Sealey Axle Stands (Pair)

Introduction

All steel stand with pin and chain load support. All models manufactured to rigorous safety standards. Sold in pairs.

Specification

Safety

WARNING!

DO NOT OVERLOAD AXLE STANDS BEYOND RATED CAPACITY. OVERLOADING CAN CAUSE DAMAGE TO, OR FAILURE OF, THE AXLE STANDS. POSITION LOAD ON CENTRE OF CRUTCH/SADDLE ONLY. ALWAYS USE STANDS IN PAIRS ON HARD LEVEL SURFACE CAPABLE OF SUSTAINING THE LOAD. USE OF STANDS ON OTHER THAN HARD LEVEL SURFACES CAN RESULT IN LOAD INSTABILITY AND POSSIBLE LOSS OF LOAD. DO NOT USE ON TARMACADAM. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO AXLE STANDS, LOSS OF LOAD RESULTING IN PROPERTY DAMAGE, SERIOUS PERSONAL INJURY OR LOSS OF LIFE.

DANGER!

GREAT CARE MUST BE TAKEN TO ENSURE YOU LOWER THE VEHICLE (OR OTHER LOAD) SLOWLY AND CAREFULLY ONTO THE CENTRES OF THE CRUTCH/SADDLE OF THE AXLE STANDS.

• ✔️ Use only as specified by the manufacturer.
• ✔️ Ensure the load does not exceed the maximum capacity as marked on the axle stand, per pair.
• ✔️ Use no more than a single pair of stands either on the front, rear or one side of the vehicle. Use in pairs.
• ✔️ No alterations or modifications shall be made to this product.
• ✔️ Use on a hard, level surface, e.g. concrete. Do not use on uneven ground or tarmacadam.
• ✔️ Securely chock wheels in contact with the ground. Before jacking and placing the stands, apply vehicle handbrake (put automatics in 'Park').
• ✔️ Make sure that each stand is securely located under a strong point on the vehicle; consult the vehicle manufacturer's handbook for guidance. Ensure that height adjust locking mechanism is fully located before applying any load to the axle stand.
• ✔️ Ensure that the load is located centrally on the saddle, and that the weight is directed through the vertical axis of the stand.
• ✔️ Exercise extra care when using with a three wheeled vehicle or a trailer. Refer to vehicle manufacturer's instructions.
• ✔️ Once vehicle is supported, ensure that the vehicle and stands are stable before starting work. Ensure that it is not possible for the vehicle to move before commencing any work.
• ✔️ Inspect stands before each use. DO NOT use if they show signs of damage. DO NOT use if it is suspected that they have been overloaded.
• ✔️ Before commencing any work or going beneath the vehicle, undertake a risk assessment. Ensure that a responsible person is aware of the work about to be undertaken.
• ✔️ Replace any labels on the axle stand should they become unreadable. This applies in particular to any warning or operation instruction labels. If replacement labels are required, contact your Sealey stockist.
• ❌ DO NOT use axle stands on the highway, or anywhere else if it is deemed to be unsafe.
• ❌ DO NOT push or twist the vehicle/load whilst it is supported on stands.
• ❌ DO NOT mix components between stands. Use only as supplied.
• ❌ DO NOT allow children or animals in the vicinity of a vehicle supported on axle stands.
• ❌ DO NOT leave a vehicle on axle stands in an area that could be considered a hazard to others or property.

FOLLOW STEPS 1, 2, AND 3 TO CORRECTLY PLACE VEHICLE / LOAD ONTO AXLE STANDS.

Diagram illustrating correct procedure for placing vehicle on axle stands. Step 1 shows wheels being chocked. Step 2 shows a vehicle being raised by a jack. Step 3 and 3A show correct placement of axle stands under vehicle support points. Three examples of incorrect placement are shown with red crosses.

STEP 1: Securely chock wheels that are in contact with the ground.

STEP 2: [Image depicts a vehicle being raised by a hydraulic jack.]

STEP 3: Correct placement of axle stands under vehicle support points. Examples of incorrect placement are shown.

[Correct Placement Example 1: Axle stand correctly positioned under a vehicle chassis point.]

[Incorrect Placement Example 1: Axle stand positioned incorrectly, not under a solid support point.]

[Incorrect Placement Example 2: Axle stand positioned at an angle, not vertically.]

[Incorrect Placement Example 3: Axle stand positioned on an unstable surface.]

Operation

1. 4.1. Refer to vehicle manufacturer's instructions for recommended support points.
2. 4.2. Check that the points are in good condition.
3. 4.3. Ensure the vehicle brake is on (or in park mode) and wheels are chocked.
4. 4.4. Adjust height of stand to correspond with the raised vehicle.
5. 4.5. Check that the locking pin is correctly pushed all the way through the centre column and out of the other side, then position stands under vehicle at points recommended by vehicle manufacturer.
6. 4.6. Lower the load onto stands carefully and slowly. Ensure the load bearing points sit in the center of the stand saddle and check that the stands are stable.
7. IMPORTANT: Ensure that there are no objects or persons that could impede the safe lowering of the vehicle onto the stands.
8. 4.7. To remove stands, jack vehicle slightly so that stand can be removed.
9. 4.8. After use, hold the centre column (fig.1.1) firmly when removing the locking pin (fig.1.3). Failure to do so will allow the center column to fall freely through the main centre tube (fig.1.2) which could be dangerous.
10. WARNING! Ensure you follow all instructions carefully. Failure to note these warnings may cause damage, serious injury or loss of life.
11. 4.9. Before each use check to ensure stands and stand welds are not cracked, and that there are no missing and/or damaged parts.
12. WARNING! Any stand that appears to be damaged in any way must be removed from service immediately.

Diagram of an axle stand, labelled with key components: 1. Centre column, 2. Main centre tube, 3. Locking pin.

Maintenance

• 5.1. Ensure the locking pins are in good order and condition.
• 5.2. Owing to the potential hazards associated with these stands, do not misuse, or make any modification to the stands or components.
• 5.3. It is the responsibility of the stand's owner to ensure the operator has read these instructions, and that the operator is familiar with the stand's use and limitations.

Environmental Protection

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Product Information & Support

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on technical@sealey.co.uk or 01284 757505.

Important: No Liability is accepted for incorrect use of this product.

Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Parts support is available for this product. Please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

Phone: 01284 757500 | 01284 703534

Email: sales@sealey.co.uk

Website: www.sealey.co.uk