OPERATION MANUAL
⚠️ NOTE: Tasmota is not a commercial product and support is limited. You must be willing to independently investigate and resolve potential issues.
Detailed information about connection, changing settings and modifications is presented on the website " https://tasmota.github.io/docs/ "
Description
The NOUS L1t smart Wi-Fi switch with Tasmota open software installed (hereinafter referred to as the smart switch) is designed to organize automatic and manual lighting shutdown in the room, through remote access via a Wi-Fi network, using a smartphone or from a personal PC via the Web interface. Communication with the smart switch is configured via a Wi-Fi network, for which a wireless Wi-Fi adapter is used. It is equipped with touch buttons and a global indication of the device's status. Also equipped with a solid-state relay.
⚠️ ATTENTION: The connection of the smart switch to the Wi-Fi network cannot be guaranteed in all cases, as it depends on many conditions: the quality of the communication channel and intermediate network equipment, the brand and model of the mobile device, the version of the operating system, etc.
Precautions
- Read this manual carefully.
- Use the product within the temperature and humidity limits specified in the technical data sheet.
- Do not install the product near heat sources such as radiators, etc.
- Do not allow the device to fall and be subject to mechanical loads.
- Do not use chemically active and abrasive detergents to clean the product. Use a damp flannel cloth for this.
- Do not overload the specified capacity. This may cause short circuit and electric shock.
- Do not disassemble the product yourself - diagnostics and repair of the device must be carried out only in a certified service center.
- Please contact the seller for a replacement if there is damage caused by shipping.
Design and Controls
The NOUS L1t features touch buttons and indicators for status and network connection.
| No. | Name | Description |
|---|---|---|
| 1 | Indicator/Button | Shows the current status of the device / A short press of the button switches USB "ON" "OFF". |
| 2 | Network indicator | Indicates the status of the network connection. |
Diagram Description: A visual representation of the switch shows two key points: (1) the Indicator/Button and (2) the Network indicator.
Installation
The smart switch is mounted in a regular socket.
Installation Procedure:
- Remove the outer panel.
- Connect the smart switch as shown in the electrical diagram.
- Install the smart switch in the socket, then install the external panel.
- When the installation is complete, the device is ready to use.
⚠️ Importantly: Make sure that the Wi-Fi network is stable and has a sufficient level in the chosen installation location.
Diagram Description: An electrical diagram illustrates the wiring connections labeled 'N' (Neutral) and 'L' (Live) for the switch. Dimensions are provided as 3.4x3.4x1.39 inches.
Connection
A smartphone or PC is required to connect the Nous L1t smart switch.
The procedure for connecting the smart switch to the Wi-Fi network:
- Make sure that the frequency range of the network to which the device will be connected is 2.4 GHz, as the smart switch is not designed to work with 5 GHz Wi-Fi networks.
- Connect the smart switch to the network. The access point "tasmota-xxxxxxxx" should appear in the list of networks on your PC. If the access point is not detected, perform a "RESET" according to point 11.
- Connect to the hotspot "tasmota-xxxxxxx".
- After connecting to the access point, the browser should automatically open to 192.168.4.1. If it does not, manually enter 192.168.4.1 in the browser's address input field.
- On the open page, select your access point and enter its password in the field below, then click "Save".
- When the connection is complete, the inscription "Successfully connected to Wi-Fi" and the IP address of your device on the network will appear.
- Connect to your Wi-Fi network and navigate to the address specified in point 6.
- The smart switch is ready to use. The template and rules are already activated.
Configuration
The template must be entered in the "Template" field, check the "Activate" box, and save the changes.
Template JSON: {"NAME":"NOUSL1T", "GPIO":544,0,1,32,0,0,0,0,0,224,288,0,0,0], "FLAG":0,"BASE":1}
Diagram Description: The Tasmota configuration interface is shown, allowing users to input the template, activate it, set web admin passwords, enable MQTT, define device names, and select emulation modes (None, Belkin WeMo, Hue Bridge).
Resetting to Factory Settings
To reset the smart switch to factory settings, follow these steps:
- Plug and unplug the device 6 times, leaving it on for the 7th time. The LED should start flashing, indicating the smart switch is ready to be connected again.
- Alternatively, if you have access to the web interface, type "reset 1" in the console and press "enter".
Integrations
Tasmota is a highly extensible and flexible application that can be integrated with various platforms and services, including:
- Alexa
- AWS IoT
- Domoticz
- Home Assistant
- Homebridge
- HomeSeer
- IP Symcon
- KNX
- NodeRed
- nymea
- OctoPrint
- openHAB
- Otto
- IOBroker
- Mozilla WebThings Adapter
- SmartThings
- Tasmohab
- Homematic ip
- and others.
For more information, see: https://tasmota.github.io/docs/Integrations/
Tasmota Documentation - Tasmota
