OWNER'S MANUAL
Model 655
55 GALLON SPRAYER
Document Code: 010-0655 Rev 6/22
Manufacturer: Harvest Tec, LLC.
Installation Instructions
Installation of Tank and Saddle
- Bolt the frame and legs to the forage harvester's tongue using 5/8" u-bolts. Check for wheel clearance and obstructions. Position the leg with the pump to face away from the opposite leg for easy plumbing access.
- Bolt the tank saddle into the legs using 1½" bolts.
- Place the tank in the saddle with the end fitting on the same end as the pump. Secure with 5/16"x3" bolts and double nuts.
- Thread the valve and filter into the side fitting of the tank. Run a line to the pump intake (follow arrows on pump).
- Wire the switch to a 12-volt power source on the tractor.
- Locate the band lubricator nozzle on the side of the blower housing. It must be placed before the feed intake and after the feed discharge. Cut an oblong hole (2½" long, 1¾" wide) on a straight radius line, 2" from the outside of the band. Align the two scored marks on the nozzle assembly with the radius line and weld in place. Ensure the spray tip aligns with the scored mark inside the nozzle housing and that inside and outside scores align.
- Run a line from the pump discharge to the nozzle assembly, securing with provided ties.
Diagram Description (Page 3): A diagram illustrates the placement of the nozzle assembly on a blower housing. It shows the discharge spout, nozzle assembly, feed inlet, and a radius line with measurements (2 inches). A note indicates the nozzle hole should point towards the outer diameter of the blower housing.
Installation of Inoculant Nozzle
- Mount the nozzle assembly above the cross auger by drilling a 9/16" hole in the side or top of the auger case. Connect the plumbing line from the pump discharge to the nozzle assembly. (Note: Quick connect fittings at both nozzles allow easy selection of spray point if sufficient slack is left.)
Operation Instructions
- The pump is an internal bypass type, operating continuously at 40 psi. For lubrication, it delivers 18 gallons per hour through lubricator tip #5003.
- For inoculant application, calculate your harvesting rate.
- Mix inoculant for desired application using the charts below.
Note: To apply product at 25 psi, order part #007-4121S.
General Application Chart
| Gallons/Hour at 40 psi | Tip Number 5002 | Tip Number 5003 | Tip Number 5004 | Tip Number 5005 |
|---|---|---|---|---|
| 12 | 18 | 24 | 30 |
| Gallons/Hour at 25 psi | Tip Number 5002 | Tip Number 5003 | Tip Number 5004 | Tip Number 5005 |
|---|---|---|---|---|
| 9.6 | 14.4 | 19.2 | 23.4 |
Recommended Tip for Water Lubrication at 40 PSI
| Load Size | Minutes to Load (5002 Tip) | Minutes to Load (5003 Tip) | Minutes to Load (5004 Tip) | Minutes to Load (5005 Tip) |
|---|---|---|---|---|
| 14 Ton | 35 | 23 | 17 | 14 |
| 12 Ton | 30 | 20 | 15 | 12 |
| 10 Ton | 25 | 16 | 12 | 10 |
| 8 Ton | 20 | 13 | 10 | 8 |
| 6 Ton | 15 | 10 | 7 | 6 |
| 4 Ton | 10 | 7 | 5 | 4 |
Maintenance
Clean the tip strainer and main strainer every ten hours of operation.
NOTE: Some inoculant products leave a residue after use. This residue may affect pumping performance. If a product residue is present, flush the system with clean water after each use.
Parts Breakdown
Diagram Description (Page 5): Two diagrams illustrate the parts breakdown. The first shows the tank assembly with its components. The second diagram displays various fittings, hoses, and the pump assembly, with numbered references corresponding to the parts list.
Tank Assembly Parts:
| Ref | Description | Part# | Qty |
|---|---|---|---|
| 1 | Tank | 005-9203 | 1 |
| 2 | Tank lid | 005-9022C | 1 |
| Tank lid gasket | 005-9022CG | 1 | |
| 3 | Tank straps | 001-4402 | 2 |
| 4 | Tank saddle | 001-4703 | 1 |
| 5 | Tank fitting | 005-9100 | 1 |
| 6 | Right saddle leg | 001-4703AR | 1 |
| 7 | Left saddle leg | 001-4703AL | 1 |
| 8 | Pump | 007-4120D | 1 |
| 9 | Elbow fitting | 003-EL3812 | 2 |
Component Parts:
| Ref | Description | Part# | Qty |
|---|---|---|---|
| 1 | Switch assembly | 030-4724 | 1 |
| 2 | Lube nozzle holder | 001-6501A | 1 |
| 3 | Brass nozzle cap | 004-4732 | 1 |
| 4 | Brass tip | 004-5003-BR | 1 |
| 5 | Tip check | 004-4468 | 1 |
| 6 | Brass nozzle body | 004-4731 | 1 |
| 7 | Nozzle lube insert | 001-6501B | 1 |
| 8 | Quick disconnect | 004-4710 | 1 |
| 9 | Elbow fitting | 003-EL1212 | 1 |
| 10 | Filter bowl assembly | 002-4315 | 1 |
| 11 | Nipple fitting | 003-M1212 | 1 |
| 12 | Ball valve | 002-2212 | 1 |
| 13 | Nipple fitting | 003-M3412 | 1 |
| 14 | 1/2" Hose | 002-9001 | 20ft |
| 15 | U-bolt | 001-4701B | 2 |
| 16 | Hose clamp | 003-9003 | 4 |
| 17 | Shut-off cap | 004-1207F | 1 |
| 18 | Nipple fitting | 003-M14 | 1 |
| 19 | Elbow fitting | 003-EL1412 | 1 |
| 20 | Female disconnect | 004-1207H | 1 |
| 21 | Quick connect | 004-1207G | 1 |
| 22 | Cap | 004-4723 | 1 |
| 23 | Swivel body | 004-4733 | 1 |
| 24 | Jiffy clip | 008-9010 | 2 |
| NP | Tip | 004-5002-BR | 1 |
| NP | Tip | 004-5004-BR | 1 |
| NP | Tip | 004-5005-BR | 1 |
| NP | Not Pictured |
Notes
Refer to specific sections for detailed notes.
Warranty Statement
Harvest Tec, LLC. will repair or replace components found to be defective within 12 months from the date of manufacture. This warranty does not cover components subjected to negligent use, misuse, alteration, accident, or repairs made with non-Harvest Tec parts. The obligation is limited to repairing or replacing defective parts returned to Harvest Tec, LLC. within 30 days of failure, with transportation charges prepaid by the customer.
This warranty does not cover injury or damages of any kind, direct, consequential, or contingent, to persons or property. It does not extend to loss of crop, losses from delays, or prospective profits. Recovery is limited to the cost of repair of defects.
There are no warranties, expressed or implied, of merchantability or fitness for a particular purpose.
Harvest Tec, LLC. cannot guarantee against conditions beyond its control affecting material availability or manufacturing. Harvest Tec, LLC. reserves the right to make design changes or specification changes at any time without obligation to purchasers of previously sold machines and parts.
Revised 6/22
