Holoscope User Manual

Warnings

1. Do not bend or twist the power cable too much; otherwise, the power cable may be damaged and a fire may occur.
2. Do not allow the machine to come into contact with rain or other liquids.
3. Do not use or store the machine in high temperature, high pressure, and strong magnetic field, dusty and humid environment.

Attention

1. Install the host securely to avoid falling; the power cable may be damaged and a fire may occur.
2. Please install the product in a place that cannot be touched by human hands, or buy a protective cover to avoid injury.
3. Stable installation: Ensure that the 3D fan will not loosen and fall off during use. After the installation, you can shake the 3D fan vigorously to check whether there is a rocking phenomenon.

Common Faults and Maintenance

1. The device cannot be turned on after being plugged in, and no screen is displayed. Check whether the power supply is normal. After the power supply is powered on, observe whether the power indicator is on.
2. After the device is started, the screen is abnormal or the whole light bar is not on. Check whether the screws are not tightened and whether there are foreign objects in the connector.
3. A black circle appears after the device has been running for a period of time. Because there will be dust and stain on the surface of the lamp bead when the equipment is running, clean the surface of the lamp bead with a soft dry cloth, and usually clean the dust on the lamp board regularly to achieve the most ideal display effect.
4. The following situations do not belong to the scope of free warranty: unauthorized disassembly, maintenance, equipment water, oxidation, and other artificial damage.

Product Specifications and Parameters

Two blade advertising machine

Installation Demonstration

A diagram shows the components of the Holoscope: ① Power port, ② LED lamp bead, ③ Infrared signal lamp, ④ Card slot, ⑤ U-shaped pendant.

1. Insert the two blades into the host port, align the six screws with the screw holes, and fix the indicator securely. Otherwise, the indicator strip may fall off.
2. For wall mounting, insert the screws through the wall-mounting holes, align them with the expansion screw tube, and drive them into the appropriate positions.

Installation Instructions (四叶机器展示)

1. Insert the fan blades into the unit in pairs (A to A, B to B), then tighten 12 screws into the screw holes to secure them. Make sure they are tight or else the light strip may fall off. Installation is complete!
2. When installing the wall mount, just screw in the screws through the mounting block and into the right spot.
3. Align the U-shaped hanger at the bottom of the host, then push it down and screw the top of the U-shaped hanger on the machine hanger with a small screw to complete installation.

Remote Control Introduction

A diagram illustrates the remote control functions:

• Turn on
• RUN
• STOP (Power Off)
• Single cycle
• Switch to the previous screen
• Switch to the next screen
• Stop playing
• Reduce brightness
• Increase brightness
• Angle correction to the left
• Angle correction to the right

Scan and Download the APP

QR codes are provided for Android and iOS app downloads.

1. Search for Holoscope in the APP store for software download or contact the distributor for download. After downloading, open the app permission and use it.

Mobile APP Transmits Video

1. After the device is turned on, a WiFi signal will be established. Open the WiFi screen on your phone's Settings and search for WiFi names beginning with 3D-P, for example: 3D-PXXXXXXXX. The default password of the WiFi hotspot is 12345678.

Screenshots illustrate connecting to the WiFi network and the app interface.

If a message is displayed indicating that the WLAN cannot be connected to the network, you must select "Stay connected". And the first time to open the APP prompt, select "Continue trying to use wireless LAN".

Follow "Figure 1 (Android)" or "Figure 2 (IOS)".

Figure 1 (Android) and Figure 2 (IOS) show:

1. Click Transfer → 2 Video → 3 Select Upload video → 4 Confirm content → 5 Upload process → 6 Upload 100%

Steps for uploading video:

1. Click "Transfer"
2. Click "Video”
3. Select the video you want to upload
4. Click "OK"
5. Uploading
6. Transmission complete

The video transfer has been successful. If you need to replace the video or add more content, you have done so successfully without having to go through the next steps.

Connect the Bluetooth Speaker

1. Click on the APP to set "Bluetooth Settings" (the passwordless Bluetooth speaker must be used, and the transmitted video must have specific sound).
2. Bluetooth Settings: Turn on Bluetooth → Wait for automatic search for Bluetooth speaker → Connected (video must have specific sound).

Screenshots show the process of connecting a Bluetooth speaker.

Text LOGO Making

A workflow is shown for creating text logos:

1. Click design
2. Save
3. Back to page transfer
4. Select Local
5. Select video
6. In transmission

Instructions for using the PC:

Download link: http://bg.holoscope.tech/sh/apk/app/getLastAPK/0

After the device is powered on, the WiFi signal will be established. Open the WiFi interface of the computer and search for the name of WiFi beginning with 3D-P, for example, 3D-PXXXXXXXX. The default password of WiFi is 12345678. Enter password, Click join.

Download Software Connection → Connect to WIFI

Screenshots show connecting to WiFi on a PC and the Holoscope software interface.

The PC transmits the video:

1. Open software → Select machine model → Open
2. Select the video you want to upload
3. Start transmission
4. Wait for transmission