Warranty Policy | EGO POWER+
Home - beforeUdig
Home | Before You Dig Australia (BYDA)
Instruction Manual for EGO models including: EG0800E 56V Lithium Ion Cordless Earth Auger, EG0800E, 56V Lithium Ion Cordless Earth Auger, Ion Cordless Earth Auger, Cordless Earth Auger, Earth Auger, Auger
Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Safety Alert. Indicates a potential personal injury ...
File Info : application/pdf, 16 Pages, 1.54MB
DocumentDocumentEARTH AUGER
OPERATOR'S MANUAL
56V LITHIUM-ION
SAFETY WARNING - BEFORE YOU DIG:
Before using Earth Auger please ensure you check with relevant safe digging organisations in your region: Australia https://www.byda.com.au/ New Zealand https://www.beforeudig.co.nz/nz/home/
CORDLESS EARTH AUGER
MODEL NUMBER EG0800E
WARNING: To reduce the risk of injury, the user must read and understand the Operator's Manual before using this product. Save these instructions for future reference.
MNL_EGO_EG0800E_AV01.01_240326
A1
7. LED Indicator
1. Left Handle
6. Battery-Release Button
3. Rotation Direction/Speed Selector 2. Right Handle
8. Power Head
4. Lock-off Button
5. Variable-Speed Trigger Switch
9. Battery Pack Port
10. Socket Wrench (10 mm)
A2 13. Locking Pin
14. Pin Clip
12. Earth Auger Bit
11. Allen Key (5 mm)
B1 Right Handle Battery Pack Port Left Handle
Cable Base Slot
B2
C1
Bolt Washer
Nut
Cable Plug
1
2
Cable Socket
8 Sets of Screws, Washers & Nuts
Drive Shaft
Upper End of the Auger Bit
C2 1 2
D1
Rib Drive Shaft Locking Pin
Pin Clip
Mounting Slot
D2
Battery-Release Button 1
2
E
Lock-off Button
1 2
F
Rotation Direction/Speed Selector
R
2
1
G1 Right Handle
Left Handle
G2 Left Handle
G3 Right Handle
G4
90º
READ ALL INSTRUCTIONS!
READ OPERATOR'S MANUAL
WARNING: To ensure safety and reliability, all repairs should be performed by a qualified service technician.
SAFETY SYMBOL
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.
WARNING: Be sure to read and understand all safety instructions in this Operator's Manual, including all safety alert symbols such as "DANGER," "WARNING," and "CAUTION" before using this machine. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.
SYMBOL MEANING
SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, or CAUTION, may be used in conjunction with other symbols or pictographs.
SAFETY INSTRUCTIONS
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate.
Safety Alert
Indicates a potential personal injury hazard.
Read Operator's Manual Ear Protection
Eye Protection
Regulatory Compliance Mark
WEEE
Direct Current
To reduce the risk of injury, user must read operator's manual.
Always wear ear protection when operating this product.
Always wear safety goggles or safety glasses with side shields and a full face shield when operating this product.
This product complies with applicable Australian standards.
Waste electrical products should not be disposed of with household waste. Take to an authorized recycler.
Type or a characteristic of current
IPX4
Ingress Protection (IP) Rating
Protection from splashing water.
n 0
No Load Speed
Rotational speed, at no load
mm Millimeter Length or size
kg Kilogram Weight
°C
Degrees Celsius
Temperature
56 VOLT LITHIUM-ION CORDLESS EARTH AUGER EG0800E
5
GENERAL MACHINE SAFETY WARNINGS
WARNING: READ ALL SAFETY WARNINGS, INSTRUCTIONS, ILLUSTRATIONS AND SPECIFICATIONS PROVIDED WITH THIS MACHINE. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.
The term "machine" in the warnings refers to your mains-operated (corded) machine or battery-operated (cordless) machine.
PERSONAL SAFETY
Stay alert, watch what you are doing and use
common sense when operating a machine. Do not use a machine while you are tired or under the
influence of drugs, alcohol medication. A moment
of inattention while operating machines may result in
serious personal injury.
Use personal protective equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce
personal injuries.
Prevent unintentional starting. Ensure the switch
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
Do not operate machines in explosive atmospheres,
such as in the presence of flammable liquids, gases or dust. Machines create sparks which may ignite the dust or fumes.
Keep children and bystanders away while
operating a machine. Distractions can cause you to lose control.
ELECTRICAL SAFETY
Machine plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with earthed (grounded) machines. Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose machines to rain or wet conditions.
Water entering a machine will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the machine. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
When operating a machine outdoors, use an
extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
If operating a machine in a damp location is
unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying machines with your finger on the switch or energizing machines that have the switch on invites accidents.
Remove any adjusting key or wrench before
turning the machine on. A wrench or a key left attached to a rotating part of the machine may result in personal injury.
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the machine in unexpected situations.
Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
MACHINE USE AND CARE
Do not force the machine. Use the correct machine
for your application. The correct machine will do the job better and safer at the rate for which it was designed.
Do not use the machine if the switch does not turn
it on and off. Any machine that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from the machine before making any adjustments, changing accessories, or storing machines. Such preventive safety measures reduce the risk of starting the machine accidentally.
6
56 VOLT LITHIUM-ION CORDLESS EARTH AUGER EG0800E
Store idle machines out of the reach of children
Follow all charging instructions and do not charge
and do not allow persons unfamiliar with the
the battery pack or tool outside the temperature
machine or these instructions to operate the
machine. Machines are dangerous in the hands of untrained users.
Maintain machines and accessories. Check for
range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect
the machines operation. If damaged, have the
machine repaired before use. Many accidents are caused by poorly maintained machines.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
Use the machine, accessories and tool bits etc. in
SERVICE
Have your machine serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the machine is
maintained.
Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the machine for operations different from those intended could result in a hazardous situation.
Keep handles and grasping surface dry, clean
and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
Use machines only with specifically designated
battery packs listed below. Use of any other battery packs may create a risk of injury and fire.
When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Do not use a battery pack or tool that is damaged
or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire or temperature above 130 °C may cause explosion.
SAFETY WARNINGS FOR EARTH AUGER
Replace augers if cracked, bent, or damaged in any
way. Operating the machine with a damaged auger
can result in serious injury.
Never use the auger with the handles above waist
level. This restricts control of the auger and may
increase the risk of injury.
Hold the machine with both hands at the intended
handles. Loss of control can cause personal injury.
Hold the machine by insulated gripping surfaces,
when performing an operation where the digging
accessory may contact hidden wiring. Digging
accessory contacting a "live" wire may make exposed
metal parts of the machine"live" and could give the
operator an electric shock.
To reduce the risk of electrocution, never use the
auger near any buried electrical power cables.
Contact with or use near buried electrical power cables
may cause serious injury or electric shock resulting
in death.
Always start the machine at low speed and with
the auger bit tip in contact with the ground. At
higher speeds, the bit is likely to bend if allowed to
rotate freely without contacting the ground, resulting in
personal injury.
Apply pressure only in direct line with the bit
and do not apply excessive pressure. Bits can
bend causing breakage or loss of control, resulting in
personal injury.
Always be sure you have a firm footing. Be sure
no one is below when using the machine in high
locations.
Hold the machine firmly. Keep hands away from rotating parts. Do not leave the machine running. Operate the
machine only when hand-held.
56 VOLT LITHIUM-ION CORDLESS EARTH AUGER EG0800E
7
Do not touch the auger bit immediately after
operation. It may be extremely hot and could burn
your skin.
If something is wrong with the machine, such as
abnormal sounds, stop operating immediately and
contact your local service centre for repair.
To reduce the risk of explosion, never use the
auger near any buried gas lines, including water
lines and pipes. Contact with or use near buried water
or gas lines may result in bursting of water lines and
explosion from gas lines which may cause serious
injury or death.
Never operate at higher speed than the maximum
speed rating of the auger bit. At higher speeds, the
bit is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
Battery-operated machines do not have to be
plugged into an electrical outlet; therefore, they
are always in operating condition. Be aware of
possible hazards even when the machine is not
operating. Take care when performing maintenance
or service.
Do not wash with a hose; avoid getting water in
motor and electrical connections.
Frequently check and ensure that the locking
screw is secured in place.
The product can only be used for drilling holes, and
should not be used for other purposes.
Use only with the specified battery packs and
chargers listed below:
No-load Speed (n ) Forward 0 Reverse
Weight (Without battery pack)
Low: 0-150 /min High: 0-210 /min 100 /min 15.5 kg
Recommended Operating Temperature -20°C-40°C
Recommended Storage Temperature -40°C-70°C
PACKING LIST (FIG. A1 & A2)
RECOMMENDED ACCESSORIES
WARNING: Use only accessories listed below. Use of accessories that do not meet the original equipment specifications may lead to improper performance and compromised safety.
PART NAME 500mm Auger Bit Extension 100mm Earth Auger Bit 150mm Earth Auger Bit 200mm Earth Auger Bit 250mm Earth Auger Bit
MODEL NUMBER ABE2000 AET0400 AET0600 AET0800 AET1000
DESCRIPTION
KNOW YOUR POWER HEAD (Fig. A1) KNOW YOUR EARTH AUGER BIT (Fig. A2)
BATTERY
CHARGER
ASSEMBLY
BA1400, BA2800, BA4200, BA1400T, BA2800T, BA4200T, BA5600T, BA6720T
CH2100E, CH5500E, CH7000E
INSTALLING THE HANDLES
1. With the battery pack port facing backward, insert the tubes of the right and left handles into the curved slots on the power head base (Fig. B1).
Save these instructions. Refer to them frequently and use them to instruct others who may use this machine. If you lend someone this machine, lend them these instructions also to prevent misuse of the product and possible injury.
2. Align the two holes in each handle tube with the two holes in each base slot.
NOTE: I ncorrect right/left installation of the handles will prevent these holes from aligning.
SPECIFICATIONS
3. Use 8 sets of bolts, washers, and nuts to secure the handles to the power head. Use the wrench and 5 mm Allen key to tighten them securely (Fig. B2).
Voltage Torque Auger Bit/Hole Diameter
56V 74 Nm 200 mm
4. Align the arrow on the right handle cable with the arrow on the power head cable. Then insert the cable plug of the right handle into the cable socket of the power head. Tighten them securely (Fig. B2).
Maximum Drilling Depth
800 mm
NOTICE: To prevent cable damage do not bend or twist it during assembly.
8
56 VOLT LITHIUM-ION CORDLESS EARTH AUGER EG0800E
INSTALLING THE AUGER BIT
WARNING: The auger bit is very sharp. To prevent personal injury, exercise extreme caution when cleaning, installing, or removing the auger bit. Always wear protective gloves when performing maintenance on the auger bit.
1. Remove the locking pin with pin clip from the earth auger bit.
2. Mount the upper end of the auger bit onto the drive shaft of the power head (Fig. C1).
3. Align the connection holes on the auger bit and drive shaft.
4. Insert the locking pin through the aligned connection holes.
5. Close the pin clip to prevent the locking pin from falling out (Fig. C2).
SELECTING ROTATION DIRECTION AND SPEED (Fig. F)
Hold the right handle with your right hand.
Push the selector to the "2" position to activate
forward rotation at high speed.
Push the selector to the "1" position to activate
forward rotation at low speed.
Push the selector to the "R" position to activate reverse
rotation.
NOTE: Switching direction of rotation between forward and reverse is only possible when the auger is stopped.
NOTE: The forward speed adjustment could be achieved at any time, regardless if the auger is rotating or stopped.
OPERATION
APPLICATION You may use this product for the purposes listed below:
Drilling holes in soil
ATTACHING/DETACHING THE BATTERY PACK
Fully charge before first use.
To attach Align the battery ribs with the mounting slots and press the battery pack down until you hear a "click" (Fig. D1).
To detach Depress the battery-release button and pull the battery pack out (Fig. D2).
STARTING/STOPPING THE AUGER (Fig. E)
To turn the auger on, press and hold the lock-off
button and then squeeze variable-speed trigger switch. Release the lock-off button and continue to squeeze the trigger switch for continued operation.
NOTE: The variable-speed trigger switch delivers higher speed with increased trigger pressure and lower speed with decreased trigger pressure.
To turn the auger off, release the trigger switch and
allow the auger bit to come to a complete stop.
56 VOLT LITHIUM-ION CORDLESS EARTH AUGER EG0800E
9
STATUS INDICATOR
The power head of the auger features an LED status indicator to display the working status of the machine. The LED indicator will illuminate only when the auger is started.
LED Status Indicator Working Condition
Action
Solid green
The auger works properly.
Normal operation. No action needed.
Solid Red
The auger is overloaded.
Release the trigger, lift the auger from the hole and check for the causes of overload. You may need to find an alternative place to dig if a large obstruction has caused the machine to stop.
If the problem still can not be solved, contact EGO customer service for repair.
The auger is too cold.
Release the trigger. Bring the auger indoors to warm it up.
Solid Orange
Anti-kickback protection.
Release the trigger, lift the auger from the hole. Restart the auger and gently lower it back into the hole.
Flashing Red
The battery pack charge is nearly depleted.
Charge the battery pack.
Flashing orange
The auger is overheated.
Stop the auger and wait for some time to cool the auger.
Flashing green and red alternately.
Communication fault.
Contact EGO customer service for repair.
No light.
If the LED indicator on the battery pack flashes orange or shines red, the battery pack is overheated.
Allow the battery pack to cool down and restart the auger again.
Other electronics error.
Contact EGO customer service for repair.
10
56 VOLT LITHIUM-ION CORDLESS EARTH AUGER EG0800E
WORKING WITH THE EARTH AUGER
WARNING:
Contact local utility for underground service
marking before using machine to avoid contact with underground utilities
Do not use the auger for anything other than its
intended purpose.
Use the earth auger only for drilling holes in soil. Avoid digging in material that you suspect contains
hidden nails or other things that may cause the auger bit to bind or break.
Stay alert to the torque reaction force of the machine.
Always keep the operating position that you can withstand the torque reaction force.
Be extremely cautious when working on slopes or
uneven surface.
NOTICE: Before operating, check that there is no foreign matter (sand, dirt, etc.) stuck in the openings or moving parts.
a. Make sure feet are firmly planted above the work surface and stand with the handles close to waist. Firmly hold the right handle with your right hand and the left handle with your left hand (Fig. G1)
WARNING: Never hold the right handle with your left hand and the left handle with your right hand. Improper hand positions may result in serious injury (Fig. G2).
WARNING: Avoid improper positioning (Fig. G3). Do not stand too far from the machine. Proper reaction and control may not be achieved in the event of kickback.
b. Keep the auger bit away from your body and the auger bit pointing downward at a 90°angle to the surface.
c. Set the direction of rotation and rotation speed.
d. Lift the machine above the surface. Press and hold the lock-off button and squeeze the switch trigger.
WARNING: Do not touch the auger bit when the product is switched on.
e. Allow the auger to gain full speed.
f. Lower the auger bit into the surface maintaining the 90°angle (Fig. G4). Allow the auger bit to bite into the material, letting the machine do the work.
g. As the auger bit begins to fill with debris, it is important to constantly clear it to produce a clean cut and reduce the amount of effort required while the auger is operating at full speed, slowly lift it from the hole and allow the debris to clear from the auger bit.
h. After using this machine, release the trigger switch and allow the auger to come to a complete stop.
i. When leaving the machine, such as during a break, do not leave the machine inserted in the soil or lean it against a wall.
TIPS FOR USING THE EARTH AUGER
Pressing excessively on the machine will not speed
up the digging. Excessive pressure will only serve to damage the tip of the auger bit, decrease the machine performance, and shorten the service life of the machine.
When drilling a deep hole or drilling in clay soil, do not
try to dig at once. Dig the hole by lifting the machine up and down so that the loose soil in the hole can be discharged.
If the rotation speed of the machine slows down due to
high load operation, lift the machine up little, and move the machine up and down to drill in small steps.
A stuck auger bit can be removed simply by setting the
auger into reverse rotation in order to back out. When reversing, brace the machine by your body to prevent a clockwise reaction.
MAINTENANCE
WARNING: To prevent serious personal injury, remove the battery pack from the product before servicing, cleaning, changing attachments, or removing material from the unit.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use a clean cloth to remove dirt, dust, oil, grease, etc.
WARNING: Do not at any time allow brake fluids, gasoline, petroleum-based products, penetrating oils, etc. to come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.
Use a small brush or a vacuum cleaner with brush nozzle to clear dust or debris from the air vents in the power head.
STORING THE EARTH AUGER
1. Remove the battery pack from the auger.
2. Remove the auger bit from the drive shaft of the power head.
3. Clean the auger thoroughly before storing it.
4. Store the auger in a dry, well-ventilated area, lockedup or up high, out of the reach of children. Do not store the auger on or adjacent to fertilizers, gasoline, or other chemicals.
56 VOLT LITHIUM-ION CORDLESS EARTH AUGER EG0800E
11
Protecting the environment
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact your local government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain,damaging your health and well-being.
12
56 VOLT LITHIUM-ION CORDLESS EARTH AUGER EG0800E
TROUBLESHOOTING
PROBLEM
Machine fails to start or stops unexpectedly.
There is too much noise and/or vibration during operation.
Motor runs, but auger bit remains stationary.
The auger rotation direction or speed is not switched after pushing the rotation direction/ speed selector.
CAUSE
Low battery pack capacity Battery pack is overheated or
too cold.
The right handle cable is not
connected with the power head cable properly.
Some parts are loose.
Loose auger bit
Switching direction of rotation
between forward and reverse is only possible when the auger is stopped.
Other unidentified causes.
SOLUTION
Charge the battery pack. Wait for the battery pack to cool down or warm up,
at which point the auger can be started again.
Connect the cables of the right handle and the
power head following the step 4 in section "INSTALLING THE HANDLES" in this manual.
Stop the auger, remove the battery pack, check and
tighten loose parts.
Reinstall the auger bit following the section
"INSTALLING THE AUGER BIT" in this manual.
Stop the auger completely, push the rotation
direction/speed selector to desired rotation and then start the auger again.
Contact EGO service centre for repair.
56 VOLT LITHIUM-ION CORDLESS EARTH AUGER EG0800E
13
WARRANTY POLICY
For warranty service or to make a claim, please visit our Warranty Portal at egopowerplus.com.au/warranty-policy, alternatively you can contact EGO customer service via the following: Australia 1300 000 346, New Zealand 0508 000 346.
Chervon Australia Pty Ltd ABN 36 165 077 501 and Chervon New Zealand Subsidiary Ltd NZBN 9429049277616 ("Chervon") warrants to the original domestic purchaser that this product will be free from defects in materials and workmanship for 5 years from date of purchase, and any battery or charger will be free from defects in materials and workmanship for 3 years from date of purchase.
Warranty for commercial use is 1 year on all product, battery and chargers. The Commercial Range Product Warranty for commercial users is 2 years for commercial tools, commercial batteries and commercial chargers. Please refer to product warranty table below for further clarification.
The warranty period for routine accessories, consumables or maintenance parts, such as, but not limited to, ride-on mower seat, wheels, tyres, anti-scalp wheels, brake discs, blades, trimmer heads, chain bars, saw chains, augers, blower nozzles, and all other EGO accessories is 90 days for residential purpose, 30 days for industrial, professional or commercial purpose. These parts are covered for 90/30 days from manufacture defects in normal working conditions.
To make a claim, call 1300 000 346 for AU or 0508 000 346 for NZ or lodge a claim via our portal link above. Any handling and transportation costs (and other expenses incurred in claiming this warranty) are not covered by this warranty and will not be borne by Chervon. The replacement product or part or repaired product will be made available for your collection at an address nominated by Chervon. Where a valid warranty claim is made, Chervon will replace the defective product or repair the fault. Where the product is repaired, Chervon may use refurbished parts. This warranty does not cover normal wear and tear, misuse or abuse (including overloading of the product beyond capacity and exposure to water or rain), accidents, neglect or lack of proper installation, and improper maintenance or storage. This warranty does not cover the damage resulting from modification, alteration or unauthorised repair. This warranty does not cover normal deterioration of the exterior finish, including but not limited to scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive and chemical cleaners. This warranty is void if the product has been used for rental purpose. This warranty may also be further limited or voided as specifically detailed in the product Manual. Chervon has no other liability under this warranty. The benefits to you given by this warranty are in addition to other rights and remedies imposed by State and Federal legislation that cannot be excluded. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law and the New Zealand Consumer Guarantee Act 1993. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The warranty applies to the original purchaser and applies only to purchases made from authorised EGO Dealers, which can be confirmed on the website store locator. For avoidance of doubt, 3rd party online stores such as eBay, Gumtree, Amazon, etc. are excluded.
Chervon Australia Pty Ltd, Unit 14, 5 Kelletts Rd, Rowville, VIC. 3178. Ph Australia; 1300 000 346. Email: support@egopowerplus.com.au Chervon New Zealand Subsidiary Ltd, 4th Floor, Smith & Caughey Building, 253 Queen St, Auckland, 1141. Ph New Zealand; 0508 000 346. Email: support@egopowerplus.co.nz
14
56 VOLT LITHIUM-ION CORDLESS EARTH AUGER EG0800E
PRODUCT OR MODEL #
LIMITED WARRANTY FOR
LIMITED WARRANTY FOR
PROFESSIONAL USE (ANY
CONSUMER USE
COMMERCIAL, AGRICULTURAL,
(PERSONAL, HOUSEHOLD USE) INSTITUTIONAL,
OR INCOME-PRODUCING USE)
EGO Power+ Outdoor Power Equipment and Portable Power Products
5 years
1 year
EGO Power+ Battery Packs and Chargers
3 years
1 year
Specific warranties apply to the products below:
Commercial Tools*
5 years
2 years
Commercial Batteries & Chargers**
3 years
2 years
Mini Bike (MB1000E)
1 Year
N/A
Accessories / Consumables
90 Days
30 Days
*Commercial Tools include: BCX3800, BCX4500, BHX1001, CSX3000, CSX5000, EDX2000, HTX5300-P, HTX5300-PA, HTX7500, LBPX8000, LBX1000, LBX6000, LMX5300SP, PPX1000, PTX5100, PSX2500, PSX2510, STX3800, STX4500.
**Commercial Batteries & Chargers include: BAX1501, CHU6000E, CHX5500E, HC2240T, PGX1400PB, PGX1600E-H, PGX3000D.
56 VOLT LITHIUM-ION CORDLESS EARTH AUGER EG0800E
15