Installation Guide for DMP models including: 1107, Micro Window Transmitter
The 1107 Micro Window Transmitter is a low‑profile 1100 Series transmitter that can be used on windows. It is powered by a 3 V coin cell battery and contains a.
File Info : application/pdf, 4 Pages, 440.81KB
DocumentDocument1107 MICRO WINDOW TRANSMITTER Installation Guide Figure 1: 1107 Micro Window Transmitter DESCRIPTION The 1107 Micro Window Transmitter is a lowprofile 1100 Series transmitter that can be used on windows. It is powered by a 3 V coin cell battery and contains a single reed switch. Compatibility All DMP XT Series and XR Series and 1100 Series Wireless Receivers What is Included? · 1107 Transmitter PCB Mounted in a TwoPart Housing · One Magnet with a Standard and a Commercial Housing · One CR2430 3 V Coin Cell Lithium Battery · Doublesided Tape 1 PROGRAM THE PANEL When programming the 1107 in the panel, refer to the panel programming guide as needed. 1. In ZONE INFORMATION, enter the wireless ZONE NO: and press CMD. 2. Enter the ZONE NAME and press CMD. 3. Select NT (Night) as the ZONE TYPE. 4. Select the AREA. 5. At the NEXT ZONE prompt, select NO. 6. Select YES when WIRELESS? displays. 7. Enter the eightdigit SERIAL# and press CMD. See Figure 2 for the serial number location. 8. Enter the SUPRVSN TIME and press CMD. 9. At the NEXT ZONE prompt, select YES if you are finished programming the zone. Select NO if you would like to access additional programing options. 2 INSTALL THE BATTERY After the transmitter has been programmed into the panel, install the battery. Use a 3 V lithium battery, Sony CR2430, or equivalent battery from a local retail outlet. Keep in mind, when setting up a wireless system, program zones and connect the receiver before installing batteries in the transmitter. 1. Insert a small screwdriver into each notch in the housing cover and lift until the cover comes off. Do not twist the screwdriver. 2. Observing polarity, place the battery in the holder with the positive (+) side up. Press it into place. See Figure 2 for the battery location. Survey LED Serial Number Battery Location Internal Reed Switch Figure 2: Battery Location and PCB Features 3 SELECT A LOCATION The 1107 provides a survey capability to allow one person to confirm communication with the wireless receiver or panel while the cover is removed. 1. Hold the 1107 transmitter and the included magnet in the exact desired location. 2. Move the magnet away from the transmitter to send data to the receiver and determine if communication is confirmed or faulty. See Figure 2 for LED locations. Confirmed: If communication is confirmed, for each transmission the LED blinks immediately on and immediately off. Repeat this test to confirm five separate consecutive LED blinks. Any indication otherwise means proper communication has not been established. Faulty: If communication is faulty, the LED remains on for about 8 seconds or flashes multiple times in quick succession. Relocate the 1107 or wireless receiver until the LED confirms clear communication. 4 3. Relocate the 1107 or receiver until the LED confirms clear communication. Proper communication between the 1107 and receiver is verified when the LED blinks immediately on and immediately off each time the magnet is removed. MOUNT THE 1107 TRANSMITTER The transmitter and magnet assembly should have no more than 1/2" between the assembled housings after installation. When mounting on metal (ferrous) surfaces, this distance is slightly less. DMP recommends mounting the transmitter on the window frame and the magnet assembly on the window. Pan-Head Securing Screw (optional) 1. Hold the transmitter base in place with the reed switch alignment marker near where the magnet assembly will be mounted. See How to Align the Transmitter and Magnet Assembly for more information. Note: Do not remove the PCB from the housing during installation. 2. Place the two supplied #4 flathead screws into the mounting holes to secure the housing base to the surface. See Figure 3. 3. Replace the cover. For environments where the cover could be dislodged, use the optional #4 panhead securing screw instead of the center flathead screw to secure the transmitter and cover to the mounting surface. See Figure 3. Flat-Head Mounting Screws Figure 3: Mounting Hole Locations For even quicker installations, use the included doublesided tape instead of the screws to attach the housing to the mounting surface. HOW TO ALIGN THE TRANSMITTER AND MAGNET ASSEMBLY When you mount the transmitter and magnet assembly, use the alignment markers to ensure that the transmitter's internal reed switch is lined up with the magnet. There should be no more than a 1/2" inch of space between the transmitter and the magnet assembly. Alignment Markers 1/2" Max Distance 2 1107 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 5 MOUNT THE MAGNET ASSEMBLY Only one magnet assembly is required for internal reed switch operation. Depending on the installation requirements, you Magnet Cover can use either the standard or commercial magnet assembly. Standard Magnet Assembly 1. Place the magnet assembly base on the surface nearest the transmitter's internal reed switch location. Be sure to align the markers on the transmitter and magnet assembly. 2. Use the provided #4 flathead screws or included doublesided tape to secure the base in place. Base Figure 4: Standard Magnet Assembly 3. Snap the magnet into the magnet assembly cover, then snap the cover onto the base. Commercial Magnet Assembly 1. Snap the magnet into the magnet assembly cover. Cover 2. Place the cover on the surface nearest to the internal reed switch location. Be sure to align the markers on the transmitter and magnet assembly. Magnet 3. Use the supplied #4 flathead screws to mount the magnet assembly. See Figure 5. Figure 5: Commercial Magnet Assembly 6 TEST THE 1107 After installing the 1107, perform a Wireless Checkin Test to confirm the 1107 is communicating with the panel. At the keypad, enter 8144 (WALK) and select WLS. If the 1107 fails to check in at the keypad, relocate the wireless device, receiver, or panel. REPLACE THE BATTERY 1. Insert a small screwdriver into the notch in the housing cover and lift until the cover comes off. Do not twist the screwdriver. 2. Remove the old battery and dispose of it properly. 3. Observing polarity, place the new battery in the holder and press into place. 4. Snap the transmitter housing cover back on the base. Caution: Properly dispose of used batteries. Do not recharge, disassemble, heat above 212°F (100°C), or incinerate. Risk of fire, explosion, and burns. Sensor Reset to Clear LOBAT When the battery needs to be replaced, a LOBAT message will display on the keypad. Once the battery is replaced, a sensor reset is required at the system keypad to clear the LOBAT message. 1. On a Thinline keypad, press and hold "2" for two seconds. On a touchscreen keypad press RESET. 2. Enter your user code if required. 3. The keypad displays SENSORS OFF followed by SENSORS ON. 1107 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3 FCC INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from all persons. It must not be located or operated in conjunction with any other antenna or transmitter. Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. Industry Canada Information This device complies with Industry Canada Licenceexempt RSS standard(s). Subject to the following two conditions: 1. This device may not cause interference, and 2. this device must accept any interference, including interference that may cause undesired operation of the device. This system has been evaluated for RF Exposure per RSS102 and is in compliance with the limits specified by Health Canada Safety Code 6. The system must be installed at a minimum separation distance from the antenna to a general bystander of 7.87 inches (20 cm) to maintain compliance with the General Population limits. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. L'exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux limites établies par le Code de sécurité 6 de Santé Canada. Le système doit être installé à une distance minimale de 7.87 pouces (20 cm) séparant l'antenne d'une personne présente en conformité avec les limites permises d'exposition du grand public. 1107 MICRO WINDOW TRANSMITTER Specifications Battery Life Expectancy Type Frequency Range Dimensions Transmitter Standard Mag. Commercial Mag. Color Housing Material 2 years 3 V Lithium CR2430 905927 MHz 2.625" L x 1" W x .3125" H 2.125" L x .375" W x .3125" H 2.125" L x .375" W x .3125" H White Flame retardant ABS Patents U. S. Patent No. 7,239,236 Certifications FCC Part 15 Registration ID CCKPC0133 IC Registration ID 5251APC0133 Designed, engineered, and manufactured in Springfield, MO using U.S. and global components. LT-1156 21203 INTRUSION · FIRE · ACCESS · NETWORKS 2500 North Partnership Boulevard Springfield, Missouri 658038877 800.641.4282 | DMP.comAdobe PDF Library 15.0 Adobe InDesign 16.2 (Windows)