LED Under Cabinet Light User Manual

Product Profile

This section provides an overview of the LED Under Cabinet Light, highlighting its components.

• Light board
• Remote control receiver
• Switch/function mode button
• Adjust brightness/color temperature button
• PIR sensor/charging indicator
• USB Charging port

Function Description

Details the operation of the buttons on the light fixture.

• Switch/Function Mode Button:
  • Press once: Enter constant light mode (induction function is inactive).
  • Press again: Enter night induction mode (light flashes three times).
  • Press again: Enter all-day induction mode (light flashes twice).
• Color Temperature & Brightness Button:
  • Press to cycle through color temperatures: white light, warm light, natural light.
  • Long press to adjust brightness (dim or brighten).

Motion Sensor Working Instructions

Information regarding the motion sensor's range and operation.

• Sensing Range: 10 feet distance, 120° angle.
• The sensing range is affected by installation position and potential blockages.
• The light automatically turns on when a person enters the sensing range in low-light conditions and turns off approximately 25-30 seconds after they leave.
• The light stays on if a person remains within the sensing range.
• In sensing mode, the light will not activate in well-lit environments.
• For optimal performance, mount the light facing the direction of passage.

Special Instructions for Motion Sensing Mode

Specifics on the dual induction (human body and light) and timing of the sensor.

1. The product features dual induction for human body and ambient light. In night sensing mode, the light activates only when ambient light is insufficient and a person enters the induction area. In all-day induction mode, it activates upon detecting a person.
2. The light automatically turns off approximately 25-30 seconds after the person leaves the sensing area.
3. The light remains on as long as a person is detected within the sensing range.
4. The light will not turn on if a person is detected in a well-lit environment while in sensing mode.
5. Installation height, position, and probe obstruction can affect sensing range. Mounting facing the side of passage is recommended for better results.

Remote Control Operation Instructions

How to use the included remote control.

• Using the remote control automatically engages the always-on mode.
• The remote control allows for switching, timing, dimming, and brightness adjustments.
• The remote control has an effective range of 16 feet and can operate multiple products simultaneously. Obstructions may affect sensitivity.

USB Charging

Instructions for charging the device.

• Turn off the light before charging. Do not use while charging.
• Use the included charging cable for charging.
• Charging State: Red light indicates charging.
• Fully Charged: Green light indicates the battery is fully charged.

Installation Description

Step-by-step guide for installing the light.

1. Step 1: Clean the surface where the light will be pasted and ensure it is dry. Note that oil stains can affect adhesive strength.
2. Step 2: Place the two mounting pieces on the back of the light body and align them with the built-in magnet positions.
3. Step 3: Peel off the adhesive tape from the mounting pieces and stick them to the desired location. Press firmly for over 10 seconds.

Power Usage Duration Description

Information on battery life and charging.

• Usage duration varies based on conditions and daily usage time.
• Brightness may decrease as power levels drop. Recharge the light when the brightness is low.

Safety Warnings

Important safety information regarding the battery and device.

• WARNING: The battery is hazardous and must be kept away from children.
• WARNING: Swallowing or internal placement of the battery can cause severe or fatal injuries within 2 hours. Seek immediate medical attention if this is suspected.
• WARNING: For treatment information, contact the National Battery Ingestion Hotline at 1-(800)498-8666.
• INGESTION HAZARD: Swallowed button cell or coin batteries can cause severe internal chemical burns in as little as 2 hours. Keep new and used batteries out of reach of children.

FCC Compliance Information

Details the device's compliance with FCC regulations.

FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.