RadioMaster TX16S MKII Quick Start Guide

Introduction

Thank you for purchasing the RadioMaster TX16S MKII Multi-protocol radio system. RadioMaster is proud to bring this groundbreaking product to the market and would like to thank customers and the community for making this dream possible. The MKII version has had several improvements thanks to feedback from users. Please take a moment to read this quick start reference before using your new TX16S MKII radio.

Safety & Precautions

Many radio control models are equipped with powerful motors and sharp spinning propellers. Please exercise caution when working on models. Ensure power is disconnected from your models and remove propellers when performing maintenance.

Do not operate the TX16S MKII radio system under the following conditions:

• During bad weather or high wind conditions such as rain, hail, snow, storms, or electromagnetic events.
• Under limited visibility.
• In areas where people, property, powerlines, roads, vehicles, or animals may be present.
• If you are feeling tired or unwell, or under the influence of drugs or alcohol.
• If the radio or model appear to be damaged or not functioning correctly.
• In areas of high 2.4GHz interference or in locations where use of 2.4GHz radios is prohibited.
• When the battery in the TX16S MKII or the model is too low to function.

CAUTION!

The TX16S MKII is shipped with the most stable firmware at the time of manufacture. Please only update firmware if you are experienced and confident in updating system firmware. Incorrect updates may render the radio inoperable.

DO NOT charge 6.6v LiFE battery packs or Li-ion 18650 cells with a nominal voltage of 3.6v. Incorrectly charging the wrong battery type may lead to damage of the radio or fire.

Antenna Separation Distance: When operating your RadioMaster transmitter, please be sure to maintain a separation distance of at least 20 cm between your body (excluding fingers, hands, wrists, ankles, and feet) and the antenna to meet RF exposure safety requirements as determined by FCC regulations.

Regularly check the health and condition of your batteries and never leave your radio charging unattended. Always charge in a safe area away from combustible materials and surfaces. Do not charge if your radio becomes wet or damaged in any way. RadioMaster does not accept any liability for the use or misuses of this product.

Manuals and Firmware Downloads

The TX16S MKII is shipped with EdgeTX software installed as standard. To download the latest software and manual, please visit:

• RadioMaster Website

Further firmware information:

• EdgeTX: http://edgetx.org
• OpenTX: www.opentx.org
• ExpressLRS: https://www.expresslrs.org/2.0/
• Multi Protocol Module: https://www.multi-module.org/

Power Requirements

The TX16S MKII has built-in USB-C charging for 3.7v Lithium cells. The charging circuit is designed for 2x 3.7v Li-ion 18650 unprotected cells or 2x 3.7v Li-poly cells (2s 7.4v LiPO pack) only, with a nominal cell voltage of 3.7v and a maximum charge capacity of 4.2v.

Remote Control Overview

The TX16S MKII features a comprehensive layout of controls and ports:

• Switches: SF (2-Position), SE (3-Position), SB (3-Position), SA (3-Position), SH (Momentary), SG (3-Position), SC (3-Position), SD (3-Position).
• Dials/Sliders: LS (Slider Pot), S1, S2 Dials.
• Buttons: T1-T6 Trim Buttons, SYS Button, RTN Button, PAGE> Button, PAGE< Button, TELE Button, MDL Button, Power Button.
• Gimbals: Left Gimbal, Right Gimbal.
• Indicators: Power LED.
• Antenna: Located at the top.
• Handle: Integrated grip.
• 6-Position Buttons: Located on the handle.
• Speaker: Integrated for audio feedback.
• Menu Wheel: For navigation.
• Display: 4.3" Color Screen.
• Module Bay: JR compatible module bay.
• Grips: Changeable flat and raised grips are included.
• Ports: 3.5mm Audio out, USB-C port (for charging and firmware updates), Battery bay.

Model and Protocol Selection (Multi-protocol Module)

A wide variety of modules is available for TX16S MKII units with the 4-in-1 module. To find out whether a certain protocol would work with your radio, please visit:

• https://www.multi-module.org/

Note: Current protocols may be updated, and new protocols added, without prior notice.

To select a model and protocol:

1. Press and hold the MDL button and scroll to the MODEL SETUP page.
2. Under Internal RF, set the Mode to MULTI and select the RF Protocol/sub-protocol as desired.
3. Once the protocol is selected, the corresponding RF chip will be activated.

Key Functions:

• The Bind button starts the bind process. If a compatible receiver is in bind mode within range, it will bind to your receiver.
• Range mode cuts the RF output by a factor of 30, allowing for easy range testing.

Model and Protocol Selection (ELRS)

Bind Method:

1. Turn off the radio.
2. Cycle power to the receiver 3 times. The receiver LED will start blinking, indicating it's in bind mode.
3. Turn on the radio, enter the ExpressLRS LUA, and select Bind.
4. The receiver LED will now stay illuminated, signaling a successful bind process.

Support

Warranty and Repairs

Please retain your proof of purchase and contact the retailer you purchased your TX16S MKII from should you experience any problems with your radio hardware. Warranty is valid for one year from the date of purchase.

Specifications

Approved Battery Types

Approved for use:

• 2 x 3.7v Li-ION 18650 cells (7.4v using supplied tray)
• 2 x 3.7v Li-ION 21700 cells (Assembled as 7.4v 2s Battery pack)
• 2 x 3.7v Lithium-polymere cells (Assembled as 7.4v 2s Battery pack)

DO NOT use:

• 3.6v Li-ION cells
• 2S 6.6v LiFE Battery packs
• LiFEP04 cells

Using the built-in USB charger with incorrect battery types and voltage may cause damage to the remote control or fire.

Check the health and condition of the batteries regularly. Do not use damaged cells. Never charge your device unattended. Always charge in a safe area away from flammable materials. If the remote control gets wet or damaged in any way, do not charge it. RadioMaster is not responsible for any adverse consequences caused by using or misusing this device.

Declarations and Compliance

EU Simple Declaration of Conformity

RadioMaster declares that the radio equipment TX16S is in compliance with EU directives Directive 2014/53/EU. The full text of the declaration of conformity is available at the following website: www.radiomasterrc.com

Manufacturer: ShenZhen RadioMaster Co., Ltd, 4F Yang Tian Building, Area 72 Xing Dong community, Xin An Street, Bao An district, Shen Zhen city, Guangdong Province, China.

FCC Information

FCC ID: 2AV3G-TX16S

This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The full text of the declaration of conformity is available at the following website: www.radiomasterrc.com

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.

Antenna Separation Distance

When operating your RadioMaster transmitter, please be sure to maintain a separation distance of at least 20 cm between your body (excluding fingers, hands, wrists, ankles, and feet) and the antenna to meet RF exposure safety requirements as determined by FCC regulations.