PRISMXR Puppis S1 Lite Quick Start Guide

How to Stream (PrismPulse Mode)

To stream your PC content to your VR headset using PrismPulse Mode:

• Turn on your PC and VR headset.
• Select "PrismPulse" in the Wi-Fi settings of your VR headset.
• Depending on your VR headset, you can choose your preferred streaming method, such as Virtual Desktop (recommended), Steam Link, Quest Link, Pico Streaming Assistant, etc.

Wi-Fi Hotspot Mode

On the Home interface of the PrismXR Desktop App, you can switch the Puppis S1 Lite from PrismPulse Mode to Wi-Fi Hotspot Mode.

To connect:

• Select "PrismXR Hotspot" or "PrismXR Hotspot_5G" in the Wi-Fi settings of your device.

Visual Description: The PrismXR Desktop App interface displays options to switch between PrismPulse Mode and Wi-Fi Hotspot Mode. It also shows network connection status, region selection, and Wi-Fi settings for 2.4G and 5G networks, including SSID and password configuration.

Maintenance

Firmware Update

To ensure the best user experience, updating to the latest firmware version is highly recommended.

Note: Keep the Puppis S1 Lite connected to the internet during the update. The device will restart automatically after completion.

Steps to check for updates:

• Click "Puppis S1 Lite" to enter its interface.
• Click "Settings" to enter the Settings interface.
• Click "Check for Update" to see if a new firmware version is available.

Factory Reset

A factory reset may be necessary if you encounter connectivity or function issues.

Procedure:

• Press and hold the SET button ? for approximately 10 seconds, until all LED indicators blink red five times.
• The Puppis S1 Lite will restart automatically after the factory reset is complete.

Visual Description: A diagram illustrates the SET button on the Puppis S1 Lite and indicates pressing and holding it for 10 seconds, leading to LED indicators blinking red five times, signifying a factory reset.

Safety Instructions

Follow these basic guidelines for unpacking, installation, use, and maintenance of your electronic device:

• Avoid dropping the device.
• Do not disassemble the device.
• Avoid using or installing the product near water to prevent fire or shock hazards (e.g., near bathtubs, sinks, laundry tubs, or swimming pools). Do not expose the equipment to rain or moisture (e.g., wet basements).
• Ensure all ventilation openings are not blocked to prevent overheating.
• Do not insert any objects into the product's openings, as this can cause fire or electric shock by shorting internal components.
• Keep the product away from radiators and heat sources.
• Do not spill food or liquids on product components.
• Operating temperature should be between 0°C and 40°C.
• Ensure the power adapter meets the voltage and current specifications marked on the product's electrical ratings label.

RF Exposure Compliance:

To comply with FCC's RF exposure guidelines, install and operate this equipment with a minimum distance of 20cm between the radiator and your body.

Importer Information:

Company Name: PRISMXR PTE. LTD.

Address: 60 PAYA LEBAR ROAD #12-03 PAYA LEBAR SQUARE, SINGAPORE, 409051

Regulatory Statements

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment causes harmful interference to radio or television reception, users are encouraged to try correcting the interference by:

• Reorienting or relocating the receiving antenna.
• Increasing the separation between the equipment and receiver.
• Connecting the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consulting the dealer or an experienced radio/TV technician.

ISED RF Exposure Statement

This device complies with ISED RSS-102 RF exposure limits set forth for an uncontrolled environment. To avoid exceeding these limits, human proximity to the antenna shall not be less than 20 cm during normal operation.

The device is restricted to indoor use only when operating in the frequency ranges: 5180-5240MHz, 5260-5320MHz, 5500-5700MHz, 5745-5825MHz.

Declaration: PRISMXR PTE. LTD. declares that the radio equipment type P1431 is in compliance with Directive 2014/53/EU.

Frequently Asked Questions (FAQ)

Q: What should I do if Virtual Desktop or Quest Link can't find my PC?

A: This is often caused by firewall or network settings. Try these steps:

• Turn off the Windows firewall.
• Change your PC's network profile from "Public" to "Private".
• Check if your PC or Quest headset is using a VPN connection; disable it if so.

Q: What should I do if PCVR streaming is abnormal (e.g., lag or spikes)?

A: Troubleshoot using these steps:

• Connect your Puppis S1 Lite to the PrismXR Desktop App and click "Click to Start".
• On the One-Click Scan interface, click "Checkup".
• Follow the results to fix issues using the "Fix" button or the help guide.
• For wireless interference: Go to "Estimation" on the Dashboard, select the 5G band ?, and scan for a recommended channel. Then, in "Puppis S1 Lite Settings", switch to the recommended Wi-Fi channel and click "SUBMIT" to apply.

Q: What should I do if my Windows PC cannot connect to Puppis S1 Lite via the PrismXR Desktop App?

A: Follow these troubleshooting steps:

• Open "Control Panel" > "Network and Internet" > "Network Connections".
• Check if the "Puppis S1 Lite" network interface is enabled.
• If enabled, right-click on it and select "Status".
• Click "Details" to verify if it has obtained the correct IP address (e.g., 192.168.137.xxx).

Download and Install PrismXR Desktop App

Note: The PrismXR Desktop App is compatible with Windows 10 or 11 systems only.

To download and install the app:

• Open your browser and navigate to www.prismxr.com/pages/support-dev.
• Scroll down to "Downloads" and click on "PrismXR Desktop" to download and install it.
• Click on the "PrismXR" shortcut to launch the PrismXR Desktop App.

Set Up the Puppis S1 Lite

Notes:

• It takes about 1-2 minutes for the Puppis S1 Lite to boot up. Only the bottom LED indicator stays green during boot up. Do not operate the device until boot up is complete.
• If your PC is connected to your home router via an Ethernet cable, please disconnect it before proceeding.

Connection Steps:

• Connect your Puppis S1 Lite to a power source using the provided power adapter ?.
• Connect your PC to the LAN port of the Puppis S1 Lite using the included Ethernet cable.

Connect to the Internet

Method 1 (Recommended): Connect your Puppis S1 Lite to the internet by plugging an Ethernet cable from the LAN port of your home router into the WAN port of the Puppis S1 Lite.

Method 2: Connect your Puppis S1 Lite to the internet using a 2.4G Wi-Fi connection ?.

• Open the PrismXR Desktop App.
• Click "Click to Start" on the Home interface to connect to your Puppis S1 Lite.
• Switch the "Network Connection" from WAN (Recommended) to 2.4G Wi-Fi.
• Click "Wi-Fi Settings" to connect your Puppis S1 Lite to a 2.4G Wi-Fi network.
• Follow the on-screen instructions to complete the configuration.

Visual Description: Diagrams illustrate the physical setup: connecting the Puppis S1 Lite to power, connecting the PC to the Puppis S1 Lite's LAN port via Ethernet, and connecting the Puppis S1 Lite to the internet either via Ethernet (WAN port to router LAN) or 2.4G Wi-Fi. The PrismXR Desktop App interface is shown for selecting network connection type (WAN/2.4G Wi-Fi) and configuring Wi-Fi settings.

Set a Password (Optional)

Note: For the convenience of PCVR streaming, the default password for the Puppis S1 Lite is empty.

To set a password:

• Open the PrismXR Desktop App.
• Click "Click to Start" on the Home interface to connect to your Puppis S1 Lite.
• Set a password for your Puppis S1 Lite.

Visual Description: The PrismXR Desktop App interface shows fields for setting the SSID and password for the Puppis S1 Lite's Wi-Fi hotspot.