LIVALL S2 & H2 Phone Holder

After-Sales Service

Warranty Card

Thank you for purchasing a LIVALL product. Please read the following instructions for better service.

1. This product can be replaced within three months after the date of purchase and comes with a one-year warranty.
2. Damages caused by the following reasons are not included in the scope of free warranty:
   • Exceeding the specified warranty period.
   • Damages caused by failure to follow the operating instructions.
   • Damages caused by unauthorized disassembly or maintenance by users or other man-made damages.
3. This warranty card is the important certificate for the warranty service provided to the end user. Please keep it well. The card should be taken along with the product to the manufacturer when maintenance is required.
4. LIVALL reserves the rights to modification and explanation for the above terms and conditions.
5. For more information, please visit www.livall.com.

Warranty Information:

User Name: _______________________

Tel.: _____________________________

ID No.: ___________________________

Home Address:_____________________

Seller: __________________________

Purchase Date:_____________________

Maintenance Record: ________________

Note: This form should be completed with real details; otherwise, it would be invalid.

Product Instruction of LIVALL Phone Holder

Thank you for choosing LIVALL phone holder. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for further reference.

Installation

I. Install S2

Remove the original stem and replace it with the LIVALL S2 holder.

Steps:

1. Remove the original stem: Unscrew and take off the original stem.
2. Install S2: Mount the LIVALL S2 holder onto the front fork.
3. Secure: Install the four screws on the stem cover.

II. Install H2

Remove the two screws on the top of the original stem and install the LIVALL H2 phone holder.

Steps:

1. Remove original stem screws.
2. Install H2 holder onto the stem.

Adjust the Angle of the Phone

To Stabilize Phone:

1. Loosen clips: Rotate the knob clockwise to loosen the clips.
2. Insert phone: Pull the top clip upwards, place your mobile phone, and release the top clip to stabilize your phone.
3. Secure phone: Rotate the knob counterclockwise to fix your phone properly.

Charging and Power Management

IV. Charge the Phone with S2

Connect the device to be charged to the USB output port using a USB cable. During discharging, the remaining power is displayed.

V. Charge S2

Use a Micro USB cable to connect the Micro USB port to a USB charger with safety approvals (e.g., CCC or UL). The charging power is displayed during charging.

VI. Check S2 Power

Press the power button to check the remaining power, which is displayed by the battery indicator icon (four levels).

Product Specifications

General:

• Applicable phone size: 4-6 inches
• Phone holder rotating angle: 360°
• Phone holder vertical turning angle: >200°

Bikes Applicable to H2:

• Requires M5 screws on the stem.
• Distance between two screws: 14-34 mm.

Parameters Applicable to S2:

• Bikes applicable to S2: diameter of the central handlebar: 31.8 mm; diameter of front fork stem: 28.6 mm.

S2 Power Bank Specifications:

• Battery capacity: 3.7V/5000mAH
• Charging port: Micro USB 5V/1A
• Charging duration: around 7 hours
• Output port: USB A, 5V/2A output
• Button: Power checking
• Lighting indicator: Four-level power indication
• Stem length: 120mm
• Product size: 180*116*125mm

Precautions

1. If the product is being used for the first time or if it has not been used for a prolonged period, the battery may self-discharge slowly. It generally takes five to six full charge and discharge cycles for the battery to maximize its performance.
2. Use a charger with safety approvals such as CCC or UL to charge this product.
3. Rough handling can cause damage to the internal precision parts and structure of the product.
4. Properly store this product and relevant accessories and place them out of reach of children.
5. It is normal for the product to get warmer during charging.
6. Keep the product away from fire or other heat sources to avoid danger.
7. Avoid contact with metal objects to the charging port or discharge port; otherwise, short circuit may occur and cause damage to the product.
8. Changes or unauthorized repair of the product could cause it to fail in normal use and void the warranty.

Additional Information

Download the LIVALL app and find more information at www.livall.com.

Product Identification: LIVALL S2, LIVALL H2 Phone Holder

Designed and Assembled in Shenzhen, China.