LED Under Cabinet Light User Manual

Product Profile

This LED Under Cabinet Light features adjustable brightness and color temperature, multiple working modes, and timer options. It is powered by USB charging.

• Features:
• Adjust brightness/color temperature button
• Switch/function mode button
• Remote control receiver
• PIR sensor/charging indicator

Working Modes:

• AUTO modes: Always on mode, Night mode, Day mode

Color Temperature:

• White Light
• Natural Light
• Warm Light

Timer Options:

• Timer can be set for 30/60 minutes and then automatically shuts off.

RGB Change Mode:

• Fade
• 11 Color lights

Function Description

• Button: On/off and mode switching. Press to enter constant light mode (induction function inactive). Press again to enter night induction mode (light flashes three times). Press again to enter all-day induction mode (light flashes twice).
• Button: Color temperature switching and brightness adjustment. Cycle through white light, warm light, natural light with each press. Long press to dim or brighten the light.

Motion Sensor Working Instructions

The product uses double induction of human body and light. When ambient light is insufficient and night sensing mode is set, the lamp will light up automatically when people enter the induction area. In all-day induction mode, it lights up whenever people enter the area.

• The light turns off automatically approximately 25-30 seconds after people leave the sensing area.
• The light stays on if a person remains within the sensing range.
• In sensing mode, the light will not turn on in a well-lit environment.
• Installation position (too low, too high, or blocked probe) can affect the sensing range. It is recommended to mount the light facing the side of passage for optimal effect.

Sensing Range:

• Distance: 10ft
• Angle: 120°

The sensing range is the area within 120° and 10 feet from the probe. Improper installation or blockage can affect sensitivity. The light automatically turns on when a person passes through a low-light area within the sensing range and turns off after 25-30 seconds of leaving the range.

Remote Control Operation Instructions

When using the remote control, the light automatically enters the always-on mode. Operation settings such as switching, timing, dimming, and brightness adjustment can be performed via the remote control.

• The remote control range is within 16 feet.
• Multiple products can be controlled simultaneously.
• Obstruction by objects will affect remote control sensitivity.

USB Charging

• Please turn off the light before charging and do not use it while charging.
• Please use the included charging cable to avoid charging failure.
• Charging State: Red light
• Fully charged: Green light

Power usage duration description: Power consumption time varies with usage conditions. Daily usage duration affects power consumption speed. Brightness decreases with power level; recharge the light when brightness is low.

Installation Description

1. Step 1: Place the iron plate on the magnetic mark area of the lamp body.
2. Step 2: Tear off the double-sided adhesive protective film on the iron plate.
3. Step 3: Place the lamp and iron plate in the desired position.

Warnings

WARNING: The battery is hazardous and shall be kept away from children.

WARNING: The battery can cause severe or fatal injuries in 2 hours or less if it is swallowed or placed inside any part of the body.

WARNING: Medical attention should be sought immediately if it is suspected the battery has been swallowed or placed inside any part of the body.

INGESTION HAZARD: DEATH or serious injury can occur if ingested. Swallowed button cell or coin battery can cause internal chemical burns in as little as 2 hours. KEEP new and used batteries OUT OF REACH OF CHILDREN. Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body. For treatment information call: [National Battery Ingestion Hotline number].

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.