant current level at 80% in turn, starting from 6:00pm, which is 01:00 after the power supply turns on. [3] The power supply will switch to the constant current level at 100% in turn, starting from 8:00pm, which is 03:00 after the power supply turns on. [4] The power supply will switch to the constant current level at 60% in turn, starting from 1:00am, which is 08:00 after the power supply turns on. [5] The power supply will switch to the constant current level at 80% in turn, starting from 4:00am, which is 11:00 after the power supply turns on. The
constant current level remains till 6:30am, which is 14:00 after the power supply turns on.
Downloaded from Arrow.com.
File Name:ELG-200-C-SPEC 2022-02-11
150~200W Constant Current Mode LED Driver
ELG-200-C series
Ex: D03-Type: the profile recommended for tunnel lighting
Set up for D03-Type in Smart timer dimming software program:
T1
T2
T3
TIME**
01:30
11:00
---
LEVEL** 70%
100%
70%
Dimming Level(%)
Operating Time(HH:MM)
**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level. Example: If a tunnel lighting application adopts D03-Type, when turning on the power supply at 4:30pm, for instance: [1] The power supply will switch to the constant current level at 70% starting from 4:30pm. [2] The power supply will switch to the constant current level at 100% in turn, starting from 6:00pm, which is 01:30 after the power supply turns on. [3] The power supply will switch to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on. The constant current level remains till 6:30am, which is 14:00 after the power supply turns on.
Downloaded from Arrow.com.
File Name:ELG-200-C-SPEC 2022-02-11
LOAD (%)
150~200W Constant Current Mode LED Driver
ELG-200-C series
OUTPUT LOAD vs TEMPERATURE(Note.7)
100
80 230VAC input only
60
40
20
230VAC input only
-40
-25 0 10
20
30
50
60
70 (HORIZONTAL)
AMBIENT TEMPERATURE,Ta ()
LOAD (%)
100
80 230VAC input only
60
40
20
-40 -25 0
20
45
55
65
75
85 (HORIZONTAL)
Tcase ()
STATIC CHARACTERISTIC
100 90 80 75 70 60 50 40
100 120 140 160 180 200 240 250 260 270 280 305
INPUT VOLTAGE (V) 60Hz De-rating is needed under low input voltage.
PF
POWER FACTOR (PF) CHARACTERISTIC
Tcase at 75
1
0.98
0.96
110V (150W)
0.94
230V (200W)
277V (200W) 0.92
0.9
0.88
50%
60%
70%
80%
90%
100%
LOAD
TOTAL HARMONIC DISTORTION (THD)
700mA Model,Tcase at 75
20% 18% 16% 14% 12% 10%
8% 6% 4% 2% 0%
50% 60% 70% 80% 90% 100%
LOAD
115VAC (150W) 230VAC (200W) 277VAC (200W)
EFFICIENCY(%)
EFFICIENCY vs LOAD
ELG-200-C series possess superior working efficiency that up to 93% can be reached in field applications. 700mA Model, Tcase at 75
95
94
93
92
91
90
89
88
87
86
85
50%
60%
70%
80%
90%
100%
LOAD
110V (150W) 230V (200W) 277V (200W)
THD LOAD (%)
Downloaded from Arrow.com.
File Name:ELG-200-C-SPEC 2022-02-11
E L G - 2 0 0 - C 150~200W Constant Current Mode LED Driver
series
LIFE TIME
LIFETIME(Kh)
120
100
80
60
40
20
0
20
30
40
50
60
70
80
Tcase ( )
Downloaded from Arrow.com.
File Name:ELG-200-C-SPEC 2022-02-11
150~200W Constant Current Mode LED Driver
MECHANICAL SPECIFICATION
Blank-Type
244
233
300±20
220
ELG-200-C series
CASE NO.: 262A Unit:mm
300±20
AC/N(Blue) AC/L(Brown)
SJOW 17AWGx2C &H05RN-F 1.0mm2
tc
79
4-4.5
tc : Max. Case Temperature
SJOW 17AWGx2C &H05RN-F 1.0mm2
Vo-(Blue) Vo+(Brown)
71 53.8 32 37 37.5
A-Type
300±20
AC/N(Blue) AC/L(Brown)
SJOW 17AWGx2C &H05RN-F 1.0mm2
71 53.8
244 233 220
tc
79
32
4-4.5
tc : Max. Case Temperature
300±20
SJOW 17AWGx2C &H05RN-F 1.0mm2
Vo-(Blue) Vo+(Brown)
37 37.5
19
Downloaded from Arrow.com.
41.75
File Name:ELG-200-C-SPEC 2022-02-11
150~200W Constant Current Mode LED Driver
ELG-200-C series
AB-Type
300±20
AC/N(Blue) AC/L(Brown)
SJOW 17AWGx2C &H05RN-F 1.0mm2
71 53.8
244 233 220
tc
79
32
4-4.5
tc : Max. Case Temperature
300±20
SJOW 17AWGx2C &H05RN-F 1.0mm2
DIM+(Purple)* DIM-(Pink)** Vo-(Blue) Vo+(Brown)
37 37.5
19
B/DA/D2-Type
300±20
AC/N(Blue) AC/L(Brown)
SJOW 17AWGx2C &H05RN-F 1.0mm2
41.75
244 233 220
tc
79
4-4.5
tc : Max. Case Temperature
300±20
SJOW 17AWGx2C &H05RN-F 1.0mm2
DIM+(Purple)* DIM-(Pink)** Vo-(Blue) Vo+(Brown)
* DIM+ for B-Type DA+ for DA-Type PROG+ for D2-Type
* *DIM- for B-Type DA- for DA-Type PROG- for D2-Type
71 53.8 32 37 37.5
Downloaded from Arrow.com.
File Name:ELG-200-C-SPEC 2022-02-11
150~200W Constant Current Mode LED Driver
ELG-200-C series
3Y Model (3-wire input)
244
233
300±20
220
71 53.8 32
AC/N(Blue) AC/L(Brown) PE (Green/Yellow)
SJOW 17AWGx3C &H05RN-F 1.0mm2
tc
79
4-4.5
tc : Max. Case Temperature
Note1: Please connect the case to PE for the complete EMC deliverance and safety use. Note2: Please contact MEAN WELL for input wiring option with PE.
Installation Manual
Please refer to : http://www.meanwell.com/manual.html
SJOW 17AWGx2C &H05RN-F 1.0mm2
Downloaded from Arrow.com.
File Name:ELG-200-C-SPEC 2022-02-11