UltraPro In-Wall Smart Switch

About This Product

This document provides instructions for the UltraPro In-Wall Smart Switch, a Z-Wave certified wireless lighting control device. It can be used for single-pole or 3-way installations and integrates with Z-Wave home automation systems.

Model Numbers: ZW4009, 39354

Manufacturer: Jasco Products Company LLC

Website: www.ezzwave.com

For deals, registration, and feedback, visit byjasco.com/deals.

For installation videos and support, visit byjasco.com/39354i.

1. Features

• Can be added in multiple groups and scenes.
• Supports single-pole installation or use with up to four add-on switches (model 39356) in 3-way wiring configurations.
• Z-Wave certified for simple pairing and integrated home automation.
• Screw terminal installation requires wiring connections for line (hot), load, neutral, and ground. A traveler wire is required for 3-way or 4-way installations.
• Advanced features allow customization; visit www.ezzwave.com for a complete list of adjustable configurations.

2. Installation

WARNING — SHOCK HAZARD

Turn OFF the power to the branch circuit for the switch and lighting fixture at the service panel. All wiring connections must be made with the POWER OFF to avoid personal injury and/or damage to the switch. This device is intended for installation in accordance with the National Electric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada. If you are unsure or uncomfortable about performing this installation, consult a qualified electrician.

Single-Switch Wiring:

1. Shut off power to the circuit at the circuit breaker or fuse box. IMPORTANT! Verify power is OFF to the switch box before continuing.
2. Remove the wallplate.
3. Remove the switch mounting screws.
4. Carefully remove the existing switch from the switch box. DO NOT disconnect the wires.
5. Identify the switch terminals:
   • A. GROUND (Green/Bare wire)
   • B. LINE OR LOAD (Black wire to light fixture)
   • C. LINE OR LOAD (Black wire from electrical service panel/hot)
   • D. TRAVELER (Red/Other wire, only in 3-way installations)
   • E. NEUTRAL (White wire)
   Match these screw terminals to the wires connected to the existing switch.
6. Disconnect the wires from the existing switch. Label wires according to the previous terminal connection.

Wiring Information:

• This switch is rated for and intended to only be used with copper wire.
• Wire Gauge Requirements: Use 14AWG or larger wires suitable for at least 80° C for all connections (line, load, neutral, ground, traveler).
• Wire Strip Length: Strip insulation 5/8in. (16mm). Do not wrap wires around screws. Use only the enclosure's holes for insertion.
• UL specifies the tightening torque for the screws is 14Kgf-cm (12lbf-in).

Connecting Wires:

8. Connect the green or bare copper ground wire to the GROUND terminal (A).
9. Connect the black wire from the light to either LINE/LOAD terminal (B).
10. Connect the black wire from the electrical service panel (hot) to the other LINE/LOAD terminal (C).
11. Connect the white wire to the NEUTRAL terminal (E) (use a jumper wire if needed).

Diagram Description: The diagram shows wires being inserted into holes on the terminals labeled A (Ground), B (Line/Load), C (Line/Load), and E (Neutral). Wires should not be wrapped around screws.

12. Insert the switch into the switch box, being careful not to pinch or crush wires.
13. The switch must be independently mounted (vertical position only).
14. Mount the wallplate.
15. Reapply power to the circuit at the fuse box or circuit breaker and test the system.

Multi-Switch Wiring:

An add-on switch model 39356 is required for multi-switch installations. Refer to the add-on switch manual for more information.

3. Connection to a Z-Wave Network

1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
2. Once the controller is ready to add your device, press up on the toggle switch.

If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box or the QR code label on the product.

Z-Wave DSK: PIN: XXXXX, DSK: XXXXX-25651-22671-26939-47599-19612-25872-47752

4. Manual Control

The front panel toggle switch allows the user to turn the connected fixture ON/OFF.

• To turn the connected fixture ON: Press up on the toggle switch and release.
• To turn the connected fixture OFF: Press down on the toggle switch and release.

5. Cycle LED Light

An LED shines behind the toggle to act as a guide light or status indicator. Cycle through options by pressing up three times, then down once quickly.

• Option 1: LED is always OFF (default).
• Option 2: LED is always ON (illuminates switch in the dark).
• Option 3: LED is ON when the load is OFF (guide light in the dark).
• Option 4: LED is ON when the load is ON (indicates the switch is ON).

6. Removing and Resetting the Device

• Removing from Z-Wave Network: Follow the instructions for your Z-Wave certified controller to remove a device. Once the controller is ready, press up on the toggle.
• Returning to Factory Defaults: Quickly press the toggle up three times, then immediately press down three times.

Note: Factory reset should only be used if the network’s primary controller is missing or inoperable.

SmartStart: Products enabled for SmartStart can be added by scanning the QR code with a controller that supports SmartStart inclusion. The product will be added automatically within 10 minutes of being powered on.

7. Z-Wave Interoperability

This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters, increasing network reliability.

8. Specifications - Important!

• Model: ZW4009
• Power: 120VAC, 60Hz
• Signal (frequency): 908.4/916MHz
• Maximum loads: 960W incandescent, 1/2HP motor, or 1800W (15A) resistive.
• Range: Up to 150ft. line of sight between the wireless controller and the closest Z-Wave receiver module.
• Operating temperature range: 32-104° F (0-40° C).
• Enclosure: Type 1, independently mounted (vertical position only).
• Usage: For indoor use only.
• Specifications are subject to change without notice due to continuing product improvement.

9. Warranty

Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights and you may also have other rights which vary from state to state.

For warranty service, please contact Jasco Products Company's U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7AM – 8PM, M-F, Central Time, or visit www.byjasco.com.

10. FCC/IC Compliance

This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Important Note: To comply with FCC RF exposure compliance requirements, no changes to the antenna or device are permitted. Any change could result in the device exceeding RF exposure requirements and voiding user’s authority to operate the device.

Responsible Party - US Contact Information:

FCC — U2ZZW4009 | IC: 6924A-ZW4009

Jasco Products Company | Model: ZW4009/39354

10 E. Memorial Rd., Oklahoma City, OK 73114 | 1-800-654-8483

CAN ICES-3(B)/NMB-3(B)

11. Warnings and Cautions

WARNING

• RISK OF FIRE
• RISK OF ELECTRICAL SHOCK
• RISK OF BURNS

CONTROLLING APPLIANCES CAUTION:

• DO NOT EXCEED RATINGS.
• DO NOT USE TO CONTROL ANY DEVICE WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC.).
• DO NOT USE TO CONTROL RECEPTACLES.
• FOR INDOOR USE ONLY.

NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT EQUIPMENT

Z-Wave enabled devices should never be used to supply power to or control the ON/OFF status of medical and life-support equipment.

Association Command Class

This device supports Association Command Class (3 Groups):

• Association Group 1: Supports Lifeline, Binary Switch Report, Central Scene notification.
• Association Group 2: Supports Basic Set and is controlled by pressing the ON or OFF button with the local load.
• Association Group 3: Supports Basic Set and is controlled by double pressing the ON or OFF button.
• Each Association Group supports 5 total nodes.