IIWUS WS3000 AX3000 Gigabit Wi-Fi 6 Router Quick Installation Guide

Before You Begin

If your internet source is an Ethernet cable coming directly from the wall, connect it to the router's WAN port and skip steps 1, 2, and 3.

Setup Steps

1. Step 1: Power Off Modem

   Turn off the modem and remove the battery if it has one.

   Diagram Description: An illustration shows a modem with its power cord and battery compartment.

2. Step 2: Connect WAN Port

   Connect the router's WAN port to your DSL/Cable Modem/Ethernet source.

   Diagram Description: An illustration shows the back of the router with the WAN port highlighted and connected to a modem via an Ethernet cable.

3. Step 3: Power On Modem

   Turn on the modem and wait approximately 2 minutes for it to restart.

   Diagram Description: An illustration shows the modem powering on, with an indicator for waiting time.

4. Step 4: Connect Power Adapter

   Connect the power adapter to the router. Wait 1 minute for the system LED to change from flashing to solid (red or blue), indicating startup is complete.

   Diagram Description: An illustration shows the router being connected to its power adapter. An LED indicator on the router is shown.

5. Step 5: Connect Computer to Router

   Wired Connection: Turn off your computer's Wi-Fi and connect it to the router's LAN port using an Ethernet cable.

   Wireless Connection: Connect your device to the router's Wi-Fi using the SSID (network name) and Password printed on the bottom of the router.

   Example Wi-Fi Details:

   • 5GHz Wi-Fi: IIWUS-XXXX
   • 2.4GHz Wi-Fi: IIWUS-XXXX-5G
   • Password: XXXXXXXX

   Diagram Description: Two connection methods are shown: a computer connected via Ethernet cable to a LAN port, and a mobile device connecting wirelessly using the provided Wi-Fi credentials.

6. Step 6: Launch Web Browser

   Open a web browser and enter http://iiwus.net/ or http://192.168.10.1/ in the address bar. Create an administrator password to log in.

   Diagram Description: A screenshot shows the login page of the router's web interface, prompting for an administrator password.

7. Step 7: Follow Setup Instructions

   The following window will appear. Follow the step-by-step instructions to set up your internet connection.

   Diagram Description: A screenshot shows the quick setup wizard with options like Operation Mode (Wireless Router, Access Point, Extender, WISP, Client), Timezone, WAN, and Wireless settings.

8. Step 8: Enjoy the Internet!

   Your router is now set up and ready to use.

LED and Button Descriptions

Buttons:

• WPS Button: Press and hold for 1 second to enable the WPS function.
• Reset Button: Press and hold for 2 seconds to reset the router to its factory default settings.

Regulatory Information

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement: This device complies with FCC radiation exposure limits for an uncontrolled environment and Part 15 of the FCC RF Rules. It must be installed and operated according to instructions, with antennas providing at least 20 cm separation from all persons and not co-located with any other antenna or transmitter.

Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

The device meets the exemption from the routine evaluation limits of RSS 102 and compliance with RSS-102 RF exposure. Users can obtain Canadian information on RF exposure and compliance.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.