MotoMaster Booster Pack with Air Compressor

Safety Information

General Safety Instructions

This unit contains a maintenance-free, sealed lead acid battery. Although the unit arrives partially charged from the factory, it MUST BE FULLY CHARGED FOR 24 HOURS BEFORE FIRST USE. This initial charge pre-conditions the battery. Failure to follow this procedure may permanently damage the battery.

IMPORTANT

Abbreviations and Acronyms

• A: Amp (Ampere)
• V: Volts
• W: Watts
• DC: Direct current
• AC: Alternating current
• Ah: Amp-hours
• mA: Milli-Ampere
• cm: Centimetre
• LED: Light emitting diode

General Warnings

⚠️ WARNING The battery booster pack generates a high current of up to 900 peak Amps. Read and understand all safety information before using this product. Failure to follow these safety instructions may cause ELECTRIC SHOCK, EXPLOSION, or FIRE, which may result in SERIOUS INJURY, DEATH or PROPERTY DAMAGE.

• This product is only compatible with 12 V lead acid batteries. Do not attempt to use product with a 6 V or 24 V battery system.
• This unit is not intended to be used as a replacement vehicle battery. Do not attempt to operate a vehicle that does not have a battery installed.
• The cable clamps connecting the boosting cables to the vehicle’s battery terminals must be positive to positive ([+] red clamp) and negative to negative ([-] black clamp). A reverse polarity connection may cause damage to the unit and/or create a sparking hazard.
• Do not crank the engine for more than 5 seconds at a time. The jump start feature is designed for short term operation only. Operating the jump start feature for more than 5 seconds may cause damage to both unit and engine. Allow the battery booster pack to cool down for at least 3 minutes after each boost.
• Always turn the jump start system [OFF] when not in use.
• Do not charge the unit through the 12 V DC charging port if your vehicle’s electrical system operates above 15 V. This may lead to accumulation of hydrogen, causing exposure to fire and explosion hazards.
• Ensure that there are no 12 V DC appliances connected to the battery booster pack while the unit is being recharged.
• Do not use this unit to operate appliances that need more than 12 A to operate from the 12 V DC power port.
• Do not insert foreign objects into either the USB port or 12 V DC power port.
• This unit is not for use by children and should only be operated by adults.
• Store in a cool, dry place.

Risk of Electric Shock

⚡ RISK OF ELECTRIC SHOCK

• Do not expose product to rain, snow or use in damp conditions. Never submerge unit in water. Product is an electrical device that can produce shock and cause injury if used in wet environments.
• Do not operate the unit if it has received a sharp blow, been dropped or otherwise damaged in any way.
• Do not disassemble the unit; unit should only be serviced by a qualified technician. Refer to the warranty section of this manual for instructions on obtaining service. Attempting to service the unit yourself may result in a risk of electrical shock or fire and will void the warranty.

Explosion Hazard

? EXPLOSION HAZARD

• Do not operate unit near the presence of flammable/combustible liquids or gases.
• Never attempt to jump start a frozen battery.
• Never allow the red and black clamps to touch each other or a common piece of metal. The battery booster pack contains components that tend to produce arcs or sparks.
• Batteries generate hydrogen gas during normal operation which can be ignited by sparks from electrical connections. To prevent the risk of fire or an explosion, always operate in a well-ventilated area and follow all safety information instructions.
• Always ensure someone is nearby to help you in an emergency.

Risk of Injury

? RISK OF INJURY

• Always wear eye protection when working with batteries. Batteries can explode and cause flying debris.
• If battery acid comes into contact with eyes, flush affected area with running water immediately for at least 15 minutes and seek medical attention immediately.
• If battery acid comes into contact with skin, rinse immediately with water and wash thoroughly with soap and water. If redness, pain or irritation occurs, seek medical attention immediately.
• Be sure to remove all metal items (watches, necklaces, rings, etc.) before using the jump start system.

Key Parts List

The unit features several key components for its operation. A diagram illustrates these parts, numbered for reference:

• 1: Boosting Power Switch
• 2: 12V DC Power Port
• 3: DC Charging Port
• 4: Charging Status LEDs (2)
• 5: Battery Level Indicator
• 6: Battery Status Button
• 7: Air Compressor Power Switch
• 8: Air Compressor Gauge
• 9: Positive (+) Red Clamp
• 10: Negative (-) Black Clamp
• 11: Reverse Polarity Warning LED
• 12: USB port
• 13: LED light
• 14: LED light switch
• 15: Air Compressor Nozzle Connector
• 16: 120 V AC Charging Port
• 17: Ball/Balloon Adaptors
• 18: Fuse
• 19: 12V DC Charging Adaptor
• 20: Extension cord

Recharging

CAUTION! EQUIPMENT DAMAGE Do not charge the unit through the 12V DC charging port if your vehicle's electrical system operates above 15 V. Ensure that no 12 V DC appliances are connected while recharging. Do not operate any unit functions while charging. Do not recharge while connected to an external battery.

Battery Status

Press and hold the Battery Status Button. The Battery Level Indicator LEDs will illuminate to indicate the battery capacity level:

• Fully charged battery
• 75% charged battery
• 50% charged battery
• 25% charged battery

IMPORTANT Recharge battery as soon as possible after each use or every two months when in storage to prolong battery life and keep the unit ready for use. Allowing the unit to stay in a discharged state can cause battery failure. It is recommended to recharge unit every two months when not in use. All lead acid batteries suffer from self-discharge over time, especially under extreme temperatures. Store in a cool dry place.

NOTE The red CHARGING STATUS LED light indicates charging. The battery status indicator illuminates green when fully charged. Charging current automatically goes to floating charge.

Recharging with standard household extension cord (included)

1. Turn BOOSTING switch to the [OFF] position.
2. Pull open the AC adaptor cover on the side of the unit.
3. Connect the female end of the extension cord (included) to the AC plug.
4. Connect the male end of the extension cord to a grounded 120 V AC outlet.

Charging with 12V DC Charging Adaptor

NOTE Due to a safety circuit built into the input charging port, DC charging through this location will not fully charge the battery. The vehicle should be running for full charging to take place (DC charging will not work if the engine is off).

1. Turn BOOSTING switch to the [OFF] position.
2. Plug the 12V DC Charging adaptor pin into the DC charging port.
3. Plug the 12V DC Charging plug into the vehicle’s 12V DC accessory outlet.

A red light on the DC adaptor outlet will illuminate to confirm a good connection.

Operation

Jump Starting

⚠️ WARNING! EQUIPMENT DAMAGE Do not crank the engine for more than 5 seconds at a time. Allow the battery booster pack to cool down for at least 3 minutes after each boost.

⚠️ WARNINGS! EXPLOSION HAZARD Do not turn jump start switch to [ON] position if the REVERSE POLARITY WARNING LED light is ON and an alarm buzzer is sounding. Never allow the red and black clamps to touch each other or a common piece of metal.

Important Pre-operation Checks

• Turn off vehicle ignition and all accessories; ensure vehicle is in "park" and emergency brake is engaged.
• Make sure the BOOSTING POWER SWITCH is in the [OFF] position.
• Do not attempt to jump start an engine if the battery level is at 50% or less.
• Do not place the unit where it could fall when the vehicle starts up.
• Make sure that cables are routed away from the motor fan or belts.

Jump Starting Procedure

Note: Instructions are for negative ground systems only (most common for vehicles today). If your vehicle is a positive ground system, reverse steps 1 and 2. Please consult your vehicle’s manual to confirm your vehicle’s ground system.

NOTE: If the red REVERSE POLARITY WARNING LED light is on and an alarm is activated, STOP and reverse clamp connections immediately.

1. Connect the red clamp to the POSitive ([+]) terminal of the vehicle battery.
2. Connect the black clamp to the NEGative ([-]) terminal of the vehicle battery.
3. When clamps are connected properly, turn BOOSTING switch to the [ON] position.
4. Try starting your vehicle. Crank the engine in 5 second bursts until the engine starts.
5. Once the vehicle starts, turn BOOSTING switch to the [OFF] position.
6. Disconnect both clamps in the reverse order (black clamp first, then red clamp).
7. Recharge unit immediately and store unit safely.

12V DC Accessory Power

This unit is equipped with one DC outlet socket and can be used to power most 12 volt accessories and appliances. The running time will depend on the condition of the battery and the current draw of the appliance.

1. Pull open the cover of the 12 V DC Power Port on the side of the unit.
2. Insert the 12 V DC plug from the appliance into the 12 V DC Power port on the unit.
3. Switch appliance ON and operate as usual.

Typical Operating Times

*Actual wattage of different models may vary.
**Approximate running time for reference only based on fully charged battery and model used. Actual running time may vary based on model load and battery condition.

IMPORTANT Do not use this unit to operate appliances that need more than 12 A to operate from the 12 V DC power port. The unit has a 12 Amp automatic overload protection. If loaded more than 12 Amp, it will auto shut off for protection.

Operate Air Compressor

This unit is equipped with a built-in 150 PSI air compressor that can be used to inflate tires, sports equipment, and other recreational inflatables.

CAUTION! EQUIPMENT DAMAGE Do not operate air compressor continuously for longer than 10 minutes. Allow compressor to cool down for every 10 minutes of continuous use.

CAUTION! BURST HAZARD AND INJURY Carefully follow instructions and recommended pressure of products being inflated. Do not over-inflate. Always wear eye protection. Always check pressure with the pressure gauge. Never leave the compressor unattended during use.

IMPORTANT The Air Compressor operates from the internal battery of the unit. Check battery condition to make sure it is satisfactory before operating compressor. Do not use compressor function if battery is less than 50%. Recharge unit after each use.

1. Remove hose from storage compartment.
2. a) For inflating tires or other objects with valve stems, screw in the nozzle connector to the valve stem.
3. b) For inflating sporting equipment, party balloons or other objects without valve stems, screw in the appropriate adaptor into the nozzle connector and insert it into the object being inflated.
4. Turn Compressor switch to the [I] position.
5. Monitor the pressure gauge while inflating. When desired pressure is reached, turn compressor switch to [O] position.
6. Unscrew the nozzle connector from the valve stem of the object being inflated. If using an adaptor, disconnect from object being inflated and remove adaptor from nozzle connector.
7. Store air hose and ball/balloon adaptors in the appropriate storage compartments.

LED Light

Press the LED Light switch to turn the LED light ON/OFF.

IMPORTANT Make sure the LED light is [OFF] when the unit is being recharged or stored.

USB Port

The unit is equipped with a USB port with a 5V 2.4A power output. This port is ideal for charging portable electronic devices such as smartphones, tablets, and more.

Connect your device to the USB Power port and operate your device normally.

IMPORTANT Make sure there are no devices plugged in to the USB power port when the unit is being recharged or stored.

Fuse Replacement

The fuse in the plug end of the 12 V DC charger protects the adaptor's charging circuit. If the 120 V AC charger works but DC charging does not, the fuse may have blown. This product comes with a replacement fuse for the 12 V DC adaptor.

To replace the fuse in the plug:

1. Twist off the upper cover.
2. Check fuse condition. If blown, remove the blown fuse and insert the replacement 2 A fuse.
3. Twist the upper cover back on the plug. Do not over tighten the cover.

The 12V DC plug contains a 2 A 250 V Fuse. The upper cover should be handled carefully.

Maintenance

Routine maintenance is required to keep your MotoMaster® battery booster pack operating properly.

CAUTION! EQUIPMENT DAMAGE All batteries lose energy from self-discharge with time, more rapidly at higher temperatures. Gradually warm the frozen battery to 0°C (32°F) before recharging to avoid battery damage.

• Occasionally clean the outer surfaces with a soft cloth moistened with a mild solution of water and detergent. Do not use solvents or other chemical cleaners.
• Periodically inspect the condition of charging adaptors, connectors, and wires. Contact the manufacturer to replace any components that may have become worn or broken.
• Do not open or disassemble. Service on this unit is confined to replaceable parts only. All other servicing should be performed by a qualified person.
• We recommend charging the battery through the built-in AC charger after each use or at least every 2 months to maintain maximum battery capacity. Failing to do so may result in permanent battery damage and poor performance.

WARNING! SHOCK AND FIRE HAZARD Disconnect all sources of AC power and DC power before performing any type of maintenance.

Troubleshooting

Note: If the above solutions do not eliminate the problem, contact MotoMaster Customer Service at 1-888-942-6686 for assistance.

Technical Specifications

Environmental Protection

Battery Recycling

The jump starter is designed to provide years of service. However, the internal battery is not designed to be user replaceable. Because the internal batteries contain lead, which can be hazardous if exposed to the environment, the battery should be recycled or safely disposed of at your local recycling depot. Do not dispose of the battery and the jump starter with common household waste. Please ask your local authorities about recycling services that are available in your area.

Disposal

Do not dispose of this product in household garbage at the end of its life cycle; hand it over at a collection point for the recycling of electrical and electronic appliances. The symbols on the product, the instructions for use or the packing will inform about the methods for disposal.

Warranty

This MotoMaster® product carries a one (1) year limited warranty against defects in workmanship and materials. At its discretion, MotoMaster® Canada agrees to have any defective part(s) repaired or replaced free of charge, within the stated warranty period, when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse.

Made in China. Imported by MotoMaster Canada Toronto, Canada M4S 2B8.