Day-Brite CFI Motion Sensor Remote Control
This document provides instructions for the Day-Brite CFI Motion Sensor Remote Control, designed for LED High Bay lights.
Product Information
| 12NC | Description | Power | Upload Range | Op. Temperature |
| 911401855781 | HCY-REMOTE control | 0.1W | Up to 15m(50ft.) | 0℃~50℃ |
Dimensions
140.4mm (Length) x 50.4mm (Width) x 17.6mm (Depth)
Power Supply
2x AAA 1.5V batteries, alkaline preferred.
Sensor Configuration
- Press the OFF button to display the latest configurations.
- Press the "BRIGHTNESS", "HOLD TIME", "STANDBY DIM", "STANDBY TIME", "SENSITIVITY", "DAYLIGHT" buttons to select new parameters.
- Aim the remote at the luminaire and press the SEND button to upload new parameters. The luminaire will flicker ON and OFF once as confirmation.
ON/OFF Switch Mode (Sensor Disabled)
- Long press the OFF button for 3-5 seconds until the brightness indicator light turns on.
- In ON/OFF switch mode, press buttons to select new parameters.
- Aim the remote at the luminaire and press the SEND button to upload new parameters. The luminaire will flicker ON and OFF once as confirmation.
- Aim the remote at the luminaire and press the ON/OFF button to turn the fixture off or on.
- Aim the remote at the luminaire and long press the OFF button for 3-5 seconds to exit ON/OFF switch mode. The luminaire will flicker ON and OFF once as confirmation.
Notes:
- Press any button to light up the remote indicator, then press the SEND button. The luminaire will flicker ON and OFF once as confirmation. The remote indicator will turn off automatically after 10 seconds of inactivity.
- In ON/OFF Switch Mode, only the "ON/OFF", "BRIGHTNESS", and "SEND" buttons are active. Long press the "ON/OFF" button for 3-5 seconds to exit this mode and return to sensor sensing mode.
- In TEST Sensitivity Mode, only the "TEST", "SENSITIVITY", and "SEND" buttons are active. Press the "TEST" button again to exit this mode.
- The HB03R IR Remote cannot pass through walls or other opaque materials. Ensure no objects block the path between the remote and the sensor.
- The HB03R is not waterproof. Avoid prolonged placement in damp environments.
Button Operation
| Button | Description | Button | Description | Button | Description |
|---|---|---|---|---|---|
| ON/OFF | Long press for 3-5 seconds until the brightness indicator lights up. Then press the button to set the light to permanent ON or permanent OFF mode, disabling the sensor. (Must long press OFF button to quit ON/OFF switch mode for setting.) | BRIGHTNESS | Press the button to adjust brightness level: 70%/80%/90%/100%. Short press or long press the button to adjust the lamp brightness in the range of 0%-100%. Note: After power-off, the brightness returns to the last set percentage. | SEND | Every change requires pressing the SEND button to upload current parameters to the sensor(s). The connected LED light will flicker ON and OFF as confirmation. Note: When the indicator light is on, the program can only be sent after the SEND button is pressed. |
| HOLD TIME | Press the button to adjust hold time: 10s/1min/10min/30min. | STANDBY DIM | Press the button to adjust standby dimming level: 10%/20%/30%/50%. | STANDBY TIME | Press the button to adjust standby time: 1min/30min/60min/+∞. |
| SENSITIVITY | Press the button to adjust occupancy sensing sensitivity: 20%/50%/75%/100%. | DAYLIGHT | Long press the button for 3-5 seconds until the 10 30 50 100 indicator lights up, then press the button to adjust daylight lux: 10lx/30lx/50lx/100lx. Short press or long press the button to adjust the lamp brightness in the range of 100%-0%. Note: After power-off, the brightness returns to the last set percentage. | RESET | Press the button to restore the remote control to its default settings: brightness 70%, hold time 10s, standby dim 10%, standby time +∞, sensitivity 20%, daylight off. |
| TEST | The TEST button is for testing sensitivity only. After selecting sensitivity thresholds and pressing the SEND button, the sensor enters test mode (hold time is 3s), and standby time and daylight sensor are disabled. Press the TEST button again to quit this mode. |
Daylight Function Configuration
- Press the OFF button; the remote LED indicators will show the latest parameters.
- Long press the [adjust button] for 3-5 seconds until the brightness indicator light turns on.
- Press the [daylight setting button] to select daylight lux: 10 lux, 30 lux, 50 lux, 100 lux.
- Aim at the target sensor and press the SEND button to upload the new parameter. The luminaire will flicker ON and OFF once as confirmation.
- Aim at the target sensor and long press the [daylight setting button] to turn off the daylight sensor function.
Daylight Priority Mode: The illuminance values to turn the lamp on/off automatically controlled by the photocell are: 10lx/50lx, 30lx/100lx, 50lx/150lx, 100lx/200lx.
Daylight Threshold Mode: The illuminance value to turn the lamp on when motion is detected, controlled by the photocell, are: 10lx, 30lx, 50lx, 100lx.
LED Indicators
| LED | Description | LED | Description | LED | Description |
|---|---|---|---|---|---|
| BRIGHTNESS | High end trim turning function (To set the output level of connected lighting during occupancy). | STANDBY DIM | To set the output level of connected lighting during vacancy. The sensor will regulate the lighting output at the set level. | HOLD TIME | The time that the Sensor will dim the light to a low level after the area is vacated. |
| STANDBY TIME | Represents the time that the sensor will keep the light at a low dim level after the HOLD TIME has elapsed. | SENSITIVITY | To set the occupancy sensing sensitivity of the Sensor. | DAYLIGHT SENSOR | When the natural light level exceeds the setpoint, the light will turn off even if the space is occupied. The light automatically turns on at 10% when natural light is insufficient (no motion). |
Performance Examples
Scenario 1:
- 21:00: Light switches on at 100% when movement is detected.
- 21:10: Light dims to standby level (10%) after the hold-time (30min) expires.
- 21:40: Light remains in dimming level at night.
Scenario 2:
- 100% on when movement detected, and dims to 10% in long absence.
Demonstration Settings: Brightness: 100%, Hold-time: 30min, Sensitivity: 100%, Daylight: 30lx, Stand-by Dim: 10%, Stand-by time: +∞ (Daylight priority mode: the stand-by time is only +∞, otherwise it is daylight threshold mode.)
Warning
Remove batteries from the compartment if the remote will not be used for 30 days.
