Yaber YR800 Car Battery Jump Starter User Manual

Package Content

• 1 x Jump Starter
• 1 x Smart Jumper clamps
• 1 x Type C Cable
• 1 x User Manual
• 1x EC5 Cigarette Lighter Adapter
• 1 x Storage Case

Key Features

• Powerful Jump Starter: With 2500 amps peak current, it can jump-start 12V cars, SUVs, trucks, or vans (all gasoline and 8L diesel) in seconds, up to 30 times on a single charge.
• Efficient Charging: Equipped with two USB outputs (USB1: QC3.0 5V 3A / 9V 2A / 12V 1.5A, USB2: 5V 2.4A) and a 5V 2A Type C input for fast charging.
• Safety Protection: Premium cells, circuitry, and safety features protect you and your device from surges or short circuits.
• LED Lights & LCD Screen: Features a 3-mode LED light (flashlight, strobe, SOS) for emergency use and an extra red warning light. The LCD screen displays remaining power and output voltage.
• Convenient Wireless Charging: Offers 10W wireless charging, making it a convenient power bank on the go if you forget your charging cable.
• Car Safety Hammer: Includes a hardened sharp stainless steel point to shatter vehicle windows in an emergency.

Know Your Product

Jump Starter Components:

• 1. Jump starting port
• 2. Flashlight
• 3. QC 3.0 USB output
• 4. 5V/2.4A USB output
• 5. Type C input
• 6. LCD display
• 7. Power switch
• 8. Wireless charger
• 9. Compass
• 10. Safety hammer

Powerful Circuit Protection System - Smart Clamps:

• 1. Red jumper cable (+)
• 2. Black jumper cable (-)
• 3. "Smart Clamp" plug

Getting Started

Charging your Jump Starter:

1. Use a 5V/2A, 9V/2A, or 12V/1.5A adapter to charge the product. A Type C cable is included, but the adapter is not.
2. Using a 5V/2A adapter, it takes approximately 5-6 hours to fully charge the unit. To extend battery life, it is recommended to fully charge the unit every 3-6 months.

Turn On your Jump Starter:

Short press the power switch to boot the jump starter. The display will turn on. For energy saving, the jump starter will enter standby mode if there is no operation within 20 seconds.

LED Light:

Turn on the jump starter. Long press the power switch for more than 3 seconds to turn on the flashlight mode. There are four modes: illumination, SOS, and Strobe, plus a warning light. Short press the power switch to cycle through the three modes (illumination, SOS, Strobe) or turn off the flashlight. Double press the power switch to enter or exit the warning light mode.

QC3.0 & 5V 2.4A Dual USB Output:

This portable jump starter is equipped with two smart USB outputs for fast charging your portable electronic devices, such as phones, tablets, and Bluetooth earphones. USB1 supports QC3.0 (5V 3A / 9V 2A / 12V 1.5A), and USB2 supports 5V 2.4A.

Start your Car

1. Ensure the battery level is above 50% before jump-starting your car.
2. Insert the plug of the smart clamp completely into the jump starter. The green and red lights will flash alternately.
3. Correctly clip the red clamp to the positive (+) terminal and the black clamp to the negative (-) terminal of the car battery. The green light should stay on.
4. Start the vehicle.
5. Once the vehicle is started, immediately remove the jumper cables from the car battery.

Smart Clamp Protection Mode:

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.