Redmi Pad SE 8.7 Quick Start Guide

Introduction

Thank you for choosing the Redmi Pad SE 8.7 tablet.

Start the device by pressing and holding the power button. Configure the device according to the on-screen instructions.

For more information, visit our official website: www.mi.com/global/service/userguide

Device Overview

The Redmi Pad SE 8.7 tablet features the following:

• SD Card Slot: Located on the top edge.
• Volume Buttons: Located on the side edge.
• Power Button: Located on the side edge.
• USB Type-C Port: Located on the bottom edge for charging and data transfer.
• Speakers: Located on the bottom edge.

Important Safety Information

General Warnings

• Improper use of the battery can cause an explosion hazard. Dispose of used batteries according to instructions.
• Prevent possible hearing damage by avoiding listening for long periods at high volume.

For more safety information and precautions, visit: www.mi.com/en/certification

Safety Guidelines

• Read all the following safety information before using the device.
• Using unauthorized cables, power adapters, or batteries may cause fire, explosion, or other hazards. Use only approved and compatible accessories.
• The operating temperature for this device is 0–40 °C. Using the device at other temperatures may damage it.
• If the device has a built-in battery, do not attempt to replace it yourself.
• Charge the device only with the supplied or approved cable and power adapter. Using other adapters may cause fire, electric shock, or damage.
• When charged, unplug the adapter from both the device and the power outlet. Do not charge for more than 12 hours.
• The battery must be recycled or disposed of separately from household waste. Improper use may cause fire or explosion. Dispose of or recycle the device, its battery, and accessories according to local regulations.
• Do not disassemble, puncture, crush, or incinerate the battery. If the battery is unusually shaped or damaged, stop using it immediately.
• Avoid short-circuiting the battery, which can cause overheating and burns or other injuries.
• Do not use the battery in a hot environment; overheating can cause an explosion.
• Do not disassemble, puncture, or crush the battery to prevent leakage, overheating, or explosion.
• Do not incinerate the battery to prevent fire or explosion. If the battery is unusually shaped or damaged, stop using it immediately.
• The battery must not be removed or modified by yourself. Only an authorized service center may remove or repair it.
• Keep the device dry.
• Do not attempt to repair the device yourself. Contact customer support or an authorized service center if any part is not functioning properly.
• Connect other devices according to their user manuals. Do not connect incompatible devices.
• Ensure the power adapter socket is easily accessible.

Safety Precautions

• Comply with all applicable laws and regulations that restrict tablet use in certain situations and environments.
• Do not use the tablet at service stations, in potentially explosive environments (e.g., refueling areas, below deck on ships, fuel/chemical storage), or areas with chemicals or particles (e.g., grain, dust, metal powders). Follow signs instructing you to turn off wireless devices. Turn off the tablet in blasting areas or where two-way radios or electronic devices are required to be switched off.
• Do not use the tablet in hospital operating rooms or intensive care units. Always follow hospital and health center rules. If using a medical device, consult your doctor and the manufacturer to check for interference.
• Keep a distance of at least 15 cm between the tablet and pacemakers to avoid potential interference.
• Do not use the tablet near hearing aids, cochlear implants, or similar devices to avoid interference.
• Observe airline safety regulations and turn off the tablet on board when requested.
• When driving, comply with applicable traffic laws.
• Do not use the tablet outdoors during thunderstorms to avoid lightning strikes.
• Do not use the tablet in wet conditions (e.g., bathrooms) to prevent electric shock, injury, fire, or charger damage.
• Connect the Redmi Pad SE 8.7 to a computer using a USB cable.
• Use the supplied USB cable with a Mi brand charger and connect to an extension cord.
• You can also use other chargers that comply with USB2.0 or higher protocol standards and meet relevant safety standards (e.g., IEC 60950, IEC 62368-1).
• The product accepts chargers with a maximum power of 18W. Maximum voltage should not exceed 9V and maximum current should not exceed 2A. Using chargers that do not meet these requirements may damage the product and compromise safety.

Security Statement

Update the tablet's operating system via the internal software update function or by visiting an authorized service center. Updating software by other means may damage the device or cause data loss, security issues, or other hazards.

For optimal charging speed, use a charger with an input power of 10-18W (USB PD fast charging).

EU Regulations

Declaration of Conformity for Radio Equipment Directive

Xiaomi Communications Co., Ltd. hereby declares that this tablet with Bluetooth and Wi-Fi functions, model 24075RP89G, complies with the essential requirements and other provisions of Directive 2014/53/EU. The full EU Declaration of Conformity can be read at: www.mi.com/en/certification

Information on Exposure to Radiofrequency Energy (SAR)

This device complies with the SAR exposure limits for the general population (local 10g SAR for the trunk, limit: 2.0 W/kg) as defined in Council Recommendation 1999/519/EC, ICNIRP guidelines, and the Radio Equipment Directive (2014/53/EU). During SAR testing, the device was set to its highest transmission power level for each frequency band.

When carrying the device on your body, use a belt clip or holster that does not contain metal parts. SAR exposure limits have not been tested or certified with accessories containing metal, and the use of such accessories should be avoided.

Certification Information (Maximum SAR Value)

• SAR 10g limit: 2.0 W/kg
• SAR value: body: 0.995 W/kg (distance 0 mm).

Regulatory Information

This device can be used in all EU member states. Comply with national and local regulations of the place of use.

This device is restricted to indoor use when operating in the 5150–5350 MHz frequency range in the following countries: AT, BE, BG, HR, CY, CZ, DK, EE, FI, FR, DE, EL, HU, IE, IT, LV, LT, LU, MT, NL, PL, PT, RO, SK, SI, ES, SE, UK(NI), IS, LI, NO, CH, TR.

Wi-Fi connectivity (including frequency bands, standards, and functions certified according to IEEE 802.11) may vary based on regional availability and network support. This function may be added wirelessly as available.

2.4 GHz band restrictions: Norway: this provision does not apply to the geographical area within 20 kilometers of Ny-Ålesund.

Ensure that the power adapters used comply with the regulations of the destination country and international/regional safety standards.

Frequency Bands and Power

This tablet operates in the EU on the following frequency bands and with maximum radio-frequency power:

• Bluetooth: 20 dBm
• Wi-Fi 2.4 GHz: 20 dBm
• Wi-Fi 5 GHz: 5150–5250 MHz: 23 dBm, 5250–5350 MHz: 20 dBm, 5470–5725 MHz: 20 dBm, 5725–5850 MHz: 14 dBm

FCC Regulations

This tablet complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This tablet has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device causes harmful interference to radio or television reception, which can be determined by turning the device off and on, you can try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the device and the receiver.
• Connect the device to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for additional help.

Information on Exposure to Radiofrequency Energy (SAR)

This device meets government requirements for exposure to radio waves. The device is designed and manufactured not to exceed the emission limits for exposure to radiofrequency energy. The unit of measurement for the exposure standard for wireless devices is SAR (Specific Absorption Rate).

The SAR limit set by the FCC is 1.6 W/kg. The device has been tested and found to comply with the FCC radiofrequency energy exposure limits for body-worn use when used with a non-metallic accessory. SAR exposure limits have not been tested or certified with accessories containing metal, and the use of such accessories should be avoided.

FCC Notice

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Shielded cables must be used with this device to ensure compliance with FCC Class B limits.

Electronic Label

This device has an electronic label containing its certification information. You can access it by selecting Settings > About tablet > Certification or by selecting Settings and typing Certification in the search field.

Model: 24075RP89G (2407 indicates release after 202407).

Disclaimer

The publisher of this quick guide is Xiaomi or its local affiliate. Xiaomi may make improvements or changes to this guide at any time without notice due to typographical errors, inaccuracies in information, or improvements to programs and/or devices. Such changes will be incorporated into new online versions of this quick guide (for more information, visit www.mi.com/global/service/userguide). All illustrations are for reference only and may not fully represent the actual appearance of the device.

Manufacturer Information

Manufacturer: Xiaomi Communications Co., Ltd.

Manufacturer's address: #019, 9th Floor, Building 6, 33 Xi'erqi Middle Road, Haidian District, Beijing, China, 100085

Brand: Redmi Model: 24075RP89G

© Xiaomi Inc. All rights reserved.