HUTT C65 Robot Window Cleaner
Thank you for choosing the HUTT C65 window cleaning robot. Please read this manual carefully before use to ensure safety and full utilization of your HUTT cleaning product.
Product Overview
1.1 Component Name and Function
Power Button: Press and hold for 3 seconds to turn on/off. Press to pause/continue.
Voice Speaker: x 2
Status Indicator: Blue indicator: On. Flashing blue: Requires charging.
Nozzle: For spraying water.
Safety Rope and Power Cord: Connects the device and provides safety.
Water Inlet: For filling the water tank.
Water Tank: Holds the cleaning fluid.
Removable Rotating Base: (Do not remove under normal circumstances; place cloth directly.)
1.2 Parts List
- Main Unit
- Rotating Base (installed)
- Remote Control
- Cleaning Cloth
- Safety Rope
- Power Adapter
- Plug
- Nozzle
- Water Bottle
- User Manual
1.3 Introduction to Standard Operation Method
Installing the Rotating Base
If the rotating base is removed, reinstall it according to the position of the corresponding port indicated on the base label, ensuring each mounting is in place to avoid air leakage.
Replacing the Nozzle
- Check if the nozzle is clogged: If the device is on and cannot spray water in wet wiping mode, the device nozzle is clogged and needs replacement.
- Remove the nozzle: Pinch the blue part of the nozzle with pliers and pull it out directly.
- Install a new nozzle: Find a new nozzle from the accessory kit and install it by pressing it directly down.
Attaching the Safety Rope
Connect the fixed end of the "Y" shaped safety rope device to the safety rope, and the other end of the safety rope to a solid and immovable object.
Filling the Water Tank
- Pour water into the bottle: Fill the bottle with water and tighten the cap to prevent leakage. Note: The liquid used for filling must not be corrosive. For example: tap water, pure water, special glass cleaner, etc. If the operating temperature of the device is below 0°C, an antifreeze glass cleaner is required.
- Pour water into the water tank: Unscrew the small cap of the water bottle filled with water and align the narrow opening of the bottle with the water inlet of the window cleaning robot to fill the water tank. Note: After filling, immediately wipe off any spilled water from the body before using the device.
- Connect the water tank: After filling the water tank, cover the tank with the cap and check for leaks before use.
1.4 Cleaning Instructions
| Method | Description |
|---|---|
| Dry Wiping Method | Place the dry cleaning cloth on the rotating base. After starting the device, press the water spray button on the remote control to turn off the water spray function, and the device will switch to dry cleaning mode. |
| Wet Wiping Method | Method 1: Install the dry cleaning cloth on the base, the device is set to wet wiping mode by default after startup, and the water spray function is turned on. Method 2: After soaking the cloth, dry it by hand (drying to a humidity similar to that of clothes dried in a washing machine), and then install it on the base. |
| Cleaning Method for Dirty Glass with Large Particles | If there are hard particles or dust on the glass, there is a risk of scratching the glass. It is recommended to manually wipe the glass first, and then wipe it with this product. If manual wiping is not possible, it is recommended to wipe the glass twice with the device, the first time using the dry wiping method to reduce scratches, and then the wet wiping method for the second time. |
| Device Storage | After cleaning the device, drain the water from the tank. Replace the used cleaning cloth with a clean, dry one, or store the device without the cleaning cloth. After working in wet wiping mode, the device should be placed in a dry, ventilated, and cool place for 1-2 days to dry. |
1.5 Installation Instructions
Attaching the Cloth
Place a clean and dry cloth on the rotating base, smooth it out, and secure it in place.
Connecting to Power
Connect the power cord and the device adapter. Connect the power cord and the plug adapter. Connect the power cord to the power outlet.
Attaching the Safety Rope
Check if the safety rope is damaged. If the safety rope is intact and undamaged, perform the following steps. Hang the safety rope on a solid, secure, and immovable object, leaving sufficient length for the device's operation. When attaching, it may be advisable to wind 1-2 extra turns.
Starting the Device
Press and hold the power button for 3 seconds to turn on the device. Place the device away from the window frame. After ensuring the device adheres to the glass, release your hands, press the Start button, and the device will begin operation.
Removing the Device
After cleaning the window, pull the safety rope with one hand and hold the power button with the other hand for 3 seconds to turn off the device, then remove it. Note: If the device cannot be touched after cleaning the window, use the remote control to move the device to a location easily accessible by hand, and then remove the device according to the above steps.
1.6 Remote Control Operation Instructions
- Directional Buttons: Move up/down/left/right.
- Water Spray ON (Default Wet Wiping Mode): Sprays water.
- End Wiping Downwards: From the current position.
- Wiping Start/Pause/Continue: Starts, pauses, or continues the cleaning cycle.
- Restart Cleaning: Restarts the cleaning process.
- Spot Wiping: Performs spot cleaning.
2. Safety Precautions
| Classification | Content |
|---|---|
| 01 Environmental Protection Precautions | 1. Do not use in rainy weather or when the glass is wet or fogged. 2. The product should only be used for cleaning in household conditions at temperatures between 0-40°C. 3. If the ambient temperature is low or below 0°C, it is recommended to use an antifreeze glass cleaner. 4. If external high-altitude operation is required, set up safety warnings on the ground to prevent accidental personal injury. |
| 02 Precautions for the Surface Being Cleaned | 1. Do not use on cracked or damaged glass. 2. Use in an environment where the window frame width is at least 6 mm. 3. Ensure the window size is larger than 30*30 cm (height) and check if the window has a very narrow frame, chamfered frame, very thin frame, chamfered glass, no frame, or if the glass adhesive has unevenness, gaps, etc. In the above circumstances, it is not recommended to use the product or to use it under supervision, as these conditions may cause the product to fall. |
| 03 Storage Precautions | 1. The product should not be exposed to water. 2. Store the device and accessories in a place inaccessible to children. 3. Do not place the product outdoors or in places exposed to direct sunlight, high temperatures, humidity, or water. 4. Do not place the product with flammable substances such as oil, gas, or flammable paint. |
| 04 Operating Precautions | 1. Ensure the safety rope is not damaged and attach it to an immovable place. 2. Use a dry cloth. 3. Use on vertical glass, exercise caution when using on inclined glass under supervision. If necessary, use the remote control to operate the device during use. 4. Turn off the device before cleaning the surface of the device to avoid danger during operation. 5. Do not bring your fingers or any part of your body close to the rotating parts and openings of the device. 6. Use the product according to the user manual. If the fault cannot be removed, contact our customer service department and do not repair it yourself to avoid danger. 7. Children are not allowed to operate this product. |
| 05 Precautions for Operation and Use | 1. Before use, ensure the battery is fully charged. 2. Do not use third-party chargers or disassemble or modify the main unit, battery, or charger yourself. 3. Do not use the charger if it is damaged or faulty; contact our customer service department. 4. Keep the charger away from heat sources. 5. If the product needs to be transported, it is recommended to use the original packaging to transport the device after it has been turned off. 6. If the product will not be used for a long time, charge it fully, turn off the device, and store it in a cool and dry place. When storing, charge the battery at least once every 3 months to prevent failure due to over-discharge. 7. When charging, check if the device contacts are clean. Never leave the device unattended during use and charging. Ensure that the device can be quickly disconnected from the power source in an emergency. Never expose the device to high temperatures. Charge the device in a dry, well-ventilated place away from flammable materials, maintaining a clearance of at least 1m from other objects. Never cover the device during charging. Never use a charger, charging station, cables, etc., without the manufacturer's recommendation and certification. Take care of your property; the device is equipped with cells that are difficult to extinguish; equip yourself with a fire blanket. |
3. LED Indicators and Voice Prompts
| LED Diode | Voice Prompt | Resolution |
|---|---|---|
| Indicator lights up BLUE | After powering on, please fasten the safety rope. | Adapter connection and charging status are normal, and the device can operate normally. |
| Indicator flashes BLUE | Charging | The device is charging. Please charge for at least 20 minutes before use. |
| Indicator flashes RED | Low battery, please charge the device. | Low battery, charge for 20 minutes before use. |
| Connect to power | Connect the power cord. | |
| Low pressure | Check if the cleaning cloth is in place: the cleaning cloth should be placed flat and smooth on the rotating plates. Check if the glass is smooth: the surface for placing the device should be smooth without unevenness. Check if the glass is not warped. When wiping warped glass, air will leak. | |
| Gyroscope error, connect the device and restart. | Disconnect the adapter and restart the device. | |
| Barometer error, reconnect the device and restart. | ||
| Fan error, reconnect the device and restart. | ||
| Edge sensor error, reconnect the device and restart. | ||
| Wireless module error, reconnect the device and restart. |
4. Troubleshooting
| Problem | Solution |
|---|---|
| 01 The device moves downwards during operation. | Incorrect movement caused by excessive moisture in the cleaning cloth, and the device cannot return to normal operation after observation. Absorb moisture from the cloth repeatedly with paper towels. The cleaning cloth is dirty, replace it with a dry and clean one. The cleaning cloth slips because it is too dry. Spray the cloth with water properly, and the device can resume normal operation. |
| 02 The device cannot be touched by hand during disassembly and there is no remote control. | Pull the safety rope to the glass, slowly retract the device to a position where it can be reached by hand, and then remove the device. |
| 03 Cause of device leakage. | Check if the rotating table is in place. Check if the cloth is placed evenly. Replace the cloth with a clean one. |
| 04 Measures to take when the device does not move smoothly. | The glass or other cleaned surfaces are curved or have uneven surfaces, such as stickers, causing large-scale air leakage. Check if there are sticky objects on the glass. |
| 05 The device does not stop automatically after wiping the entire window. | The device needs to be disassembled directly. |
| 06 Accidental power failure. | The device's battery will maintain adhesion to the glass for at least 20 minutes and will sound an alarm. Disassemble the device or restore power as soon as possible. |
5. Technical Parameters
| Parameter | Value | Parameter | Value |
|---|---|---|---|
| Model | C65 | Battery Capacity | 650mAh |
| Rated Voltage | 24V | Adsorption Time | 30 minutes |
| Rated Power | 90W | Variable Frequency Suction Range | 2000-3800Pa |
| Noise | 75dB | Water Tank Capacity | 80ml |
| Dimensions | 295mm*145mm*85mm | Cleaning Speed | 0.05 m/s |
| Charging Current | 300mA | Minimum Working Area | 300*300mm |
6. Path Planning and Water Spraying
Automatic Cleaning Path:
- Place the device in the center of the window, away from the frame, and press the Start button. The device will automatically move upwards, then move left, and finally reach the upper left corner of the window.
- Upon reaching the upper left corner, the device will wipe the window from top to bottom in an S-shape.
- Depending on the shape of the window, the device will recognize the lower left or lower right corner of the window as the endpoint of wiping.
- After completing the wiping, the device will automatically move to a nearby starting point, which is convenient for disassembly.
Automatic Water Spraying Path:
- After startup, the device defaults to wet wiping mode, and the water spraying function is turned on.
- To turn off the water spraying function, use the remote control.
- The nozzle is located on the right side of the device. The device sprays water when moving to the right, but does not spray water when moving to the left.
Environmental Protection
Used electronic equipment marked in accordance with the European Union directive must not be disposed of with municipal waste. It is subject to separate collection and recycling at designated points. By ensuring its proper disposal, you prevent potential negative consequences for the natural environment and human health. The system for collecting used equipment complies with locally applicable environmental regulations for waste disposal. Detailed information on this matter can be obtained from the municipal office, the cleaning facility, or the store where the product was purchased.
The product meets the requirements of the EU's New Approach Directives concerning user safety, health protection, and environmental protection, which specify hazards that should be detected and eliminated.
This document is a translation of the original user manual created by the manufacturer.
Detailed information on warranty conditions from the distributor/manufacturer is available on the website: https://serwis.innpro.pl/gwarancja
The product must be regularly maintained (cleaned) by the user or by specialized service points at the user's expense and scope. In the absence of information on necessary periodic maintenance or service actions in the user manual, the user should regularly, at least once a week, assess the difference between the physical state of the product and a physically new product. In case of detecting or identifying any difference, promptly take maintenance (cleaning) or service steps. Failure to properly maintain (clean) and react upon detecting a difference may lead to permanent damage to the product. The guarantor is not responsible for damage resulting from negligence.
Importer: INNPRO
INNPRO Robert Błędowski sp. z o.o.
ul. Rudzka 65c
44-200 Rybnik, Polska
tel. +48 533 234 303
hurt@innpro.pl
www.innpro.pl
Producer:
Beijing Hutt Wisdom Technology Co., Ltd.
432, 4th Floor, Building 12, 8
Xinjiekouwai Street, Xicheng
District, Beijing, China
Safety Precautions
Before charging, check if the device contacts are clean. Never leave the device unattended during use and charging. Ensure that the device can be quickly disconnected from the power source in an emergency. Never expose the device to high temperatures. Charge the device in a dry, well-ventilated place away from flammable materials, maintaining a clearance of at least 1m from other objects. Never cover the device during charging. Never use a charger, charging station, cables, etc., without the manufacturer's recommendation and certification. Take care of your property; the device is equipped with cells that are difficult to extinguish; equip yourself with a fire blanket.
LI-ION Battery
The device is equipped with a LI-ION (lithium-ion) battery, which, due to its physical and chemical structure, ages over time and with use. The manufacturer specifies the maximum operating time of the device under laboratory conditions, where optimal operating conditions for the device exist, and the battery itself is new and fully charged. The actual operating time may differ from the declared time and is not a product defect but a product feature. To maintain maximum battery life, it is not recommended to discharge it below 3.18V or 15% of its total capacity. Lower values, such as 2.5V for the cell, will permanently damage it and are not covered by warranty. If the battery or the entire device is not used for more than one month, the battery should be charged to 50%, and its charge level should be checked cyclically every two months. Store the battery and device in a dry place, away from sunlight and freezing temperatures.
LI-PO Battery
The device is equipped with a LI-PO (lithium-polymer) battery, which, due to its physical and chemical structure, ages over time and with use. The manufacturer specifies the maximum operating time of the device under laboratory conditions, where optimal operating conditions for the device exist, and the battery itself is new and fully charged. The actual operating time may differ from the declared time and is not a product defect but a product feature. To maintain maximum battery life, it is not recommended to discharge it below 3.5V or 5% of its total capacity. Lower values, such as 3.2V for the cell, will permanently damage it and are not covered by warranty. If the battery or the entire device is not used for more than one month, the battery should be charged to 50%, and its charge level should be checked cyclically every two months. Store the battery and device in a dry place, away from sunlight and freezing temperatures.
