Shelly Plus Uni

Read Before Use

CAUTION: Before starting installation, carefully read this entire guide and any accompanying documents. Failure to follow procedures can lead to malfunction, danger, legal violations, or voiding of guarantees. Shelly Europe Ltd. is not liable for damage due to incorrect installation or operation.

Product Description

The Shelly Plus Uni is a compact smart universal module featuring two potential-free solid-state relays, a pulse counter, one analog input, and two digital inputs. It enables remote control of electrical devices via mobile phone, tablet, PC, or home automation systems. The device can operate standalone on a local Wi-Fi network or be controlled via cloud-based services. It can be accessed, controlled, and monitored remotely from any location with internet connectivity, provided it is connected to a Wi-Fi router and the internet. An embedded Web Interface allows for monitoring, control, and settings adjustment.

Firmware Updates: The device comes with factory-installed firmware. Shelly Europe Ltd. provides free firmware updates to keep the device up-to-date and secure. Updates can be accessed via the web interface or the Shelly Smart Control mobile application. Users are solely responsible for installing updates.

Legend (Pinout Description)

The Shelly Plus Uni has the following terminals:

• VAC1: 8-24 VAC / 9-28 VDC power supply input
• VAC2: 8-24 VAC / 9-28 VDC power supply input
• ANALOG IN: Analog input
• SENSOR VCC: Power supply output for 1-Wire sensors
• DATA: 1-Wire data signal input/output
• +5 VDC: 5 VDC positive power supply input
• GND: Device ground
• COUNT IN: Pulse counter input
• IN 1: Digital input 1
• IN 2: Digital input 2
• OUT 1: Solid-state relay 1 output
• OUT 2: Solid-state relay 2 output

Installation Instructions

WARNING! Danger of electrocution! Do not connect the Device to voltage sources higher than specified.

CAUTION! Use the Device only with power supplies and appliances compliant with all applicable regulations. Short circuits may damage the Device.

CAUTION! Do not connect to appliances exceeding the maximum load.

CAUTION! Connect the Device only as shown in these instructions. Other methods may cause damage or injury.

CAUTION! Ensure the PCB is not in contact with conductive materials during mounting.

CAUTION! For indoor use only. Keep away from liquids and moisture.

CAUTION! Do not use if damaged. Do not attempt self-repair.

General Connection: Connect the Device according to the wiring diagram. Power can be supplied via VAC 1 and VAC 2 (8-24 VAC or 9-28 VDC) or via +5 VDC and GND (stabilized 5 VDC, e.g., from a USB port).

Sensor Connections: You can connect up to five DS18B20 temperature sensors or a single DHT22 temperature and humidity sensor simultaneously.

Input Measurements: The ANALOG IN terminal can measure voltage levels up to +30 VDC (referenced to GND). The COUNT IN terminal can measure signal frequency. IN 1 and IN 2 are digital inputs.

Note: COUNT IN, IN 1, and IN 2 are triggered by voltage levels below 1.5 V.

Specifications

• Dimensions (LxWxH): 37x42x16 mm / 1.46x1.65x0.63 in (without cables)
• Weight: 8.5 g / 0.3 oz
• Ambient Temperature: -20 °C to 40 °C / -4 °F to 104 °F
• Humidity: 30 % to 70 % RH
• Power Supply: 8-24 VAC / 9-28 VDC / 5 VDC (stabilized, via +5 VDC and GND)
• Power Consumption: < 1 W
• Digital Inputs Resistance: 50 kΩ
• Digital Inputs Triggering Voltage: 1.5 V (active low level)
• Max Switching Voltage: 30 V
• Max Switching Current: 300 mA
• Voltmeter: 0-15 VDC / 0-30 VDC (Two-range)
• Pulse Counter Input Triggering Voltage: 1.5 V (active low level)
• Pulse Counter Max Frequency: 1 kHz
• External Sensors Supported: Single DHT22 or up to five DS18B20
• RF Band: 2400 - 2495 MHz
• Max. RF Power: < 20 dBm
• Wi-Fi Protocol: 802.11 b/g/n
• Wi-Fi Operational Range (depending on local conditions): up to 50 m / 160 ft outdoors, up to 30 m / 100 ft indoors
• Bluetooth Protocol: 4.2
• Bluetooth Operational Range (depending on local conditions): up to 30 m / 100 ft outdoors, up to 10 m / 33 ft indoors
• CPU: ESP32
• Flash: 4 MB
• Schedules: 20
• Webhooks (URL actions): 20 with 5 URLs per hook
• Scripting: Yes
• MQTT: Yes

Shelly Cloud Inclusion

The Shelly Plus Uni can be used with the Shelly Smart Control mobile application and cloud service. Instructions for cloud connection are available in the mobile application guide. However, the Shelly mobile application and Shelly Cloud service are not required for the device to function properly. It can be used standalone or with other home automation platforms.

CAUTION! Do not allow children to play with connected buttons/switches. Keep remote control devices (phones, tablets, PCs) away from children.

Declaration of Conformity

Shelly Europe Ltd. (formerly Allterco Robotics EOOD) declares that the radio equipment type Shelly Plus Uni complies with Directive 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU.

The full text of the EU declaration of conformity is available at: https://shelly.link/plus-uni_DoC

Manufacturer: Shelly Europe Ltd.

Address: 103 Cherni vrah Blvd., 1407 Sofia, Bulgaria

Tel: +359 2 988 7435

E-mail: support@shelly.cloud

Official Website: https://www.shelly.com

All rights to the Shelly® trademark and other intellectual property associated with this Device belong to Shelly Europe Ltd.