Your new ToggleLinc™ On/Off Switch allows you to remotely control any light in your home at the touch of a button. This guide provides quick start instructions for installation and operation.
Preparation
Installation should be performed only by a qualified electrician or a homeowner who is familiar and comfortable with electrical circuitry. If you have any questions regarding installation, consult an electrician. Software such as HouseLinc™ 2 can simplify INSTEON device setup and management. For setup questions, contact the INSTEON Support Line.
Tools Needed:
- Flathead and Phillips screwdrivers
- Wire cutter/stripper
- Voltage tester to identify wires inside the junction box
Installing ToggleLinc (Typical 2-Way Circuit)
Note: For multi-way circuit installation, refer to the Owner's Manual.
- At the circuit breaker or fuse panel, disable the circuit supplying power to the switch.
- Remove the faceplate from the existing switch, unscrew the switch, and pull it out from the junction box.
- Disconnect the wires from the switch you are replacing and ensure you have 3/8" of bare wire on the ends.
- Refer to Figure 1 to identify and connect the Line, Load, Neutral, and Ground wires to the INSTEON device. If wire colors do not match the diagram, verify wire identification before connecting. Note: Mechanical switches do not utilize Neutral wires, but they are usually available in the back of the switch box.
- Ensure all wires are firmly attached and no exposed copper is visible, except for the Ground wire.
- Orient ToggleLinc with the Set button at the bottom, gently place it into the junction box, and screw it into place.
- Enable power to the fixture from the circuit breaker or fuse panel.
- Test that ToggleLinc is working properly by turning the light on and off.
- Reinstall the faceplate.
Figure 1: Wiring Diagram Description
Figure 1 illustrates the wiring connections for the ToggleLinc switch. It shows how to connect the Line wire (power source), Load wire (to the light fixture), Neutral wire (required for the device, often present in the box), and Ground wire (safety connection) to the corresponding terminals on the INSTEON device.
Using ToggleLinc
Tap the toggle [Up Arrow] to turn your light on.
Tap the toggle [Down Arrow] to turn your light off.
Using ToggleLinc as an INSTEON Controller
- Press and hold the ToggleLinc Set button until the unit emits an audible beep (about 3 seconds). The ToggleLinc Status LED will begin blinking. You have 4 minutes to complete the next step.
- Select the INSTEON device you wish to control and activate its linking mode. ToggleLinc will emit a double-beep, and its Status LED will stop blinking and turn on solid.
- Confirm the link by pressing the ToggleLinc toggle up and down. The device controlled by ToggleLinc should respond appropriately.
Using ToggleLinc as an INSTEON Responder
- Select an INSTEON-compatible controller and activate its linking mode. You have 4 minutes to complete the next step.
- Press and hold the ToggleLinc Set button until the unit emits a double-beep (about 3 seconds).
- Confirm the link by tapping the On and Off buttons on the controller you just linked to ToggleLinc. The device controlled by ToggleLinc should respond appropriately.
Complete Instructions, Troubleshooting, and Tech Support
For complete instructions and troubleshooting, refer to the Owner's Manual: http://wiki.smarthome.com/index.php?title=2466S_Manual
Contact INSTEON Support Line at 800-762-7846.
For general contact information, visit: http://www.smarthome.com/contactus.html
Limited Warranty
INSTEON warrants this product to the original consumer for a period of 2 years from the date of purchase. This warranty covers defects in material and workmanship, ensuring the product performs in substantial conformity with its Owner's Manual. The warranty does not apply to defects caused by misuse or neglect. Product protected under U.S. and foreign patents. Visit www.insteon.com for patent information.
© 2012 INSTEON, 16542 Millikan Ave., Irvine, CA 92606
