Coleman SaluSpa Owner's Manual

Important Safety Instructions

READ AND FOLLOW ALL INSTRUCTIONS.

WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.

A wire connector is provided on this unit to connect a minimum 8 AWG (8.37 mm²) solid copper conductor between this unit and any metal equipment, metal enclosures of electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit.

DANGER: Risk of injury.

• Replace damaged cord immediately.
• Do not bury cord.
• Connect to a grounded, grounding type receptacle only.

WARNING: This product is provided with a ground-fault circuit-interrupter (GFCI) integrated with the power plug. The GFCI must be tested before each use. With the product operating, push the test button on the GFCI; the product should not operate. Push the reset button; the product should now operate normally. If the product fails to operate in this manner, a ground current is flowing, indicating the possibility of an electrical shock. Disconnect the power until the fault has been identified and corrected.

DANGER: Risk of Accidental Drowning.

Extreme caution must be exercised to prevent unauthorized access by children. To avoid accidents, ensure that children cannot use this spa unless they are supervised at all times.

DANGER: Risk of Injury.

The suction fittings in this spa are sized to match the specific water flow created by the pump. Should the need arise to replace the suction fittings or the pump, ensure that the flow rates are compatible. Never operate the spa if the suction fittings are broken or missing. Never replace a suction fitting with one rated less than the flow rate marked on the original suction fitting.

DANGER: Risk of Electric Shock.

Install at least 5 feet (1.5 m) from all metal surfaces. Alternatively, a spa may be installed within 5 feet of metal surfaces if each metal surface is permanently connected by a minimum 8 AWG (8.37 mm²) solid copper conductor to the wire connector on the terminal box provided for this purpose.

DANGER: Risk of Electric Shock.

Do not permit any electric appliance, such as a light, telephone, radio, or television, within 5 feet (1.5 m) of a spa.

WARNING: To reduce the risk of injury:

• The water in a spa should never exceed 104°F (40°C). Water temperatures between 100°F (38°C) and 104°F (40°C) are considered safe for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes.
• Since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to 100°F (38°C).
• Before entering a spa, the user should measure the water temperature with an accurate thermometer, as the tolerance of water temperature-regulating devices varies.
• The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with the possibility of drowning.
• Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a physician before using a spa.
• Persons using medication should consult a physician before using a spa, as some medication may induce drowsiness while other medication may affect heart rate, blood pressure, and circulation.

WARNING: TO AVOID ELECTRIC SHOCK, DO NOT USE THE SPA WHEN IT IS RAINING.

WARNING: Water attracts children; Always attach a spa cover after each use.

WARNING: TO REDUCE THE RISK OF INJURY: Never add water that is higher than 104°F (40°C) into the Spa.

CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS.

CAUTION: The spa should not be setup or left out in temperatures lower than 40°F (4°C).

CAUTION: Do not use the spa alone.

CAUTION: Always enter and exit the spa slowly and cautiously. Wet surfaces are slippery.

CAUTION: To avoid damage to the pump, the spa must never be operated unless the spa is filled with water.

CAUTION: Immediately leave spa if the user feels uncomfortable or sleepy.

NOTE: Please examine equipment before use. Notify Bestway® at the customer service address listed on this manual for any damaged or missing parts at the time of purchase. Verify that the equipment components represent the model that you had intended to purchase.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

SAVE THESE INSTRUCTIONS

ASSEMBLY: THE PROVIDED WARNING LABEL

REDUCE THE RISK OF ELECTROCUTION

1. NEVER PLACE AN ELECTRIC APPLIANCE WITHIN 5 FEET OF SPA.

REDUCE THE RISK OF CHILD DROWNING

1. SUPERVISE CHILDREN AT ALL TIMES.

2. ATTACH SPA COVER AFTER EACH USE.

REDUCE THE RISK OF OVERHEATING

1. CHECK WITH A DOCTOR BEFORE USE IF PREGNANT, DIABETIC, IN POOR HEALTH, OR UNDER MEDICAL CARE.

2. EXIT IMMEDIATELY IF UNCOMFORTABLE, DIZZY, OR SLEEPY. SPA HEAT CAN CAUSE HYPERTHERMIA AND UNCONSCIOUSNESS.

3. SPA HEAT IN CONJUNCTION WITH ALCOHOL, DRUGS, OR MEDICATION CAN CAUSE UNCONSCIOUSNESS.

WHEN PREGNANT, SOAKING IN HOT WATER FOR LONG PERIODS CAN HARM YOUR FETUS. MEASURE WATER TEMPERATURE BEFORE ENTERING.

1. DO NOT ENTER SPA IF WATER IS HOTTER THAN 100°F (38°C)

2. DO NOT STAY IN SPA FOR LONGER THAN 10 MINUTES.

Installation Instructions

NOTE: The warning label must be posted near your spa in a readable position during using your spa.

1. Take out the warning label from the accessory kit.
2. Carefully peel the warning label.
3. Affix the warning label.

To order the warning label, please contact your local Coleman After Sales Service.

IMPORTANT !

To reach 104°F (40°C), the heating duration required is based on the starting water temperature and ambient temperature. The data below is purely for reference. To display the current water temperature, run the filter system for at least a minute.

Be sure to cover the spa with the spa cover whenever the heating function is activated. Leaving the spa uncovered will increase the heating duration required.

Please do not use the spa when ambient temperature is lower than 39°F (4°C).

Selected Location

IMPORTANT: Because of the combined weight of the SaluSpa, water, and users, it is extremely important that the base where the SaluSpa is installed is smooth, flat, level, and capable of uniformly supporting the weight for the entire time the SaluSpa is installed (not on the carpet or other similar material). If the SaluSpa is placed on a surface which does not meet these requirements, any damage caused by improper support is not covered under the manufacturer's warranty. It is the responsibility of the SaluSpa owner to assure the integrity of the site at all times.

Indoor Installation:

Be aware of special requirements if you install the spa indoors.

• Humidity is a natural side effect with SaluSpa installation. Determine the effects of moisture on exposed wood, paper, etc., in the proposed location. To minimize these effects, it is best to provide plenty of ventilation to the selected area. An architect can help determine if more ventilation is needed.

Outdoor Installation:

• During filling, draining, or when in use, water may spill out of the spa. Therefore, the SaluSpa should be installed near a floor drain.
• Do not leave the spa's surface exposed to direct sunlight for long periods of time.

GFCI Test

IMPORTANT: RISK OF ELECTRIC SHOCK. THE GFCI MUST BE TESTED BEFORE TURNING ON THE PUMP EACH TIME.

1. Plug the GFCI into a power outlet; the indicator turns red.
2. Press the test button; the indicator turns off.
3. Press the reset button; the indicator turns red, and the spa is ready for use.

WARNING: The GFCI plug must be tested before each use to avoid risk of electric shock.

WARNING: Before inserting the plug into a power outlet, make sure the current rate of the power outlet is suitable for the pump.

WARNING: Do not use the pump if this test fails and contact our Aftersales Service.

NOTE: When inflating, you will notice that air will be expelled from the area where the air hose connects to the pump; this is normal for technique requirements.

NOTE: Do not use an air compressor to inflate the pool.

NOTE: Do not drag the pool on rough ground as this may cause damage to the pool liner.

NOTE: Inflation time is for reference only.

NOTE: Pressure gauge is for inflation purpose only, and the value of the pressure gauge is just for reference; it should not be used as a precision instrument.

Air Valve Check

Always check the air valve carefully before inflation to ensure there is not an air leak. If the air valve is loose, use the provided wrench to fasten the air valve following these steps:

1. With one hand, hold the backside of the air valve from the inner side of the spa wall and turn the wrench clockwise.

NOTE: 1. Do not over tighten.

NOTE: 2. Do not adjust the air valve connector when the spa is in use.

Inflation Steps (Diagram Description)

The manual includes diagrams illustrating the inflation process. These steps involve connecting the pump to the spa liner, inflating to a specified pressure (0.08 Bar / 1.2 PSI) for approximately 5 minutes, and then inflating the outer cover for approximately 2 minutes. It also shows how to lock/unlock the pump and stop inflation.

• Step 1-2: Connect the pump to the spa liner and inflation hose.
• Step 3: Connect the inflation hose to the pump and inflate to 0.08 Bar (1.2 PSI) for 5 minutes.
• Step 4: Connect the inflation hose to the outer cover and inflate for 2 minutes.
• Step 5-9: Illustrate the pump's control panel, including lock/unlock functions, inflation status, and pressure gauge.

Specifications

NOTE: The above heating rate is based on a lab test conducted with an ambient temperature of 77°F (25°C) and above.

Parts List

Pump Operation & Control Panel

Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98.6°F (37°C). Symptoms include increased body temperature, dizziness, lethargy, drowsiness, and fainting. Effects include failure to perceive heat, failure to recognize the need to exit the spa, unawareness of impending hazard, fetal damage in pregnant women, physical inability to exit the spa, and unconsciousness leading to drowning.

WARNING – The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia.

WARNING: WATER TEMPERATURE IN EXCESS OF 100°F (38°C) CAN BE INJURIOUS TO YOUR HEALTH.

Control Panel Functions:

• A Lock/Unlock Button: The pump has a 5-minute auto-lock. To lock or unlock, place a finger over the button for 3 seconds.
• B Power-Saving Timer Button: Allows setting heating duration and activation time to save power.
• C Massage System Button: Activates the massage system with a 30-minute auto-shutoff. Do not run with the cover attached.
• D Celsius/Fahrenheit Toggle: Switches temperature display between Celsius and Fahrenheit.
• E Heat Button: Activates the heating system. The light is red when active, green when the set temperature is reached. Filtration system starts automatically.
• F Water Filter Button: Turns the filter pump on and off. The light is red when activated.
• G Temperature Adjustment Buttons: Increase or decrease the desired temperature. Holding the buttons rapidly changes the value.
• H Power-Saving Timer LED: Indicates heating duration setting (flashing) and timer activation (steady light).
• I LED Display: Shows the current water temperature. After 72 hours of filtration without timer use, the pump hibernates. Press Lock/Unlock for 3 seconds to re-activate.

NOTE: Water heat rate may change based on outdoor temperature (below 59°F/15°C) or if the cover is not in position during heating.

NOTE: To display current water temperature, run the filter system for at least 5 minutes. External thermometer readings may vary from the spa panel display.

Alarms

Maintenance

CAUTION: YOU MUST ENSURE THE PUMP IS UNPLUGGED BEFORE BEGINNING SPA MAINTENANCE TO AVOID RISK OF INJURY OR DEATH.

Filter Cartridge Maintenance

NOTE: To ensure your spa water stays clean, check and clean your filter cartridges every day.

The filter set (Part No. P6653) includes filter cartridges (Part No. 90352E).

NOTE: We recommend changing your filter cartridges every week or, if the filter cartridges remain soiled and discolored, they should be replaced.

Water Maintenance

Keeping your spa water clean and chemically balanced is necessary. Simply cleaning the filter cartridge is not enough for proper maintenance. Use pool chemicals to maintain water chemistry and chlorine or bromine tablets (not granules) with the chemical floater.

NOTE: We recommend you take a shower before using your SaluSpa, as cosmetic products, lotions, and other residues on the skin can quickly degrade water quality.

To use the chemical floater, follow these instructions:

• Using chemical tablets (not included).
• Using chemical liquid (not included).

NOTE: Remove the chemical floater from the spa when the spa is in use.

IMPORTANT: After performing chemical maintenance and before using the spa, use a test kit (not included) to test the water chemistry. We recommend maintaining your water as below:

NOTE: Damage resulting from chemical imbalance is not covered by the warranty. Pool chemicals are potentially toxic and should be handled with care. There are serious health risks from chemical vapors and the incorrect labeling and storage of chemical containers. Please consult your local pool supply retailer for more information about chemical maintenance. Pay close attention to the chemical manufacturer's instructions. Spa damage resulting from misuse of chemicals and mismanagement of spa water is not covered by the warranty.

Draining the Spa

NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.

The manual provides numbered diagrams for draining the spa. Key steps include:

1. Preparing the spa for draining.
2. Connecting a hose to the drain valve.
3. Opening the drain valve.
4. Allowing water to drain.
5. Lifting the spa when little water is left (damages to handles are not covered by warranty).
6. Drying the spa pool and pump.

Cleaning the Spa

Detergent residues and dissolved solids from bathing suits and chemicals may build up on the spa walls. Use soap and water to clean the walls and rinse thoroughly.

NOTE: DO NOT use hard brushes or abrasive cleaners.

Spa Repair

For inflatable cover:

If the spa is torn or punctured, use the provided heavy-duty repair patch.

1. Clean area to be repaired.
2. Carefully peel patch.
3. Press patch over area to be repaired.
4. Wait 30 seconds before inflation.

For Spa liner:

If the spa is torn or punctured, use the provided PVC repair patch and glue (not included) following these steps:

1. Clean and dry area to be repaired.
2. Cut the provided PVC patch to appropriate size.
3. Use glue (not included) to coat one side of the newly cut patch. Make sure the glue is evenly distributed.
4. Wait for 30 seconds and then place the cut patch with glue over the damaged area.
5. Smooth out any trapped air bubbles, and press firmly for two minutes.
6. The product is ready for use again. Repeat this process if further leaks occur.
7. Wait 30 minutes before inflation.

Spa Storage

Make sure the spa and pump are completely dry. This is essential to extend the life of the spa. It is recommended you store the spa in its original package in a warm dry place.

NOTE: Plastic becomes brittle and susceptible to breaking when exposed to subzero temperatures. Freezing can severely damage the spa. Improper winterization of your spa can void your warranty.

Troubleshooting

Coleman strives to provide the most trouble-free Spas on the market. If you experience any problems whatsoever, do not hesitate to contact Coleman or your authorized dealer. Here are some helpful tips to help you to diagnose and rectify some common sources of trouble.

Warranty

LIMITED 1 YEAR ON SPA PUMP WARRANTY

The product purchased comes with a limited warranty. Bestway® stands behind its quality guarantee and assures, through a replacement warranty, that your product will be free from manufacturer's defects. The limited warranty is valid as follows:

• 360 days for the heater pump from the original date of purchase.
• 180 days for the pool liner from the original date of purchase.
• 30 days for hoses, fittings, and accessories included in the package from the original date of purchase.

To enact a warranty claim, please contact your local Bestway® After Sales Center at 1-855-838-3888 before sending any documents. They will provide full instructions of what is needed for your claim. Bestway® is not responsible for economic loss due to water or chemical costs.

Bestway® will not replace any products deemed to have been neglected or used outside of the owner's manual guidelines. Bestway's warranty covers manufacturing defects discovered while unpacking the product or during use as recommended within the user manual. This warranty applies only to products which have not been modified by any 3rd parties. The product must be stored and handled in accordance with the technical recommendations.

The warranty does not cover damages caused by misuse, abuse, neglect, including, but not limited to collision, fire, use of incorrect voltage, excessive heat exposure, improper installation, improper wiring or testing, or improper storage. Replacements and repairs do not extend the duration of the warranty. The Limited Warranty is valid for the period indicated above. The warranty start date is the date of sale shown on the original receipt/purchase invoice.

The manual includes a section for choosing your spa and providing shipping information for warranty claims, including fields for Name, Address, City, State/Country, Zip Code, Retailer, Mobile, Telephone, E-mail, Spa Pump Batch Number, Spa Pool Batch Number, and Spa Pump Item Code. It also has a checklist for problem descriptions.

IMPORTANT: ONLY THE DAMAGED PART WILL BE REPLACED, NOT THE COMPLETE SET. Bestway® reserves the right to request photographic evidence of defective parts, or to require sending the item for additional testing. In order to better assist you, we request all information you provide to be complete.

For FAQ, Manuals, Videos, or Spare Parts, please visit the Bestway® website: www.bestwaycorp.com.