Installation and Instruction Manual
Wireless Dimmer - DALI Version
Brand: HYTRONIK
Model: HBTD8200D
1. Technical Specifications
| Product type | Mains voltage | Rated load | Stand-by power | Operation frequency | Transmission power | Range (Typical) | Protocol | Operation temperature | Case temperature (Max.) | Storage temperature | Max. relative humidity | IP rating | Impulse withstand voltage | Duty type | PTI material group | Glow wire | Protection | Insulation material | EMC standard (EMC) | Safety standard (LVD) | Radio Equipment (RED) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bluetooth DALI Dimmer | 220~240VAC 50/60Hz | Max. 100mA, 50 LED Drivers | <0.5W | 2.4 GHz - 2.483 GHz | 4 dBm | 10~30m | Bluetooth 5.0 SIG Mesh | Ta: -20°C ~ +45°C | Tc: +75°C | -20°C ~ +60°C | 20~90% | IP20 | 2.5KV | S1 | Illa | Level 3, 850°C | Built-in protection provided | Class II Pollution degree 2 | EN55015, EN61547, EN61000-3-2, EN61000-3-3 | IEC 61058-1, EN 61058-1, IEC 61058-1-2 | EN 61058-1-2, AS/NZS 61058.1, EN300 328, EN301489-1, EN301489-17, EN62479 |
2. Download the App
Free App for set-up and commissioning.
Supports Bluetooth 5.0 SIG mesh.
Requires iOS 10.0 or later or Android 5.0 or later.
Web app/platform available at: iot.koolmesh.com
3. Dimming Interface Operation Notes
Switch-Dim
The provided Switch-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switches. Detailed Push switch configurations can be set on Koolmesh app.
| Switch Function | Push switch | Action | Descriptions |
|---|---|---|---|
| Simulate sensor | Short press (<1 second) |
| *Note: Short press must be longer than 0.1s to be valid. |
| Simulate sensor | Double push |
|
|
| Simulate sensor | Long press (≥1 second) |
|
|
4. Installation
Warnings:
- Installation must be carried out by a qualified engineer in accordance with local regulations.
- Disconnect power supply before installing.
- Ensure environmental conditions are suitable for electronic equipment.
Device Connections and Mounting:
Wiring Terminal Block: A diagram shows a small electronic module with clearly labeled connection terminals: "DA+", "DA-", "L", "N", "S1", and "S2". These are typical for DALI and switch control inputs.
Dimensions: A rectangular diagram illustrates the physical dimensions of the device. The main body is approximately 46mm in width and height, with a depth of 22mm.
Typical Switch Box Mounting: Two illustrations show how the device can be mounted within a standard electrical switch box. One shows a side view of the device fitting into a recessed box, and the other shows a front view of the device installed flush with a wall plate.
Wire Preparation: A close-up diagram displays a terminal block with screw clamps. It indicates the acceptable wire gauge range for connection is 0.75 - 4mm², with a recommended stripping length of 8mm for proper insertion.
5. Additional Information / Documents
- For detailed product features and functions, refer to www.hytronik.com/download → knowledge → Introduction of App Scenes and Product Functions.
- For precautions regarding Bluetooth product installation and operation, refer to www.hytronik.com/download → knowledge → Bluetooth Products - Precautions for Product Installation and Operation.
- Data sheets are subject to change without notice. Always refer to the most recent release on www.hytronik.com/products/bluetooth-technology → Bluetooth Dimmers.
- For Hytronik standard guarantee policy, refer to www.hytronik.com/download → knowledge → Hytronik Standard Guarantee Policy.
Subject to change without notice.
